MIC1462 manual.pdf

More documents

Recommendations

Info

FIGURE B-6 OPTION PWA DC OUTPUT 2/OUTPUT 3 LJ9 LJ8 Output Type DC (0-10V) DC (0-20mA) LJ8, LJ9 Jumper Position LJ8 LJ9 DC (0-5V) LJ8 DC (4-20mA) LJ9 MIC 1462 Manual 88 Edition 1
Appendix C - Specifications INPUT SPECIFICATIONS General Input Sample Rate: Four per second Input Resolution: 14 bits approximately Input Impedance: Greater than 100M ohm resistive (except for DC mA and V inputs) Isolation: Universal input isolated from all outputs except SSR at 240 VAC. Thermocouple Types: Calibration: Sensor Break Protection: RTD and DC mV Type and Connection: Calibration: Lead Compensation: RTD Current: Sensor Break Protection: R, S, J, T, K, L, B, and N Complies with BS4937, NBS125 and IEC584. Break detected within 2 seconds. Control outputs set to OFF (0% power); alarms operate as if the process variable has gone over-range. Three-wire Pt100 Complies with BS1904 and DIN43760. Automatic 150uA (approximately) Break detected within 2 seconds. Control outputs set to OFF (0% power); alarms operate as if the process variable has gone under-range. DC mA and DC V Scale Range Maximum: -1999 to 9999 Scale Range Minimum: -1999 to 9999 Minimum Span: 1 display LSD Sensor Break Protection: Applicable to 4-20mA, 1-5V, and 2-10V ranges only. Break detected within 2 seconds. Control outputs set to OFF (0% power); alarms operate as if the process variable has gone under-range. Edition 1 89 MIC 1462 Manual
Page 1 and 2:
MIC 1462 1/4 DIN SETPOINT PROGRAMME
Page 3 and 4:
Table of Contents Section 1 - Gener
Page 5 and 6:
Figures Figure 1-1 Front Panel 2 Fi
Page 7 and 8:
Section 1 - General 1.1 PRODUCT DES
Page 9 and 10:
Section 2 - Installation & Wiring 2
Page 11 and 12:
Once the instrument is installed in
Page 13 and 14:
The only wires that should run toge
Page 15 and 16:
2.3.5 SENSOR PLACEMENT (THERMOCOUPL
Page 17 and 18:
FIGURE 2-6A REMOTE INPUTS R0 R1 R2
Page 19 and 20:
FIGURE 2-7A 24V Nominal AC/DC Suppl
Page 21 and 22:
FIGURE 2-12 Remote Digital Communic
Page 23 and 24:
FIGURE 2-18 mADC Output 2 (Control
Page 25 and 26:
FIGURE 2-24 End of Program Output C
Page 27 and 28:
precedence over the corresponding f
Page 29 and 30:
Section 3 - Operation 3.1 POWER UP
Page 31 and 32:
3.3 INDICATORS Control Status Indic
Page 33 and 34:
3.6 VIEWING PROGRAM AND CONTROLLER
Page 35 and 36:
3.9 BASE MODE AND OFF MODE OUTPUTS
Page 37 and 38:
To de-activate the Pre-Tune facilit
Page 39 and 40:
4.2 HARDWARE DEFINITION CODE This p
Page 41 and 42:
Press the SCROLL key to change the
Page 43 and 44: MESSAGE AVAILABLE STEP DESCRIPTION
Page 47 and 48: Notes on Configuration Mode Paramet
Page 49 and 50: 5.1 TUNE PARAMETERS The Controller
Page 51 and 52: 11 Manual Reset (3) Man Rset Bias a
Page 53 and 54: FIGURE 5-1 Output Power (%) Output
Page 55 and 56: Section 6 - Alarm Mode The Alarm Mo
Page 57 and 58: 4d Deviation DeAlarm 1 If Alarm 1 i
Page 61 and 62: FIGURE 6-1 Edition 1 55 MIC 1462 Ma
Page 63 and 64: FIGURE 6.2 Edition 1 57 MIC 1462 Ma
Page 65 and 66: 7.2 PARAMETERS COMMON TO ALL PROFIL
Page 67 and 68: does not appear program runif recov
Page 71 and 72: This parameter sequence may be view
Page 75 and 76: 7.5 USING JOIN, REPEAT AND END SEGM
Page 77 and 78: Now, with Program 2 set to perform
Page 79 and 80: 8.4 JUMPING TO THE NEXT SEGMENT At
Page 81 and 82: 8.8 ACCESSING MODES OF THE CONTROLL
Page 83 and 84: Section 10 - Calibration Mode To en
Page 85 and 86: TABLE 10.1 Universal Input Type Sel
Page 87 and 88: Appendix A - Range Codes The input
Page 89 and 90: Appendix B - Board Layout, Jumper P
Page 91 and 92: FIGURE B-3 CPU PWA LJ3 LJ2 LJ1 IC6
Page 93: FIGURE B-5 PWA WITH DC OUTPUT 1 TX1
Page 97 and 98: Isolation: SSR Driver/TTL Drive Cap
Page 99 and 100: Alarms Maximum Number: Maximum # Ou
Page 101 and 102: Performance Under Reference Conditi
Page 103 and 104: PHYSICAL Dimensions: Mounting: 1/4
Page 105 and 106: Appendix E - Software Reference She
Page 107 and 108: Tune Mode Inp Cor Po1 Po2 P. Out HI
Page 109 and 110: Program Define Mode (All Programs)
Page 111 and 112: Warranty and Return Statement These
show all

MIC1462 manual.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?