GE863-QUAD / PY Software User Guide

More documents

Recommendations

Info

GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 5 FTP OPERATIONS A set of AT commands is available to support the Ftp activities. A fist command is called #FTPTO (FTP Time-Out) which defines the time-out for FTP operations. The module has already a factory default time defined that is 100ms. If it is needed to be modified, the syntax is: AT#FTPTO[=] Parameter: - time-out in 100 ms units 100..5000 - hundreds of ms (factory default is 100) Note: The parameter is not saved in NVM. Note: if parameter is omitted the behaviour of Set command is the same as Read command. Example: AT#FTPTO=1000 OK (set the timeout to 100sec) 5.1 Opening and Closing an FTP Connection With the command AT#FTPOPEN=,,, is possible to open the FTP connection. The parameters are: - string type, address and port of FTP server (factory default port 21). - string type, authentication user identification string for FTP. - string type, authentication password for FTP. 0 - active mode (default) 1 - passive mode In order to close the FTP connection the command to be used is AT#FTPCLOSE. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 112 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 5.2 Setting the FTP Transfer Type With the command AT#FTPTYPE[=] is possible to configure the file transfer type. The command must be provided during an FTP connection. Parameter: - file transfer type: 0 - binary 1 - ascii Note: The command causes an ERROR result code to be returned if no FTP connection has been opened yet. Note: If the parameter is omitted then the behaviour of Set command is the same of Read command. 5.3 FTP File transfer to the server With the command AT#FTPPUT= , to issued during an FTP connection, is possible to open a data connection and starts sending file to the FTP server. If the data connection succeeds, a CONNECT indication is sent, otherwise a NO CARRIER indication is sent. Parameter: - string type, name of the file. Note: use the escape sequence +++ to close the data connection. Note: The command causes an ERROR result code to be returned if no FTP connection has been opened yet. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 113 of 117
Page 1 and 2:
GE863-QUAD / PY Software User Guide
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
2.5.2.3 Provide SIM PIN (only if re
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
For example: 1 - Let's assume that
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
AT+CPBR=7 the response may look lik
Page 41 and 42:
3.1.5 Phonebook entry Delete As fir
Page 43 and 44:
Page 45 and 46:
3.2.1.1 Set the extended incoming c
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
Page 63 and 64: - Data Coding Scheme - page number
Page 65 and 66: GE863-QUAD / PY Software User Guide
Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
Page 99 and 100: 4.1.1 CSD application example GE863
Page 111: MAIL FROM: GE863-QUAD / PY Softwar
Page 117: GE863-QUAD / PY Software User Guide
show all

GE863-QUAD / PY Software User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?