GE863-QUAD / PY Software User Guide

More documents

Recommendations

Info

• wait for response: GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 Response Reason Action OK Context parameters have been proceed ahead successfully stored ERROR some error occurred Check parameters and retry. For example: 1- Let's assume you want to set-up the GPRS context number 1(cid) written before with your GPRS requested QoS parameters: precedence class: High priority delay class: subscribed reliability class: subscribed peak throughput: subscribed mean throughput: best effort command: AT+CGQREQ= 1,1,0,0,0,31 response OK Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 104 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 4.3 GPRS context activation and data state entering This operation corresponds to the dial and connect of a CSD GSM data call issued to an internet service provider. • send command ATD*99***# where: is the index number of the desired context to be used (up to 5 different context). • wait for response: Response Reason Action CONNECT The GPRS connection is being processed Proceed ahead with the authentication & Packed data protocol ERROR Some error occurred Check context parameters and retry. See par. 4.2.1, 4.2.2, 4.2.3 Check also Network registration status. See par. 0 +CME ERROR: some error occurred Check context parameters and retry. See par. 4.2.1, 4.2.2, 4.2.3 Check also Network registration status. See par. 0 For example: 1- Let's assume you want to activate and enter the GPRS state with context number 1(cid) written before with your GPRS requested QoS parameters: command: ATD*99***1# response CONNECT At this point, your application should start the PPP protocol with the LCP Exchange phase: LCP Configure Request LCP Configure Acknowledge PAP Authentication PAP-Ack Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 105 of 117
Page 1 and 2:
GE863-QUAD / PY Software User Guide
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
2.5.2.3 Provide SIM PIN (only if re
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
For example: 1 - Let's assume that
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
AT+CPBR=7 the response may look lik
Page 41 and 42:
3.1.5 Phonebook entry Delete As fir
Page 43 and 44:
Page 45 and 46:
3.2.1.1 Set the extended incoming c
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54: GE863-QUAD / PY Software User Guide
Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
Page 63 and 64: - Data Coding Scheme - page number
Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
Page 99 and 100: 4.1.1 CSD application example GE863
Page 103: GE863-QUAD / PY Software User Guide
Page 111 and 112: MAIL FROM: GE863-QUAD / PY Softwar
Page 117: GE863-QUAD / PY Software User Guide
show all

GE863-QUAD / PY Software User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?