User's Manual TNC 360 (from 259 900-11) - heidenhain

More documents

Recommendations

Info

12 Tables, Overviews, Diagrams 12.1 General User Parameters 12-2 General user parameters are machine parameters which affect the behavior of the TNC. These parameters set such things as: • Dialog language • Interface behavior • Traversing speeds • Machining sequence • Effect of the overrides Selecting the general user parameters General user parameters are selected with code number 123 in the MOD functions. The MOD functions also include machine-specific user parameters. Parameters for external data transfer These parameters define control characters for blockwise transfer. Input values: Number between 0 and 32 382 (ASCII character with 16-bit coding) Note: The character defined here for end of program is also valid for the setting of the standard interface. MP 5010 Function M P Bit • End of program 5010.0 .................................................................................. 0 to 7 • Beginning of program 5010.0 .................................................................................. 8 to 15 • Data input 5010.1 .................................................................................. 0 to 15 • Data output 5010.2 .................................................................................. 0 to 15 • Beginning of command block 5010.3 .................................................................................. 0 to 7 • End of command block 5010.3 .................................................................................. 8 to 15 • Positive acknowledgment 5010.4 .................................................................................. 0 to 7 • Negative acknowledgment 5010.4 .................................................................................. 8 to 15 • End of data transfer 5010.5 .................................................................................. 0 to 15 TNC 360
12 Tables, Overviews, Diagrams 12.1 General User Parameters TNC 360 Integrating the TNC interfaces to external devices: Data format and transmission stop Input value: number between 0 and 255 Sum of the individual values from the “value” column. MP 5020 Function Selections Values • Number of data bits 7 data bits (ASCII code, 8th bit = parity) .................................... +0 8 data bits (ASCII code, 9th bit = parity) .................................... +1 • Block Check Character (BCC) BCC can be any character ............................................................ +0 BCC control character not allowed ............................................... +2 • Transmission stop with RTS Active ........................................................................................... +4 Inactive ......................................................................................... +0 • Transmission stop with DC3 Active ........................................................................................... +8 Inactive ......................................................................................... +0 • Character parity Even ............................................................................................. +0 Odd ............................................................................................. +16 • Character parity Not desired ................................................................................... +0 Desired ....................................................................................... +32 • Number of stop bits 1 1 / 2 stop bits ................................................................................ +0 2 stop bits .............................................................................. +64 1 stop bit .............................................................................. +128 1 stop bit .............................................................................. +192 Example To adapt the TNC interface to an external non-HEIDENHAIN device, use the following setting: 8 data bits, BCC any character, transmission stop with DC3, even character parity, character parity desired, 2 stop bits. Input value: 1+0+8+0+32+64 = 105, so enter 105 for MP 5020. Interface type MP 5030 Function Selections Value • Interface type Standard .......................................................................................... 0 Interface for blockwise transfer ...................................................... 1 12-3
Page 1 and 2:
May 1994 HEIDENHAIN User's Manual H
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 (fro
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing p
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 External Data Transfer TNC 360 1
Page 19 and 20:
12 Tables, Overviews, Diagrams TNC
Page 21 and 22:
1 Introduction 1.1 The TNC 360 The
Page 23 and 24:
1 Introduction 1.1 The TNC 360 TNC
Page 25 and 26:
1 Introduction 1.2 Fundamentals of
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
1 Introduction Programming tool mov
Page 33 and 34:
1 Introduction 1.4 Graphics and Sta
Page 35 and 36:
1 Introduction 1.4 Graphics and Sta
Page 37 and 38:
1 Introduction 1.5 Programs The TNC
Page 39 and 40:
1 Introduction 1.5 Programs To remo
Page 41 and 42:
2 Manual Operation and Setup Traves
Page 43 and 44:
2 Manual Operation and Setup 2.2 Sp
Page 45 and 46:
2 Manual Operation and Setup 2.3 Se
Page 47 and 48:
2 Manual Operation and Setup 2.4 3D
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
2 Manual Operation and Setup 2.6 Me
Page 59 and 60:
2 Manual Operation and Setup 2.6 Me
Page 61 and 62:
3 Test Run and Program Run 3.1 Test
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4-2 In the PROGRAMMIN
Page 69 and 70:
4 Programming 4.1 Editing Part Prog
Page 71 and 72:
4 Programming 4.2 Tools 4-6 Determi
Page 73 and 74:
4 Programming 4.2 Tools Entering to
Page 75 and 76:
4 Programming 4.2 Tools Tool change
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.3 Tool Compensation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
4 Programming 4-20 Generating a new
Page 87 and 88:
5 Programming Tool Movements 5.1 Ge
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
5 Programming Tool Movements 5.6 M-
Page 123 and 124:
5 Programming Tool Movements 5.6 M-
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
8 Cycles 8.1 General Overview of Cy
Page 157 and 158:
8 Cycles 8.1 General Overview Dimen
Page 159 and 160:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 161 and 162: 8 Cycles 8.2 Simple Fixed Cycles 8-
Page 163 and 164: 8 Cycles 8.2 Simple Fixed Cycles SL
Page 165 and 166: 8 Cycles 8.2 Simple Fixed Cycles PO
Page 167 and 168: 8 Cycles 8.2 Simple Fixed Cycles CI
Page 169 and 170: 8 Cycles 8.3 SL Cycles 8-16 Subcont
Page 171 and 172: 8 Cycles 8.3 SL Cycles ROUGH-OUT (C
Page 173 and 174: 8 Cycles 8.3 SL Cycles SL Cycles: O
Page 175 and 176: 8 Cycles 8.3 SL Cycles 8-22 Area of
Page 177 and 178: 8 Cycles 8.3 SL Cycles 8-24 Area of
Page 179 and 180: 8 Cycles 8.3 SL Cycles PILOT DRILLI
Page 181 and 182: 8 Cycles 8.3 SL Cycles 8-28 The fol
Page 183 and 184: 8 Cycles 8.4 Cycles for Coordinate
Page 191 and 192: 8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194: 9 Digitizing 3D Surfaces 9-2 The di
Page 195 and 196: 9 Digitizing 3D Surfaces 9.2 Digiti
Page 197 and 198: 9 Digitizing 3D Surfaces 9.3 Line-B
Page 199 and 200: 9 Digitizing 3D Surfaces 9.4 Contou
Page 201 and 202: 9 Digitizing 3D Surfaces 9.4 Contou
Page 203 and 204: 9 Digitizing 3D Surfaces 9.5 Using
Page 205 and 206: 10 External Data Transfer 10.2 Pin
Page 207 and 208: 11 MOD Functions 11-2 The MOD funct
Page 209 and 210: 11 MOD Functions 11.5 Machine-Speci
Page 211: 11 MOD Functions 11.10 Setting the
Page 215 and 216: 12 Tables, Overviews, Diagrams 12.1
Page 237: Miscellaneous Functions (M Function
show all

User's Manual TNC 360 (from 259 900-11) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?