Operator's Manual – AutoCycle iC - Ferguson Beauregard

Recommendations

Info

ACiC Operator’s Manual Revision 4 Page 88 of 95 7.5.1 ACiC Configuration for AutoPILOT 1. Open the ACiC in iCConnect and choose the Input Config tab 2. Set the Differential pressure analog channel, Line Pressure analog channel, and Line Temperature analog channel to FCU. 3. Click the Save button. 4. Choose System tab. 5. Set the port setup sections according to Table 7.26. 6. Click the Save button. 7. Choose the FCU tab. 8. Set the appropriate MODBUS address of the AutoPILOT. 9. Set all the other FCU parameters as according to Table 7.27. 10. Click the Save button. Setting Value Port Setup (Serial or TTL) Baud Rate 19200 Parity None Flow Control No flow control Stop Bits 1 Stop bit Data Bits 8 Data bits Port Device External Device Port Protocol Flow computer (FCU) Table 7.26: iCConnect System Tab - AutoPILOT Setting Value Capture window Previous volume capture window end 60 Previous volume capture window start 0 FCU Communications FCU’s MODBUS mode False FCU’s slave mode True Flow computer present True MODBUS address 1 Prefix byte 0 Prefix byte count 0 Suffix byte 0 Suffix byte count 0 FCU Data Format Byte order DCBA Data type Single precision float Flow computer type Fisher ROC Flow rate definition MCF per day Units False FCU Registers Current volume address 7905 DP address 7901 Flow address 7904 LT address 7903 Previous volume address 7906 SP address 7902 Totalflow base group number 0 FCU Scan Response timeout 7 Scan interval 1 Table 7.27: iCConnect FCU Tab - AutoPILOT 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567
ACiC Operator’s Manual Revision 4 Page 89 of 95 7.5.2 AutoPILOT Configuration 1. Connect to the AutoPILOT using the AutoCONFIG software. 2. From the System Configurations tree, select System Configuration. 3. Set the Host Baud Rate to 19200 Comm. Address to the MODBUS Address value assigned in the ACiC. 4. Click Apply. 5. From the System Configurations tree, select Configurable Modbus Registers. 6. 7. For orifice 1, enter values as shown in Table 7.28. Click Download. For other orifices, add 100 per orifice number (i.e. 8101 for orifice 2, 8201 for orifice 3, etc.) Figure 7.39: System Configuration Register Number Data 7901 8001 7902 8002 7903 8003 7904 8004 7905 8005 7906 8008 Table 7.28: Configurable Modbus Registers 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567
Page 1 and 2:
Operator’s Manual Revision: 4 Rev
Page 3 and 4:
ACiC Operator’s Manual Revision 4
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38: ACiC Operator’s Manual Revision 4
Page 73 and 74: 1. 2. 3. 4. 5. 6. 7. 8. 9. ACiC Ope
Page 77 and 78: 1. 2. 3. 4. 5. 6. ACiC Operator’s
Page 85 and 86: 1. 2. 3. 4. 5. 6. 7. ACiC Operator
Page 87: ACiC Operator’s Manual Revision 4
Page 95: 8. 9. ACiC Operator’s Manual Revi
show all

Operator's Manual – AutoCycle iC - Ferguson Beauregard

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?