MIC1462 manual.pdf

More documents

Recommendations

Info

4.3 CONFIGURATION MODE PARAMETERS The Configuration Mode parameters are presented for view/edit in the following sequence: MESSAGE AVAILABLE STEP DESCRIPTION DISPLAY FUNCTION SETTING 1 Primary Input Input Code display- See App. A Range 5 ed defines input type/ range (see App. A) 2 Control Action Control Specifies dir - Direct control Acting action of rEV- Reverse Output 1 1 Acting *Mdr-Motor Drive Reverse * Not available if Output 1 AND Output 2 are Not Relay Outputs *Mdd-Motor Drive Direct 3 Output 2 Usage Out2 Use Specifies out2-Control use of Output Output 2 2 A2_d-Alarm 1 (direct) A2_r-Alarm 2 NOTE: This parameter not available if Control Action is set to Mdr or Mdd-Output 2 automatically used as control output (reverse) Or_d-Alarm 1 OR 2 (direct) Or_r-Alarm 1 OR 2 (reverse) Ad_d-Alarm 1 AND 2 (direct) Ad_r-Alarm 1 AND 2 (reverse) MIC 1462 Manual 36 Edition 1
MESSAGE AVAILABLE STEP DESCRIPTION DISPLAY FUNCTION SETTINGS LP_d-Loop Alarm (direct) LP_r-Loop Alarm (reverse) 4 Output 3 Useage Out3 Use Specifies Al_d-Alarm 1 use of (direct) Output 3 3 Al_r-Alarm 1 (reverse) Or_d-Alarm 1 OR 2 (direct) Or_r-Alarm 1 OR 2 (reverse) Ad_d-Alarm 1 AND 2 (direct) Ad_r-Alarm 1 AND 2 (reverse) LP_d-Loop Alarm (direct) LP_r-Loop Alarm (reverse) rEcS-Rcdr Output (SP) rEcP-Rcdr Output (PV) Edition 1 37 MIC 1462 Manual
Page 1 and 2: MIC 1462 1/4 DIN SETPOINT PROGRAMME
Page 3 and 4: Table of Contents Section 1 - Gener
Page 5 and 6: Figures Figure 1-1 Front Panel 2 Fi
Page 7 and 8: Section 1 - General 1.1 PRODUCT DES
Page 9 and 10: Section 2 - Installation & Wiring 2
Page 11 and 12: Once the instrument is installed in
Page 13 and 14: The only wires that should run toge
Page 15 and 16: 2.3.5 SENSOR PLACEMENT (THERMOCOUPL
Page 17 and 18: FIGURE 2-6A REMOTE INPUTS R0 R1 R2
Page 19 and 20: FIGURE 2-7A 24V Nominal AC/DC Suppl
Page 21 and 22: FIGURE 2-12 Remote Digital Communic
Page 23 and 24: FIGURE 2-18 mADC Output 2 (Control
Page 25 and 26: FIGURE 2-24 End of Program Output C
Page 27 and 28: precedence over the corresponding f
Page 29 and 30: Section 3 - Operation 3.1 POWER UP
Page 31 and 32: 3.3 INDICATORS Control Status Indic
Page 33 and 34: 3.6 VIEWING PROGRAM AND CONTROLLER
Page 35 and 36: 3.9 BASE MODE AND OFF MODE OUTPUTS
Page 37 and 38: To de-activate the Pre-Tune facilit
Page 39 and 40: 4.2 HARDWARE DEFINITION CODE This p
Page 41: Press the SCROLL key to change the
Page 45 and 46: MESSAGE AVAILABLE STEP DESCRIPTION
Page 47 and 48: Notes on Configuration Mode Paramet
Page 49 and 50: 5.1 TUNE PARAMETERS The Controller
Page 51 and 52: 11 Manual Reset (3) Man Rset Bias a
Page 53 and 54: FIGURE 5-1 Output Power (%) Output
Page 55 and 56: Section 6 - Alarm Mode The Alarm Mo
Page 57 and 58: 4d Deviation DeAlarm 1 If Alarm 1 i
Page 61 and 62: FIGURE 6-1 Edition 1 55 MIC 1462 Ma
Page 63 and 64: FIGURE 6.2 Edition 1 57 MIC 1462 Ma
Page 65 and 66: 7.2 PARAMETERS COMMON TO ALL PROFIL
Page 67 and 68: does not appear program runif recov
Page 71 and 72: This parameter sequence may be view
Page 75 and 76: 7.5 USING JOIN, REPEAT AND END SEGM
Page 77 and 78: Now, with Program 2 set to perform
Page 79 and 80: 8.4 JUMPING TO THE NEXT SEGMENT At
Page 81 and 82: 8.8 ACCESSING MODES OF THE CONTROLL
Page 83 and 84: Section 10 - Calibration Mode To en
Page 85 and 86: TABLE 10.1 Universal Input Type Sel
Page 87 and 88: Appendix A - Range Codes The input
Page 89 and 90: Appendix B - Board Layout, Jumper P
Page 91 and 92: FIGURE B-3 CPU PWA LJ3 LJ2 LJ1 IC6
Page 93 and 94:
FIGURE B-5 PWA WITH DC OUTPUT 1 TX1
Page 95 and 96:
Appendix C - Specifications INPUT S
Page 97 and 98:
Isolation: SSR Driver/TTL Drive Cap
Page 99 and 100:
Alarms Maximum Number: Maximum # Ou
Page 101 and 102:
Performance Under Reference Conditi
Page 103 and 104:
PHYSICAL Dimensions: Mounting: 1/4
Page 105 and 106:
Appendix E - Software Reference She
Page 107 and 108:
Tune Mode Inp Cor Po1 Po2 P. Out HI
Page 109 and 110:
Program Define Mode (All Programs)
Page 111 and 112:
Warranty and Return Statement These
show all

MIC1462 manual.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?