BD01 System – 40 ... 160 A - GRUP DAP

© Siemens AG 2007
BD2 System — 160 ... 1250 A
General data
Feeder units
Conductor cross-sections
Version Type L1, L2, L3 N PE Size of
terminal
Feeder units with terminal
bolt
Center feeder units with
terminal bolts
min.
mm 2
max.
mm 2
BD2.-250-EE (1–3) × 6 1 × 150,
2 × 70
BD2.-400-EE (1–3) × 10 1) 1 × 240,
2 × 120
BD2.-1000-EE (1–3) × 10 1) 2 × 240,
3 × 185
BD2.-1250-EE (1–4) × 10 1) 3 × 300,
4 × 240
BD2.-400-ME (1–3) × 10 1) 2 × 240,
3 × 185
BD2.-1000-ME (1–5) × 10 1) (1–5) × 300 (1–5) × 10 1) (1–5) × 300 (1–5) × 10 1) (1–5) × 300 M12
1) Minimum possible cable cross-section for cable lugs.
min.
mm 2
max.
mm 2
(1–3) × 6 1 × 150,
2 × 70
(1–3) × 10 1) 1 × 240,
2 × 120
(1–3) × 10 1) 2 × 240,
3 × 185
(1–4) × 10 1) 3 × 300,
4 × 240
(1–3) × 10 1) 2 × 240,
3 × 185
min.
mm 2
max.
mm 2
(1–3) × 6 1 × 150,
2 × 70
(1–3) × 10 1) 1 × 240,
2 × 120
(1–3) × 10 1) 2 × 240,
3 × 185
(1–4) × 10 1) 3 × 300,
4 × 240
(1–3) × 10 1) 2 × 240,
3 × 185
screws,
bolts
L1, L2, L3, N, PE
M10
M12
M12
M12
M12
Cable and wiring entries
Type BD2.-250-EE BD2.-400-EE BD2.-1000-EE, BD2.-1000-ME BD2.-1250-EE
BD2.-400-ME
Cable grommets 1 × KT3 1) 2 × KT4 1) 3 × KT4 1) 6 × KT4 1) 4 × KT4 1)
For cable diameter mm 14 ... 54 14 ... 68 14 ... 68 14 ... 68 14 ... 68
1) With strain relief.
Cable entry plate for single core cable
(undrilled cable entry plates)
Type BD2.-250-EE BD2.-400-EE BD2.-1000-EE BD2.-1250-EE
Cable entry plate BD2-250-EBAL BD2-400-EBAL BD2-1000-EBAL BD2-1250-EBAL
Number of cable entries (maximum) 10 × M32, 10 × M40 15 × M40, 36 × M50
5 × M40 6 × M50 and 4 × M40
Use plastic cable glands with strain relief (not included as standard)
Cable entry plate for single core cable with center feeder units
(undrilled cable entry plates)
Type BD2.-400-ME... BD2.-1000-ME
Cable entry plate BD2-400-MBAL BD2-1000-MBAL
Number of cable entries (maximum) 12 × M40 and 3 × M32, 31 × M40,
6 × M50 and 4 × M40 16 × M50 and 4 × M40
Use plastic cable glands with strain relief (not included as standard)
5
Siemens LV 70 · 2006
5/19