GE863-QUAD / PY Software User Guide

More documents

Recommendations

Info

Example of an ftp file transfer: GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 AT+CGDCONT=1,"IP","apn" OK AT#GPRS=1 +IP:xxx.xxx.xxx.xxx OK AT#FTPOPEN="xxx.xxx.xxx.xxx","username","password", 0 OK AT#FTPTYPE=0 OK AT#FTPTO=1000 OK AT#FTPPUT="file.txt" CONNECT (send the file) +++ NOCARRIER AT#FTPCLOSE OK AT#GPRS=0 OK For the rest of available commands on the FTP functionality please refer to the full AT commands specification. TIP: The #GPRS command activates the context and it is necessary to start the FTP connection. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 114 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 6 CAMERA OPERATIONS 6.1 Easy Camera - Send photo via EMAIL Let' suppose we want to send, with our embedded device, a taken photo via EMAIL by using a SMTP server. Initial data: Server to be contacted: smtp.domain.com Application Layer Protocol: SMTP (RFC821) Sender: "GE863-QUAD / PY" Receiver: "Receiver" Subject: Email Test Message body: this message is sent for test Easy CAMERA feature. Hello World! GPRS settings: APN: internet.gprs IP of GPRS device: dynamically assigned by the network DNS: assigned by the network USERID: EASY GPRS PASSWORD: EASY GPRS SMTP settings: USERID: SMTP USER PASSWORD: SMTP PASSW Now we have all the information needed to configure our system. With our microcontroller we issue to the GE863-QUAD / PY the following AT commands: AT+CGDCONT=1,"IP","internet.gprs","0.0.0.0",0,0 (1-GPRS context setting) AT#USERID = "EASY GPRS" (2-Authentication setting) AT#PASSW = "EASY GPRS" (3-Authentication setting) AT#ESMTP = "smtp.domain.com" (4-SMTP server setting) AT#EUSER = "SMTP USER" (5-Authentication setting) AT#EPASSW = "SMTP PASSW" (6-Authentication setting) AT#EADDR= "GE863@telit.net" (7-Sender address setting) NOTE: Authentication settings could be different between GPRS and SMTP. This is due to the fact that in the GPRS authentication it is requested user and password of your internet provider, instead of the SMTP authentication where user and password is used to connect to the SMTP server. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 115 of 117
Page 1 and 2:
GE863-QUAD / PY Software User Guide
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
2.5.2.3 Provide SIM PIN (only if re
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
For example: 1 - Let's assume that
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
AT+CPBR=7 the response may look lik
Page 41 and 42:
3.1.5 Phonebook entry Delete As fir
Page 43 and 44:
Page 45 and 46:
3.2.1.1 Set the extended incoming c
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
• wait for OK GE863-QUAD / PY Sof
Page 63 and 64: - Data Coding Scheme - page number
Page 65 and 66: GE863-QUAD / PY Software User Guide
Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
Page 99 and 100: 4.1.1 CSD application example GE863
Page 111 and 112: MAIL FROM: GE863-QUAD / PY Softwar
Page 113: GE863-QUAD / PY Software User Guide
Page 117: GE863-QUAD / PY Software User Guide
show all

GE863-QUAD / PY Software User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?