Installation Manual

More documents

Recommendations

Info

Chapter 4 4.15.1.5.1 Software installation My IC Social Networks is installed on individual PCs as a two part process 1. My IC Social Networks <strong>Installation</strong> Wizard is performed by an Administrator or System Installer, who has intimate knowledge of the customer’s infrastructure 2. My IC Social Networks Configuration Wizard, which is executed when the application is launched for the first time and can be performed by the end user. This uses the information provided by the Administrator/System Installer to simplify the installation process My IC Social Networks <strong>Installation</strong> Wizard Before starting the installation, make sure that Outlook and Pimphony are not running (even in background) Before starting the installation, make sure that .Net 3.5. SP1 is installed. My IC Social Networks requires Microsoft .Net Framework version 3.5 with Service Pack 1 to operate correctly. To determine if .Net 3.5 SP1 is already installed, please refer to the Microsoft Knowledge Base article (http://msdn.microsoft.com/enus/ kb/kb00318785.aspx ) 1. Run the My IC Social Networks setup.exe 2. Click Yes if you receive a UAC (user account control) warning (Windows Vista & 7) 3. Select the installation language from the languages available, click OK 4. On the “Welcome Screen”, click Next 5. Read and Accept the license Agreement, click Next 6. Select if My IC Social Networks is to connect: • directly to the OmniPCX Office (25 TAPI users) Click Next to continue. If you select TAPI Server, the next windows will ask you to indicate the Remote TAPI Server Name (or IP address). Click Next 7. Choose whether or not to enable Yahoo! integration, click Next Note: This does not install Yahoo! Messenger, but authorizes My IC Social Networks to access Yahoo! Messenger if it is installed 8. Confirm the folder to install the program into, click Next 9. Confirm the folder to install the program shortcuts into, click Next 10. Click Install to begin the installation and click Finish when the installation is complete to start the Configuration Wizard If the configuration Wizard does not continue, it can be launched at any moment from the windows menu: Start > All Programs > Alcatel-Lucent > My IC Social Networks My IC Social Networks Configuration Wizard: 1. On the "Introduction" screen, click Next 2. Enter the IP Address of the OmniPCX Office , click Next 3. The configuration wizard will connect to the OmniPCX Office . 4-122
If successfully connected, a list of available line extensions on the OmniPCX Office is presented. If unsuccessful, the invitation to enter the correct IP Address for the OmniPCX Office is presented. 4. Select the line to control and enter the voice mailbox password for that line extension, click Next 5. The configuration wizard will now authenticate the line and password with the OmniPCX Office 6. When successful, click Finish to complete the setup. If unsuccessful, the invitation to select a line and enter the correct password is displayed. 7. The configuration Wizard can be launched at any moment from windows menu: Start > All Programs > Alcatel-Lucent > My IC Social Networks 8. Once the installation is completed, start Outlook, My IC Social Networks panel will appear within Outlook interface on the right as native Outlook windows Note 1: Please ensure that TAPI configuration is setup by checking the "Location", "Area Code" and "Dialling Rules" in the TAPI control panel. Please refer to Phone and Modem Options for more details. Note 2: It is not advisable to do the installation of My IC Social Networks on a PC while connected to the published location via a VPN. Use the LAN connection to the OmniPCX Office 4.15.1.5.2 Software Uninstall My IC Social Networks can be uninstalled using standard Windows conventions from Control 4-123
Page 1 and 2:
Installation Manual Release 9.1 - J
Page 3 and 4:
Chapter 1 General Presentation Pre
Page 5 and 6:
Managed services ..................
Page 7 and 8:
System Startup from a Phone Set ...
Page 9 and 10:
_nigeb-egnahc_ _dne-egnahc_ 1.1
Page 11 and 12:
the system as well as any external
Page 13 and 14:
Figure 1.5: OmniPCX Office RCE Comp
Page 15 and 16:
2.1 Overview Alcatel-Lucent OmniPCX
Page 17 and 18:
Figure 2.2: Mini-MIX connections on
Page 19 and 20:
2.3 Installation 2.3.1 Overview
Page 21 and 22:
Board Function Optional boards Conn
Page 23 and 24:
Board used for connecting up digita
Page 25 and 26:
T2 Name T1 Name Function BUSY BUSY
Page 27 and 28:
2.4.2.11 DDI-X Board This board is
Page 29 and 30:
Boards Slots 1-2 CPU Slot PowerCPU
Page 31 and 32:
3.1 Software Licence Management 3.1
Page 33 and 34:
- Stations in the default Attendant
Page 35 and 36:
Controlled services Relevant softwa
Page 37 and 38:
Controlled services Number of activ
Page 39 and 40:
Controlled services TAPI 2.1 SERVER
Page 41 and 42:
egistration is accepted but the set
Page 43 and 44:
2 access on CPU III main, 16 access
Page 45 and 46:
3.4.16.2 Call accounting over IP Th
Page 47 and 48:
This license item is a global param
Page 49 and 50:
4.1 Presentation 4.1.1 Location of
Page 51 and 52:
4.1.2 Environment 4.1.2.1 Climatic
Page 53 and 54:
- 1 to 16: connecting analog Z term
Page 55 and 56:
4.2.1.4 Connecting Terminals 4.2.1.
Page 57 and 58:
4.2.1.5 Connection to the Public Ne
Page 59 and 60:
4.2.1.5.2 Digital Public Network by
Page 61 and 62:
4.2.1.5.4 Analog Public Network - D
Page 63 and 64:
Audio Input Characteristics: Input
Page 65 and 66:
4.2.1.7.6 Connecting a Doorphone 2
Page 67 and 68:
4.2.1.7.7 Using the 12V Output The
Page 69 and 70:
delivered with inter-battery connec
Page 71 and 72:
lack) and that there is no cable co
Page 73 and 74:
1. Ensure that the ON/OFF switch on
Page 75 and 76:
1. Stop the Alcatel-Lucent OmniPCX
Page 77 and 78:
2. Insert the batteries in the open
Page 79 and 80:
Note: If a hard disk is installed o
Page 81 and 82:
For performance and safety reasons,
Page 83 and 84:
Connecting the set This section des
Page 85 and 86:
The DHCP offer provides the followi
Page 87 and 88:
Displayed Status Set not connected
Page 89 and 90:
2. Connect the set, refer to Connec
Page 91 and 92:
- Proprietary Dynamic: the set acce
Page 93 and 94:
5. Select Loudspeaker 6. If your de
Page 95 and 96:
Country Type Brazil Costa-Rica Guat
Page 97 and 98:
This module presents all the action
Page 99 and 100:
For dynamic commissioning, operatio
Page 101 and 102:
- In the ALU IP Phones: DHCP IP Ran
Page 103 and 104:
Set unregistered SIP registration O
Page 105 and 106:
- Subnet mask (if no DHCP server is
Page 107 and 108:
Figure 4.44: Alcatel-Lucent IP Touc
Page 109 and 110:
You do not use a DHCP server Static
Page 111 and 112:
In the procedure below, it is assum
Page 113 and 114:
- Connect an IP Touch set to the LA
Page 115 and 116:
Static 1. Connect the power supply.
Page 117 and 118:
The 3.5 mm female jack can receive
Page 119 and 120: Figure 4.46: Alcatel-Lucent 4019 Di
Page 121 and 122: - Connect optional equipment - Prog
Page 123 and 124: - F1/F2 keys - Add-On Module keys (
Page 125 and 126: 4.7.1.2.2 ECM 4.7.1.2.3 V24 & CTI -
Page 127 and 128: The V24/CTI Interface Module is con
Page 129 and 130: 4.8.1.1 Overview The AP Interface M
Page 131 and 132: 4.8.2.2 Jumper The jumper in a gray
Page 133 and 134: 6 Not used Analog device socket: Pi
Page 135 and 136: 4.9.1.2.3 ISDN - EN55022: Limits an
Page 137 and 138: The S0 module is connected to: Figu
Page 139 and 140: 8 Not used Power supply socket: Pin
Page 141 and 142: Take as an example a building with
Page 143 and 144: Figure 4.67: ARI Number Note 1: The
Page 145 and 146: Once the IBS finishes the downloadi
Page 147 and 148: 2 1926.875 3 1925.625 4 1924.375 5
Page 149 and 150: Square zone Rectangular zone Exampl
Page 151 and 152: Important: An IP-DECT system cannot
Page 153 and 154: 4.12.2 Additional Information 4.12.
Page 155 and 156: then pull it out). - Plug in the li
Page 157 and 158: List of abbreviations - TD: Transmi
Page 159 and 160: 4.14 Extending Your Installation 4.
Page 161 and 162: Permanent replacement The default c
Page 163 and 164: - 0,5 mm cable: 505 m - 0.6 mm cabl
Page 165 and 166: RJ45 pin 1 2 3 4 5 6 7 8 MAIN: TX+
Page 167 and 168: emove CoCPUs). 3. Use LOLA to save
Page 169: 4.15.1.3.3 Hardware 4.15.1.4 Licens
Page 173 and 174: To check if the versions of Exchang
Page 175 and 176: 4.15.1.7.5 Dialing Rules My IC Soci
Page 177 and 178: 4.16 ACD applications 4.16.1 Platfo
Page 179 and 180: 5.1 Detailed description 5.1.1 Defa
Page 181 and 182: Figure 5.2: Virtual Key Functions f
Page 183 and 184: Figure 5.4: Virtual and Physical Ad
Page 185 and 186: Figure 5.6: [US only] Virtual Key F
Page 187 and 188: Figure 5.8: Virtual Key Functions f
Page 189 and 190: Figure 5.10: [US only] Virtual Key
Page 191 and 192: There are 10 pages of virtual keys
Page 193 and 194: 6.1 System Startup from a Phone Set
Page 195 and 196: _dne-egnahc_ _nigeb-egnahc_ This s
Page 197 and 198: _dne-egnahc_ _nigeb-egnahc_ _dne-eg
Page 199 and 200: _nigeb-egnahc_ _dne-egnahc_ _nigeb-
Page 201 and 202: The direct number includes up to 8
Page 203 and 204: This function is used to indicate t
Page 205 and 206: This is used to make secure data tr
Page 207 and 208: 6.2.1 Overview OMC is the PC applic
Page 209 and 210: The default IP address for the main
Page 211 and 212: ISDN 64 to 128 KPBS modems handling
Page 213 and 214: Follow the procedures described in
Page 215 and 216: - Enter the New Password - Confirm
Page 217 and 218: Remark: If you select immediate swi
Page 219 and 220: - Call groups - Broadcast groups -
Page 221 and 222:
- An Installation Wizard to help in
Page 223 and 224:
7.1 Maintenance Level 1 7.1.1 Maint
Page 225 and 226:
from your body. When holding a boar
Page 227 and 228:
7.1.1.6.2 Storage - Always wear a d
Page 229 and 230:
8.1 A ACD Automatic Call Distributi
Page 231 and 232:
8.4 D DAP DECT Access Point DASS2 D
Page 233 and 234:
Internet Protocol Security. Standar
Page 235 and 236:
POP3 Post Office Protocol. Standard
Page 237 and 238:
TERMINAL GROUP Series of terminals
show all

Installation Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?