User's Manual TNC 360 (from 259 900-11) - heidenhain

More documents

Recommendations

Info

5 Programming Tool Movements TNC 360 5.1 General Information on Programming Tool Movements ..................... 5-2 5.2 Contour Approach and Departure .......................................................... 5-4 Starting and end positions .............................................................................................. 5-4 Smooth approach and departure .................................................................................... 5-6 5.3 Path Functions ......................................................................................... 5-7 General information ........................................................................................................ 5-7 Machine axis movement under program control ........................................................... 5-7 Overview of path functions ............................................................................................ 5-8 5.4 Path Contours – Cartesian Coordinates ................................................. 5-9 Straight line .................................................................................................................... 5-9 Chamfer ......................................................................................................................... 5-12 Circle and circular arcs.................................................................................................... 5-14 Circle Center CC ............................................................................................................. 5-15 Circular Path C Around the Center Circle CC ................................................................. 5-17 Circular path CR with defined radius .............................................................................. 5-20 Circular path CT with tangential connection ................................................................... 5-23 Corner rounding RND ..................................................................................................... 5-25 5.5 Path Contours – Polar Coordinates ......................................................... 5-27 Polar coordinate origin: Pole CC ..................................................................................... 5-27 Straight line LP ............................................................................................................... 5-27 Circular path CP around pole CC .................................................................................... 5-30 Circular path CTP with tangential connection................................................................. 5-32 Helical interpolation ........................................................................................................ 5-33 5.6 M-Functions for Contouring Behavior and Coordinate Data ............... 5-36 Smoothing corners: M90 ................................................................................................ 5-36 Machining small contour steps: M97 ............................................................................. 5-37 Machining open contours: M98 ..................................................................................... 5-38 Progamming machine-reference coordinates: M91/M92 ............................................... 5-39 5.7 Positioning with Manual Data Input (MDI) ............................................ 5-40
6 Subprograms and Program Section Repeats TNC 360 6.1 Subprograms ............................................................................................ 6-2 Principle ......................................................................................................................... 6-2 Operating limits .............................................................................................................. 6-2 Programming and calling subprograms .......................................................................... 6-3 6.2 Program Section Repeats ........................................................................ 6-5 Principle ......................................................................................................................... 6-5 Programming notes ........................................................................................................ 6-5 Programming and calling a program section repeat ....................................................... 6-5 6.3 Main Program as Subprogram ................................................................ 6-8 Principle ......................................................................................................................... 6-8 Operating limits .............................................................................................................. 6-8 Calling a main program as a subprogram ....................................................................... 6-8 6.4 Nesting ...................................................................................................... 6-9 Nesting depth ................................................................................................................. 6-9 Subprogram in a subprogram ......................................................................................... 6-9 Repeating program section repeats ............................................................................... 6-11 Repeating subprograms ................................................................................................. 6-12
Page 1 and 2: May 1994 HEIDENHAIN User's Manual H
Page 3 and 4: TNC Guideline: From workpiece drawi
Page 5 and 6: How to use this manual TNC 360 This
Page 7 and 8: Contents User's Manual TNC 360 (fro
Page 9 and 10: 2 Manual Operation and Setup TNC 36
Page 11: 4 Programming TNC 360 4.1 Editing p
Page 15 and 16: 8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18: 10 External Data Transfer TNC 360 1
Page 19 and 20: 12 Tables, Overviews, Diagrams TNC
Page 21 and 22: 1 Introduction 1.1 The TNC 360 The
Page 23 and 24: 1 Introduction 1.1 The TNC 360 TNC
Page 25 and 26: 1 Introduction 1.2 Fundamentals of
Page 31 and 32: 1 Introduction Programming tool mov
Page 33 and 34: 1 Introduction 1.4 Graphics and Sta
Page 35 and 36: 1 Introduction 1.4 Graphics and Sta
Page 37 and 38: 1 Introduction 1.5 Programs The TNC
Page 39 and 40: 1 Introduction 1.5 Programs To remo
Page 41 and 42: 2 Manual Operation and Setup Traves
Page 43 and 44: 2 Manual Operation and Setup 2.2 Sp
Page 45 and 46: 2 Manual Operation and Setup 2.3 Se
Page 47 and 48: 2 Manual Operation and Setup 2.4 3D
Page 57 and 58: 2 Manual Operation and Setup 2.6 Me
Page 59 and 60: 2 Manual Operation and Setup 2.6 Me
Page 61 and 62: 3 Test Run and Program Run 3.1 Test
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4-2 In the PROGRAMMIN
Page 69 and 70:
4 Programming 4.1 Editing Part Prog
Page 71 and 72:
4 Programming 4.2 Tools 4-6 Determi
Page 73 and 74:
4 Programming 4.2 Tools Entering to
Page 75 and 76:
4 Programming 4.2 Tools Tool change
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.3 Tool Compensation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
4 Programming 4-20 Generating a new
Page 87 and 88:
5 Programming Tool Movements 5.1 Ge
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
5 Programming Tool Movements 5.6 M-
Page 123 and 124:
5 Programming Tool Movements 5.6 M-
Page 125 and 126:
6 Subprograms and Program Section R
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
8 Cycles 8.1 General Overview of Cy
Page 157 and 158:
8 Cycles 8.1 General Overview Dimen
Page 159 and 160:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 161 and 162:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 163 and 164:
8 Cycles 8.2 Simple Fixed Cycles SL
Page 165 and 166:
8 Cycles 8.2 Simple Fixed Cycles PO
Page 167 and 168:
8 Cycles 8.2 Simple Fixed Cycles CI
Page 169 and 170:
8 Cycles 8.3 SL Cycles 8-16 Subcont
Page 171 and 172:
8 Cycles 8.3 SL Cycles ROUGH-OUT (C
Page 173 and 174:
8 Cycles 8.3 SL Cycles SL Cycles: O
Page 175 and 176:
8 Cycles 8.3 SL Cycles 8-22 Area of
Page 177 and 178:
8 Cycles 8.3 SL Cycles 8-24 Area of
Page 179 and 180:
8 Cycles 8.3 SL Cycles PILOT DRILLI
Page 181 and 182:
8 Cycles 8.3 SL Cycles 8-28 The fol
Page 183 and 184:
8 Cycles 8.4 Cycles for Coordinate
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194:
9 Digitizing 3D Surfaces 9-2 The di
Page 195 and 196:
9 Digitizing 3D Surfaces 9.2 Digiti
Page 197 and 198:
9 Digitizing 3D Surfaces 9.3 Line-B
Page 199 and 200:
9 Digitizing 3D Surfaces 9.4 Contou
Page 201 and 202:
9 Digitizing 3D Surfaces 9.4 Contou
Page 203 and 204:
9 Digitizing 3D Surfaces 9.5 Using
Page 205 and 206:
10 External Data Transfer 10.2 Pin
Page 207 and 208:
11 MOD Functions 11-2 The MOD funct
Page 209 and 210:
11 MOD Functions 11.5 Machine-Speci
Page 211 and 212:
11 MOD Functions 11.10 Setting the
Page 213 and 214:
12 Tables, Overviews, Diagrams 12.1
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237:
Miscellaneous Functions (M Function
show all

User's Manual TNC 360 (from 259 900-11) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?