GE863-QUAD / PY Software User Guide

More documents

Recommendations

Info

GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 2.6.1.4 Check for microphone mute setting The microphone of the active path can be muted with an AT command; to be sure that it is not muted, it is suggested to check it with this command: • Send command AT+CMUT • wait for response in the format: +CMUT: OK where: is the muting setting for the microphone: 0 - microphone active 1 - microphone muted NOTE: The mute setting is different from Volume setting: it refers to both the audio paths, the mute setting will remain even when changing audio path. 2.6.2 Phone number dialing 2.6.2.1 Dial a given phone number • Send command ATD where: is the phone number to be dialed • wait for response: Response Reason Action OK The call has been placed Wait for the other party to lift the receiver.. BUSY The line called is busy retry later NO ANSWER The receiver did not answer the retry later NO CARRIER call Call placing has not been successful check for mobile registration and signal strength (par. 0) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 26 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 For example: 1- Let's assume you have to call the national number 040 - 4192111, command: ATD 0404192111 response OK 2- Let's assume you have to call the national number but in international format +39-40-4192111, command: ATD +39404192111 response OK 3- Let's assume you have to call the international number +386-40-4192111 without previously setting the +FCLASS=8 (voice), command: ATD +386404192111; response OK 2.6.3 Closing the voice call 2.6.3.1 Hang up the voice call • Send command ATH • wait for response OK TIP: during the voice call the device remains in command mode, so the escape sequence (+++) must not be issued before sending commands. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 27 of 117
Page 1 and 2: GE863-QUAD / PY Software User Guide
Page 17 and 18: 2.5.2.3 Provide SIM PIN (only if re
Page 25: For example: 1 - Let's assume that
Page 39 and 40: AT+CPBR=7 the response may look lik
Page 41 and 42: 3.1.5 Phonebook entry Delete As fir
Page 45 and 46: 3.2.1.1 Set the extended incoming c
Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
Page 63 and 64: - Data Coding Scheme - page number
Page 77 and 78:
GE863-QUAD / PY Software User Guide
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
esponse: +CCLK="02/11/07,13:24:47"
Page 97 and 98:
Page 99 and 100:
4.1.1 CSD application example GE863
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
MAIL FROM: GE863-QUAD / PY Softwar
Page 113 and 114:
Page 115 and 116:
Page 117:
show all

GE863-QUAD / PY Software User Guide

Create successful ePaper yourself

Delete template?

Save as template?