1 Turn off the power of the printer. - Van Mechelen

More documents

Recommendations

Info

GS \ nL nH [Function] [Code] Specifying the relative vertical position of a character in PAGE MODE HH [Range] 0 nL 255 0 nH 255 [Outline] [Caution] This command is used in PAGE MODE to specify the vertical position of a character in the data mapping start position, in a relative position with respect to the current position. The next data mapping start position will be at a point [(nL + nH × 256)× basic calculation pitch] inches away from the current position. • This command is ignored when PAGE MODE is not selected. • If a new position is specified for a character located beneath the current position, it should be specified as positive (+). If it is above the current position, it should be negative (-). • A negative value is the complement of 65536. For example, to move the position by N pitches up, specify it as: nL + nH × 256 = 65536 - N • The specification of a relative position outside the specified print area is ignored. • Depending on the start point specified by ESC T, this command acts as follows: (1) If the start point is the top left or bottom right, the command specifies the relative position in the paper feed direction (The character’s top-bottom direction) using the vertical basic calculation pitch (y). (2) If the start point is the top right or bottom left, the command specifies the relative position in the direction perpendicular to the paper feed (The character’s top-bottom direction) using the horizontal basic calculation pitch (x). • The basic calculation pitch is set by GS P. • Fractions resulting from calculations are corrected with the minimum pitch of the mechanism, and the remainder is omitted. — 112 —
GS ^ n1 n2 n3 [Function] [Code] Executing the macro HH [Range] 0 n1 255 0 n2 255 0 n3 1 [Outline] [Caution] [Default] [See Also] GS : [Sample Program] Executing contents defined in macro. n1 : The number of times of macro execution n2 : Waiting time on macro execution Waiting time of n2 × 100 msec is given for every execution. n3 : Macro execution mode n3=0 Continuous execution: The Macro is executed “n1” times continuously at the time interval specified by “n2”. n3=1 Execution by FEED Switch: After waiting for the time specified by “n2”, the ARARM LED flickers and the FEED switch is waiting to be pressed. When it is pressed, the macro is executed once. This action is repeated “n1” times. • When this command is received while in macro definition, suspension of macro definition is indicated. At this time, the defined content is cleared. • No execution takes place when the macro is held undefined or n1=0. • While in macro execution with n3=1, paper feed with the FEED switch is not available. The initial value is not defined. Refer to Sample Program and Print Results for GS: on page 101. — 113 —
Page 1 and 2:
41.12.08 014/42.55.99 014/59.26.95
Page 3 and 4:
IMPORTANT SAFETY INSTRUCTIONS • R
Page 5 and 6:
IMPORTANT: This equipment generates
Page 7 and 8:
SAFETY PRECAUTIONS — WHICH SHOULD
Page 9 and 10:
PRECAUTIONS FOR INSTALLATION • Do
Page 11 and 12:
In the position indicated below, a
Page 13 and 14:
i DAILY MAINTENANCE Cleaning the pr
Page 15 and 16:
6. PARALLEL INTERFACE .............
Page 17 and 18:
INHALT 4. BETRIEB ................
Page 19 and 20:
1. GENERAL OUTLINE The CBM1000 is a
Page 21 and 22:
2. BASIC SPECIFICATIONS 2.1 Model C
Page 23 and 24:
2.3 Print Paper Specifications 2.3.
Page 25 and 26:
2.3.3 Used Paper Form unit=mm Symbo
Page 27 and 28:
3. OUTER APPEARANCE AND COMPONENT P
Page 29 and 30:
4. OPERATION 4.1 Connecting the AC
Page 31 and 32:
4.3 Connecting the Drawer Kick-Out
Page 33 and 34:
6 Remove an excess length of paper
Page 35 and 36:
4.6 Using 58 mm Wide Paper Rolls 1
Page 37 and 38:
4.9 Operation Panel and Error Indic
Page 39 and 40:
Waiting for label cutter action: Wa
Page 41 and 42:
5. SETTING DIP SWITCHES 5.1 Locatio
Page 43 and 44:
DIP switch 2 No. Function ON OFF Fa
Page 45 and 46:
6. PARALLEL INTERFACE 6.1 Bidirecti
Page 47 and 48:
CAUTION: • The first letter “n
Page 49 and 50:
6.2.3 Timing Chart (Compatibility M
Page 51 and 52:
7.2 Connector Pin Configuration No.
Page 53 and 54:
7.3.2 Error Detection Detection of
Page 55 and 56:
8. DRAWER KICK-OUT CONNECTOR AND PO
Page 57 and 58:
9. MAINTENANCE AND SERVICE For the
Page 59 and 60:
No. Command Function Mode Code Page
Page 61 and 62:
Label Control No. Command Function
Page 63 and 64:
10.2.2 Command Details HT [Function
Page 65 and 66:
CR [Function] [Code] Back to printi
Page 67 and 68:
CAN [Function] [Code] [Outline] [Ca
Page 69 and 70:
(1) Printer status (When n = 1 is s
Page 71 and 72:
DLE ENQ n [Function] [Code] Real-ti
Page 73 and 74:
ESC FF [Function] [Code] [Outline]
Page 75 and 76:
[Sample Program] [Print Results] LP
Page 77 and 78:
[Sample Program] LPRINT CHR$(&H1B)
Page 79 and 80: [Sample Program] [Print Results] LP
Page 81 and 82: ESC & s n m [a [p] s×a] m-n+1 [Fun
Page 83 and 84: ESC * m n1 n2 [ d ] k [Function] [C
Page 85 and 86: ESC - n [Function] [Code] Specifyin
Page 87 and 88: ESC 3 n [Function] [Code] Setting l
Page 89 and 90: ESC n [Function] [Code] Deleting d
Page 91 and 92: ESC D [ n ] k NUL [Function] [Code]
Page 93 and 94: ESC G n [Function] [Code] Specifyin
Page 95 and 96: ESC L [Function] [Code] [Outline] [
Page 97 and 98: ESC R n [Function] [Code] Selecting
Page 99 and 100: ESC T n [Function] [Code] Selecting
Page 101 and 102: ESC W xL xH yL yH dxL dxH dyL dyH [
Page 103 and 104: ESC \ nL nH [Function] [Code] Speci
Page 105 and 106: ESC c 3 n [Function] [Code] Selecti
Page 107 and 108: ESC c 5 n [Function] [Code] Enablin
Page 109 and 110: ESC p m n1 n2 [Function] [Code] Gen
Page 111 and 112: ESC { n [Function] [Code] Specifyin
Page 113 and 114: [Default] n = 0 [See Also] ESC !
Page 115 and 116: GS * n1 n2 [ d ] n1×n2×8 [Functio
Page 117 and 118: GS ( A pL pH n m [Function] [Code]
Page 119 and 120: GS : [Function] [Code] [Outline] [C
Page 121 and 122: GS H n [Function] [Code] Selecting
Page 123 and 124: GS I n [Function] [Code] Sending th
Page 125 and 126: [Default] nL = 0, nH = 0 [See Also]
Page 127 and 128: GS V m ......... (1) GS V m n .....
Page 129: (2) If a sufficient area cannot be
Page 133 and 134: (1) 1st byte (Printer information)
Page 135 and 136: GS f n [Function] [Code] Selecting
Page 137 and 138: GS k m [d1 ..... dk] NUL GS k m n [
Page 139 and 140: [Default] For PAGE MODE: • This c
Page 141 and 142: CODABAR (NW-7) CODE93 This bar code
Page 143 and 144: [Sample Program] Special characters
Page 145 and 146: GS r n [Function] [Code] Sending st
Page 147 and 148: GS v 0 m xL xH yL yH d1...dk [Funct
Page 149 and 150: GS w n [Function] [Code] Specifying
Page 151 and 152: [Caution] [Reference] • Because f
Page 153 and 154: [Caution] [Reference] • When the
Page 155 and 156: • When the size of a bit image ex
Page 157 and 158: • If outside-defined-area argumen
Page 159 and 160: GS FF [Function] [Code] [Outline] [
Page 161 and 162: GS C0 m n [Function] [Code] [Range]
Page 163 and 164: GS C2 n1 n2 [Function] [Code] Setti
Page 165 and 166: GS c [Function] [Code] [Outline] Pr
Page 167 and 168: 11.1.3 Codepage PC850 (Multilingual
Page 169 and 170: 11.1.7 Codepage PC852 (Eastern Euro
Page 171 and 172: 11.2 International Character Codes
Page 173 and 174: 12.2 Mapping of print data in the p
Page 175 and 176: 12.2.1 Example of the Use of PAGE M
Page 177 and 178: Before an FF is sent, the following
Page 179 and 180: 13.1.2 Interfacing Phases Interfaci
Page 181 and 182:
13.2.3 Precautions 1) The Negotiati
Page 183 and 184:
12) If the host selected the Revers
Page 185 and 186:
(1) Termination through a handshake
Page 187 and 188:
15. APPENDIX 4. OUTLINE DRAWING 15.
Page 189 and 190:
15.3 AC Adapter (31AD) —171 —
Page 191 and 192:
GERMAN — 173 —
Page 193 and 194:
SICHERHEITSVORSCHRIFTEN — BITTE U
Page 195 and 196:
VORSICHTSMASSNAHMEN FÜR DIE INSTAL
Page 197 and 198:
Nachstehend wird ein Warnschild des
Page 199 and 200:
i TÄGLICHE WARTUNGSARBEITEN Reinig
Page 201 and 202:
ACHTUNG : • Verwenden Sie ausschl
Page 203 and 204:
4.3 Anschließen des Drawer Kickout
Page 205 and 206:
6 Trennen Sie das überstehende Pap
Page 207 and 208:
4.6 Verwenden von 58 mm breiten Pap
Page 209 and 210:
4.9 Bedienungsfeld und Fehleranzeig
Page 211 and 212:
werden der Papierschneider und der
Page 213 and 214:
5. EINSTELLEN DER DIP-SCHALTER 5.1
Page 215 and 216:
DIP-Schalter 2 No. Funktion ON OFF
Page 217 and 218:
6. PARALLELE SCHNITTSTELLE 6.1 Bidi
Page 219 and 220:
ACHTUNG: • Wenn der erste Buchsta
Page 221 and 222:
6.2.3 Timing-Tabelle (Kompatibilit
Page 223 and 224:
7.2 Belegung der Anschlußstifte No
Page 225 and 226:
(6) FG Hierbei handelt es sich um e
Page 227 and 228:
8. DRAWER KICKOUT-ANSCHLUSS UND STR
Page 229 and 230:
9. WARTUNG UND KUNDENDIENST Informa
show all

1 Turn off the power of the printer. - Van Mechelen

Create successful ePaper yourself

Delete template?

Save as template?