FELCOM 15 Operator's Manual K 7-10-09 - Furuno USA

More documents

Recommendations

Info

5. DATA REPORTING AND POLLING “Daily” is selected at step 22 (1) Press the [↓] to choose Start Time 1. (2) Press the [Enter] key to open the start time entry window. (3) Key in the start time. (4) Press the [Enter] key to close the window. (5) If necessary, key in the start time of Start Times 2-4. 25. Press the [↓] key to choose Report Contents. 26. Press the [Enter] key to open the report contents options window. 27. Press the [↓] or [↑] key to choose the contents of message report and press the [Enter] key to close the window. NAV: Position, speed, course NAV+SEA INF: Position, speed, course, water temperature, current, depth NAV(R): Position, speed, course. The difference between this and “NAV” above is that blank areas in data are shortened to lessen toll charge. FILE: Choose a file. (When chosen “FILE” is activated. Choose file with cursor and press the [Enter] key.) 28. Press the [Esc] key to show the update window. Message Report PIN Code 12345678 Message Report Programming ON FRNINMBTSTSES TELEX Status Station Name Destination Type Prefix Code Country/Ocean Code Station ID Modem Type Subject LES ID Activation Interval Time Report Times Start Time1 Start Time2 Start Time3 Start Time4 Report Contents File 583 3431997<strong>10</strong> 303 (KDDI) Daily 01:00 24 (---: No Limit) 08:00 NAV Yes Update No Message report screen 29. Yes is selected; press the [Enter] key. 30. Press the [Esc] key twice to return to the standby display. 5-6
5. DATA REPORTING AND POLLING 5.1.3 Automatic printing of data report, polling command Data reports and polling commands are automatically printed, in the default state. If you do not require automatic printing of data reports or polling commands do the following: 1. Press the [F8] key to open the Setup menu. 2. Press the [6] key to choose Auto Mode Setup. Auto Mode Setup Auto Log Print Receive Alarm Auto Receive Message Save Auto Receive Message Print Data Report & Polling Print Auto EGC Message Save Auto EGC Message Print OFF OFF OFF OFF OFF Auto mode setup menu 3. Press the [↓] or [↑] key to choose Data Report & Polling Print. 4. Press the [Enter] key to open the options window. 5. Press the [↓] key to choose OFF. (Choose ON to automatically print data report and polling command.) 6. Press the [Enter] key to close the window. 7. Press [Esc] key twice to return to the standby display. 5-7
Page 1 and 2:
OPERATOR'S MANUAL INMARSAT-C MOBILE
Page 3 and 4:
IMPORTANT NOTICES General • The o
Page 5 and 6:
TABLE OF CONTENTS FOREWORD ........
Page 7 and 8:
4.2.4 Automatically printing receiv
Page 9 and 10:
FOREWORD Introduction FURUNO Electr
Page 11 and 12:
SYSTEM CONFIGURATION ANTENNA UNIT I
Page 13 and 14:
INMARSAT C SYSTEM Inmarsat C System
Page 15 and 16:
Communications Network INMARSAT C S
Page 17 and 18:
LRIT COMPLIANCE This equipment can
Page 19 and 20:
1. OPERATIONAL OVERVIEW 1.1 Termina
Page 21 and 22:
1.2 Keyboard The FELCOM 15 is almos
Page 23 and 24:
1.2.2 Shortcut keys The FELCOM 15 p
Page 25 and 26:
1.4 Printer PP-510 (option) 1. OPER
Page 27 and 28:
1. OPERATIONAL OVERVIEW 1.5.1 Displ
Page 29 and 30:
1. OPERATIONAL OVERVIEW PV TEST CAL
Page 31 and 32:
1.6 Menu Overview 1. OPERATIONAL OV
Page 33 and 34:
1.8 Using a PC (local supply) When
Page 35 and 36:
1. OPERATIONAL OVERVIEW 6. Click th
Page 37 and 38:
1. OPERATIONAL OVERVIEW 1.8.2 Start
Page 39 and 40:
• Backing up the System System da
Page 41 and 42:
2. SYSTEM INITIALIZATION This chapt
Page 43 and 44:
2. SYSTEM INITIALIZATION 7. Press t
Page 45 and 46:
2. SYSTEM INITIALIZATION 23. Press
Page 47 and 48:
2. SYSTEM INITIALIZATION 14. You ma
Page 49 and 50:
2. SYSTEM INITIALIZATION Note: The
Page 51 and 52:
2.4 EGC Settings 2.4.1 What is the
Page 53 and 54:
2. SYSTEM INITIALIZATION 2.4.2 EGC
Page 55 and 56:
2. SYSTEM INITIALIZATION 11. Press
Page 57 and 58:
Page 59 and 60:
2. SYSTEM INITIALIZATION Automatica
Page 61 and 62:
2. SYSTEM INITIALIZATION Note: If t
Page 63 and 64:
Page 65 and 66:
2. SYSTEM INITIALIZATION 4. Name is
Page 67 and 68:
2.7 Station List 2.7.1 Adding stati
Page 69 and 70:
Page 71 and 72:
2. SYSTEM INITIALIZATION Station li
Page 73 and 74:
2.9 Creating a Directory 2. SYSTEM
Page 75 and 76:
2. SYSTEM INITIALIZATION 2.9.2 Spec
Page 77 and 78:
Page 79 and 80:
2. SYSTEM INITIALIZATION 2.11 E-mai
Page 81 and 82:
3. FILE OPERATIONS This chapter des
Page 83 and 84:
3. FILE OPERATIONS 3.2.2 Preparing
Page 85 and 86:
3. FILE OPERATION File Edit Transmi
Page 87 and 88:
3. FILE OPERATIONS Insert (with Cit
Page 89 and 90:
3. FILE OPERATIONS 10. Press the [
Page 91 and 92:
3. FILE OPERATIONS 3.3.1 Formatting
Page 93 and 94: 3. FILE OPERATIONS Save file, clear
Page 95 and 96: 3. FILE OPERATIONS 3.4.3 Opening a
Page 97 and 98: 3. FILE OPERATION 3.6 Printing File
Page 99 and 100: 3. FILE OPERATIONS 3.9 Renaming Fil
Page 101 and 102: 3. FILE OPERATIONS 7. To change fi
Page 103 and 104: 4. INMARSAT C COMMUNICATIONS This c
Page 105 and 106: 4. INMARSAT C COMMUNICATIONS 3. Pre
Page 107 and 108: 4. INMARSAT C OPERATIONS (6) Press
Page 109 and 110: 4. INMARSAT C COMMUNICATIONS Note 3
Page 113 and 114: 4. INMARSAT C COMMUNICATIONS 7. Typ
Page 115 and 116: 4. INMARSAT C COMMUNICATIONS Commun
Page 117 and 118: 4. INMARSAT C COMMUNICATIONS 4.1.3
Page 121 and 122: 4. INMARSAT C COMMUNICATIONS Manual
Page 123 and 124: 4. INMARSAT C COMMUNICATIONS Mariti
Page 125 and 126: 4. INMARSAT C COMMUNICATIONS 4.2 Re
Page 129 and 130: 4. INMARSAT C COMMUNICATIONS About
Page 133 and 134: 4.3 Log 4. INMARSAT C COMMUNICATION
Page 135 and 136: 4.4 EGC Messages 4. INMARSAT C COMM
Page 139 and 140: 5. DATA REPORTING AND POLLING This
Page 141 and 142: 5. DATA REPORTING AND POLLING 13. C
Page 143: 5. DATA REPORTING AND POLLING 9. Pr
Page 147 and 148: 5. DATA REPORTING AND POLLING • P
Page 149 and 150: 5. DATA REPORTING AND POLLING 5.2.3
Page 151 and 152: 6. DISTRESS OPERATIONS 6.1 Transmit
Page 153 and 154: 6. DISTRESS OPERATIONS 16.Press the
Page 155 and 156: 6. DISTRESS OPERATIONS 13. Press th
Page 157 and 158: 7. OTHER FUNCTIONS This chapter des
Page 159 and 160: 7.3 Choosing EGC Receiving Channel
Page 161 and 162: 7.5 LES Information 7. OTHER FUNCTI
Page 163 and 164: 8. E-MAIL BY PC 8.1 Overview The FE
Page 165 and 166: 8. E-MAIL BY PC • When a file wit
Page 167 and 168: 8. E-MAIL BY PC 8.3 Function Settin
Page 169 and 170: 8. E-MAIL BY PC 8.3.3 Gateway setti
Page 171 and 172: 8. E-MAIL BY PC 8.3.5 Restricting o
Page 173 and 174: 8. E-MAIL BY PC 8.3.7 Connection of
Page 175 and 176: 8. E-MAIL BY PC 8.3.8 Selective for
Page 177 and 178: 8. E-MAIL BY PC 8.4 E-mail Client S
Page 179 and 180: 9. MAINTENANCE, TROUBLESHOOTING Thi
Page 181 and 182: 9. MAINTENANCE, TROUBLESHOOTING Whe
Page 183 and 184: 9. MAINTENANCE, TROUBLESHOOTING 8.
Page 185 and 186: 9. MAINTENANCE, TROUBLESHOOTING DCE
Page 187 and 188: 9. MAINTENANCE, TROUBLESHOOTING 9.7
Page 189 and 190: APPENDIX Menu Tree F1: File 1. New
Page 191 and 192: APPENDIX B TECHNICAL DATA F5: Repor
Page 193 and 194: APPENDIX F8: Setup 1. Distress Aler
Page 195 and 196:
APPENDIX 6. Auto Mode Setup Auto Lo
Page 197 and 198:
APPENDIX International Telex/Teleph
Page 199 and 200:
APPENDIX Area and Country Telephone
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
APPENDIX LES List April/2002 Land e
Page 207 and 208:
APPENDIX AP-19 International Telegr
Page 209 and 210:
APPENDIX 22. "Decode failed. " File
Page 211 and 212:
APPENDIX Digital Interface (IEC 611
Page 213 and 214:
APPENDIX BWR - Bearing and distance
Page 215 and 216:
APPENDIX GLL - Geographic position
Page 217 and 218:
APPENDIX RMB - Recommended minimum
Page 219 and 220:
APPENDIX VTG - Course over ground a
Page 221 and 222:
APPENDIX Serial interface I/O circu
Page 223 and 224:
APPENDIX F U R U N O Model FELCOM 1
Page 225 and 226:
APPENDIX Antenna unit ANT RF Board
Page 227 and 228:
FURUNO FELCOM 15 SPECIFICATIONS OF
Page 229 and 230:
INDEX A Aborting ..................
Page 231:
INDEX R Receiving attachments .....
show all

FELCOM 15 Operator's Manual K 7-10-09 - Furuno USA

Create successful ePaper yourself

Delete template?

Save as template?