MIC1462 manual.pdf

More documents

Recommendations

Info

The main dimensions of the instrument are shown below. FIGURE 2-2 Main Dimensions 100 mm (3.94 in.) 96 mm (3.78 in) Side View 96 mm (3.78 in.) 10 mm (0.39 in.) Max. Panel Thickness 6.0mm (.25 inches) To panel-mount the instrument: 1. Insert the rear of the instrument housing through the cutout (from the front of the mounting panel) and hold the instrument lightly in position against the panel. Ensure that the panel gasket is not distorted and that the instrument is positioned squarely against the mounting panel. Apply pressure to the front panel bezel only. Caution: Do not remove the panel gasket, as this may result in inadequate clamping of the instrument in the panel. 2. Slide the fixing strap in place (Figure 2-3) and push it forward until it is firmly in contact with the rear face of the mounting panel (the tongues on the strap should have engaged in matching rachet positions on the instrument housing and the fixing strap springs should be pushing firmly against the mounting panel rear face). MIC 1462 Manual 4 Edition 1
Once the instrument is installed in its mounting panel, it may be subsequently removed from its housing, if necessary, as described in Appendix B. FIGURE 2-3 Panel-Mounting the Instrument Mounting Clamp Controller Housing 2.3 PREPARATION FOR WIRING Electrical noise is a phenomenon typical of industrial environments. The following are guidelines that must be followed to minimize the effect of noise upon any instrumentation. 2.3.1 INSTALLATION CONSIDERATIONS Listed below are some of the common sources of electrical noise in the industrial environment: • Ignition Transformers • Arc Welders • Mechanical contact relay(s) • Solenoids Tongues on mounting clamp engage in ratchet slots on controller housing Edition 1 5 MIC 1462 Manual
Page 1 and 2: MIC 1462 1/4 DIN SETPOINT PROGRAMME
Page 3 and 4: Table of Contents Section 1 - Gener
Page 5 and 6: Figures Figure 1-1 Front Panel 2 Fi
Page 7 and 8: Section 1 - General 1.1 PRODUCT DES
Page 9: Section 2 - Installation & Wiring 2
Page 13 and 14: The only wires that should run toge
Page 15 and 16: 2.3.5 SENSOR PLACEMENT (THERMOCOUPL
Page 17 and 18: FIGURE 2-6A REMOTE INPUTS R0 R1 R2
Page 19 and 20: FIGURE 2-7A 24V Nominal AC/DC Suppl
Page 21 and 22: FIGURE 2-12 Remote Digital Communic
Page 23 and 24: FIGURE 2-18 mADC Output 2 (Control
Page 25 and 26: FIGURE 2-24 End of Program Output C
Page 27 and 28: precedence over the corresponding f
Page 29 and 30: Section 3 - Operation 3.1 POWER UP
Page 31 and 32: 3.3 INDICATORS Control Status Indic
Page 33 and 34: 3.6 VIEWING PROGRAM AND CONTROLLER
Page 35 and 36: 3.9 BASE MODE AND OFF MODE OUTPUTS
Page 37 and 38: To de-activate the Pre-Tune facilit
Page 39 and 40: 4.2 HARDWARE DEFINITION CODE This p
Page 41 and 42: Press the SCROLL key to change the
Page 43 and 44: MESSAGE AVAILABLE STEP DESCRIPTION
Page 47 and 48: Notes on Configuration Mode Paramet
Page 49 and 50: 5.1 TUNE PARAMETERS The Controller
Page 51 and 52: 11 Manual Reset (3) Man Rset Bias a
Page 53 and 54: FIGURE 5-1 Output Power (%) Output
Page 55 and 56: Section 6 - Alarm Mode The Alarm Mo
Page 57 and 58: 4d Deviation DeAlarm 1 If Alarm 1 i
Page 61 and 62:
FIGURE 6-1 Edition 1 55 MIC 1462 Ma
Page 63 and 64:
FIGURE 6.2 Edition 1 57 MIC 1462 Ma
Page 65 and 66:
7.2 PARAMETERS COMMON TO ALL PROFIL
Page 67 and 68:
does not appear program runif recov
Page 69 and 70:
MESSAGE AVAILABLE STEP DESCRIPTION
Page 71 and 72:
This parameter sequence may be view
Page 73 and 74:
MESSAGE AVAILABLE STEP DESCRIPTION
Page 75 and 76:
7.5 USING JOIN, REPEAT AND END SEGM
Page 77 and 78:
Now, with Program 2 set to perform
Page 79 and 80:
8.4 JUMPING TO THE NEXT SEGMENT At
Page 81 and 82:
8.8 ACCESSING MODES OF THE CONTROLL
Page 83 and 84:
Section 10 - Calibration Mode To en
Page 85 and 86:
TABLE 10.1 Universal Input Type Sel
Page 87 and 88:
Appendix A - Range Codes The input
Page 89 and 90:
Appendix B - Board Layout, Jumper P
Page 91 and 92:
FIGURE B-3 CPU PWA LJ3 LJ2 LJ1 IC6
Page 93 and 94:
FIGURE B-5 PWA WITH DC OUTPUT 1 TX1
Page 95 and 96:
Appendix C - Specifications INPUT S
Page 97 and 98:
Isolation: SSR Driver/TTL Drive Cap
Page 99 and 100:
Alarms Maximum Number: Maximum # Ou
Page 101 and 102:
Performance Under Reference Conditi
Page 103 and 104:
PHYSICAL Dimensions: Mounting: 1/4
Page 105 and 106:
Appendix E - Software Reference She
Page 107 and 108:
Tune Mode Inp Cor Po1 Po2 P. Out HI
Page 109 and 110:
Program Define Mode (All Programs)
Page 111 and 112:
Warranty and Return Statement These
show all

MIC1462 manual.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?