BD01 System â 40 ... 160 A - GRUP DAP

More documents

Recommendations

Info

NSV0_00190 NSV0_00189 BD2 System — 160 ... 1250 A © Siemens AG 2007 Fire barriers ■ Overview General requirements The German state building authorities demand that buildings are designed so that "spreading of fire and smoke is prevented, and that effective fire fighting and rescue of persons and domestic animals is facilitated". Fire or flue gas may not spread from one storey or fire area to another. All BD2A/BD2C busbar trunking systems can be equipped with a fire barrier and generally comply with the standards for buildings including high-rise buildings. The busbar trunking system is supplied ex-works with fire barriers. Retrofitting is not possible. A general approval from the German Institute for Building Engineering (Deutsches Institut für Bautechnik in Berlin DIBt) in Berlin is available: • BD2-S120: No. Z-19.15-1046, • BD2-S90: No. Z-19.15-1048). The fire resistance class with the BD2 system corresponds with version S90 or S120 according to DIN 4102 Part 9. The demands for verification of fire resistance duration at 120 min as specified to ISO 834 according to IEC/EN 60439-2 are fulfilled. The requirements for a busbar trunking system as specified to DIN 4102 are shown in the illustration. 4 3 1 • The center of the fire barrier in the trunking unit must be positioned in the center of the fire wall or ceiling. Exception: With junction units, this may not be possible due to insufficient distance from the wall or ceiling, i.e. the center of the fire barrier may not coincide with the center of the fire wall or ceiling. In such cases, PROMATECT-H(L) panels are added to achieve the actually required wall or ceiling thickness. • The following information must be provided: For BX*, BY* or BZ* trunking units, position of the center of the fire barrier in the trunking unit (or the center of the fire wall or ceiling for junction units with insufficient distance from the wall or ceiling); the desired fire resistance rating S90 or S120; and the thickness M* of the wall or ceiling. • There are no tap-off points in the area covered by the fire barrier. • The trunking units must be installed by an approved fire protection installation specialist. Notes For BX* and BY*, replace the asterisk in the type reference by the required dimension in meters from the center of the clamp terminal (end without clamp terminal) to the center of the fire wall or ceiling; for -M* specify the wall or ceiling thickness. For BZ*, replace the asterisk in the type reference by the required dimension in meters from the outside edge of limb X to the center of the fire wall or ceiling; for -M* specify the wall or ceiling thickness. 1 2 BX*, BY*, BZ* M* 1 Center line of fire barrier Positioning in the fire wall 5 NSV0_01070 (1) Permissible temperature increase on components max. 180 °C (2) Scene of fire: Application of fire according to the standard temperature curve DIN 4102, Sheet 2 (3) Permitted temperature increase of escaping air: max. 140 °C (4) No flammable gases are permitted to escape. No rescue work may be hindered by emerging smoke. Engineering To ensure fire protection to S90 or S120, the following points must be observed when engineering and installing trunking and junction units with fire barriers: M* BX*, BY*, BZ* 1 1 Center line of fire barrier Positioning in the fire ceiling 5/94 Siemens LV 70 · 2006
© Siemens AG 2007 BD2 System — 160 ... 1250 A Fire barriers ■ Design Position of fire barrier on the trunking unit L 250 NSV0_01019 BX* Type: BD2A-...-S(W).-. + BD2-S90(S120)-BX*-M* BD2C-...-S(W).-. + BD2-S120-BX*-M* Fire resistance class S90 • Wall thickness M ≥ 150 mm BD2A-...-S(W). + BD2-S90-BX*-M* 1) 150 L (L min. = 370+M) BX* min. = 185+M/2 BX*max. = L–BX* min. 520 (min.) 260 260 – – – – – – 3250 (max.) 260 2980 M NSV0_01020 Fire resistance class S120 • Wall thickness 150 mm ≤ M < 250 mm BD2A-...-S(W). + BD2-S120-BX*-M* 1) M = 150 ... 250 100 100 L (L min. = 570+M) BX* min. = 285+M/2 BX*max. = L–BX* min. 720 (min.) 360 360 – – – – – – 3250 (max.) 360 2890 NSV0_01021 • Wall thickness M ≥ 250 mm BD2A-...-S(W). + BD2-S120-BX*-M* 1) L (L min. = 370+M) BX* min. = 185+M/2 BX*max. = L–BX* min. 620 (min.) 310 310 – – – – – – 250 3250 (max.) 310 2940 5 M NSV0_01022 1) Replace the asterisk * according to the table. Siemens LV 70 · 2006 5/95
Page 1 and 2:
© Siemens AG 2007 Catalog LV 70
Page 3 and 4:
© Siemens AG 2007 SIVACON 8PS Busb
Page 5 and 6:
© Siemens AG 2007 Introduction 1/2
Page 7 and 8:
© Siemens AG 2007 Low-Voltage Cont
Page 9 and 10:
© Siemens AG 2007 oriented enginee
Page 11 and 12:
DATE: EMPLOYEE COST CENTER PAY PERI
Page 13 and 14:
© Siemens AG 2007 Universal power
Page 15 and 16:
© Siemens AG 2007 Busbar Trunking
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
© Siemens AG 2007 CD-K System - 25
Page 29 and 30:
© Siemens AG 2007 CD-K System —
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
© Siemens AG 2007 BD01 System - 40
Page 53 and 54:
© Siemens AG 2007 BD01 System —
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
NSV0_00984 NSV0_00985 © Siemens AG
Page 79 and 80:
0,10 m © Siemens AG 2007 BD01 Syst
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
© Siemens AG 2007 BD2 System - 160
Page 97 and 98:
© Siemens AG 2007 BD2 System — 1
Page 99 and 100:
Page 101 and 102:
NSV0_00118 NSV0_00124 NSV0_00119 ©
Page 103 and 104:
Page 105 and 106:
NSV0_00148 © Siemens AG 2007 BD2 S
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138: © Siemens AG 2007 BD2 System — 1
Page 147 and 148: NSV0_00460 NSV0_00459 NSV0_00458 NS
Page 151 and 152: NSV0_00470 NSV0_00470 NSV0_00470 ©
Page 155 and 156: NSV0_00485 NSV0_00484 © Siemens AG
Page 163 and 164: NSV0_00494 NSV0_00493 © Siemens AG
Page 171 and 172: NSV0_00191 © Siemens AG 2007 BD2 S
Page 187: © Siemens AG 2007 BD2 System — 1
Page 211 and 212: 11 © Siemens AG 2007 BD2 System
Page 215 and 216: © Siemens AG 2007 Appendix 6/2 Glo
Page 217 and 218: © Siemens AG 2007 Appendix Glossar
Page 219 and 220: © Siemens AG 2007 Appendix Glossar
Page 221 and 222: © Siemens AG 2007 Appendix Further
Page 223 and 224: © Siemens AG 2007 Appendix Standar
Page 225 and 226: © Siemens AG 2007 Appendix Siemens
Page 227 and 228: © Siemens AG 2007 Appendix Custome
Page 229 and 230: © Siemens AG 2007 Appendix Type re
Page 231 and 232: © Siemens AG 2007 Catalogs of the
Page 233: ens AG Busbar Trunking Systems CD-K
show all

BD01 System â 40 ... 160 A - GRUP DAP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

BD01 System â 40 ... 160 A - GRUP DAP