MIC1462 manual.pdf

More documents

Recommendations

Info

FIGURE B-4 PS PWA WITH RELAY OR SSR OUTPUT 1 TX1 LJ6 LJ7 SK3 LJ5 LJ4 Output Type Relay LJ4, LJ5 Jumper Position LJ5 LJ6, LJ7 Jumper Position LJ6 SSR LJ4 LJ7 MIC 1462 Manual 86 Edition 1
FIGURE B-5 PWA WITH DC OUTPUT 1 TX1 LJ8 LJ9 SK3 Output Type LJ8, LJ9 Jumper Position DC (0-10V) LJ8 DC (0-20mA) LJ9 DC (0-5V) LJ8 DC (4-20mA) LJ9 Edition 1 87 MIC 1462 Manual
Page 1 and 2:
MIC 1462 1/4 DIN SETPOINT PROGRAMME
Page 3 and 4:
Table of Contents Section 1 - Gener
Page 5 and 6:
Figures Figure 1-1 Front Panel 2 Fi
Page 7 and 8:
Section 1 - General 1.1 PRODUCT DES
Page 9 and 10:
Section 2 - Installation & Wiring 2
Page 11 and 12:
Once the instrument is installed in
Page 13 and 14:
The only wires that should run toge
Page 15 and 16:
2.3.5 SENSOR PLACEMENT (THERMOCOUPL
Page 17 and 18:
FIGURE 2-6A REMOTE INPUTS R0 R1 R2
Page 19 and 20:
FIGURE 2-7A 24V Nominal AC/DC Suppl
Page 21 and 22:
FIGURE 2-12 Remote Digital Communic
Page 23 and 24:
FIGURE 2-18 mADC Output 2 (Control
Page 25 and 26:
FIGURE 2-24 End of Program Output C
Page 27 and 28:
precedence over the corresponding f
Page 29 and 30:
Section 3 - Operation 3.1 POWER UP
Page 31 and 32:
3.3 INDICATORS Control Status Indic
Page 33 and 34:
3.6 VIEWING PROGRAM AND CONTROLLER
Page 35 and 36:
3.9 BASE MODE AND OFF MODE OUTPUTS
Page 37 and 38:
To de-activate the Pre-Tune facilit
Page 39 and 40:
4.2 HARDWARE DEFINITION CODE This p
Page 41 and 42: Press the SCROLL key to change the
Page 43 and 44: MESSAGE AVAILABLE STEP DESCRIPTION
Page 47 and 48: Notes on Configuration Mode Paramet
Page 49 and 50: 5.1 TUNE PARAMETERS The Controller
Page 51 and 52: 11 Manual Reset (3) Man Rset Bias a
Page 53 and 54: FIGURE 5-1 Output Power (%) Output
Page 55 and 56: Section 6 - Alarm Mode The Alarm Mo
Page 57 and 58: 4d Deviation DeAlarm 1 If Alarm 1 i
Page 61 and 62: FIGURE 6-1 Edition 1 55 MIC 1462 Ma
Page 63 and 64: FIGURE 6.2 Edition 1 57 MIC 1462 Ma
Page 65 and 66: 7.2 PARAMETERS COMMON TO ALL PROFIL
Page 67 and 68: does not appear program runif recov
Page 71 and 72: This parameter sequence may be view
Page 75 and 76: 7.5 USING JOIN, REPEAT AND END SEGM
Page 77 and 78: Now, with Program 2 set to perform
Page 79 and 80: 8.4 JUMPING TO THE NEXT SEGMENT At
Page 81 and 82: 8.8 ACCESSING MODES OF THE CONTROLL
Page 83 and 84: Section 10 - Calibration Mode To en
Page 85 and 86: TABLE 10.1 Universal Input Type Sel
Page 87 and 88: Appendix A - Range Codes The input
Page 89 and 90: Appendix B - Board Layout, Jumper P
Page 91: FIGURE B-3 CPU PWA LJ3 LJ2 LJ1 IC6
Page 95 and 96: Appendix C - Specifications INPUT S
Page 97 and 98: Isolation: SSR Driver/TTL Drive Cap
Page 99 and 100: Alarms Maximum Number: Maximum # Ou
Page 101 and 102: Performance Under Reference Conditi
Page 103 and 104: PHYSICAL Dimensions: Mounting: 1/4
Page 105 and 106: Appendix E - Software Reference She
Page 107 and 108: Tune Mode Inp Cor Po1 Po2 P. Out HI
Page 109 and 110: Program Define Mode (All Programs)
Page 111 and 112: Warranty and Return Statement These
show all

MIC1462 manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?