MIC1462 manual.pdf

More documents

Recommendations

Info

Each Segment in a Specific Program Final SP Time RampRate Event MIC 1462 Manual 104 Edition 1
Warranty and Return Statement These products are sold by The Partlow-West Company under the warranties set forth in the following paragraphs. Such warranties are extended only with respect to a purchase of these products, as new merchandise, directly from The Partlow-West Company or from a Partlow-West Company distributor, representative or reseller, and are extended only to the first buyer thereof who purchases them other than for the purpose of resale. Warranty These products are warranted to be free from functional defects in materials and workmanship at the time the products leave the factory and to conform at that time to the specifications set forth in the relevant instruction <strong>manual</strong> or <strong>manual</strong>s, sheet or sheets, for such products for a period of two years. THERE ARE NO EXPRESSED OR IMPLIED WARRANTIES WHICH EXTEND BEYOND THE WARRANTIES HEREIN AND ABOVE SET FORTH. PARTLOW MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCTS. Limitations The Partlow-West Company shall not be liable for any incidental damages, consequential damages, special damages, or any other damages, costs or expenses excepting only the cost or expense of repair or replacement as described above. Products must be installed and maintained in accordance with the instructions. Users are responsible for the suitability of the products to their application. There is no warranty against damage resulting from corrosion, misapplication, improper specifications or other operating condition beyond our control. Claims against carriers for damage in transit must be filed by the buyer. This warranty is void if the purchaser uses non-factory approved replacement parts and supplies or if the purchaser attempts to repair the product themselves or through a third party without ThePartlow-West Company authorization. Returns The Partlow-West Company sole and exclusive obligation and buyer’s sole and exclusive remedy under the above warranty is limited to repairing or replacing (at Partlow’s option), free of charge, the products which are reported in writing to ThePartlow-West Company at its main office indicated below. The Partlow-West Company is to be advised of return requests during normal business hours and such returns are to include a statement of the observed deficiency. The buyer shall pre-pay shipping charges for products returned and The Partlow-West Company or its representative shall pay for the return of the products to the buyer. Approved returns should be sent to: THE PARTLOW-WEST COMPANY 2 CAMPION ROAD NEW HARTFORD, NY 13413 USA MIC 1462 Manual 102 Edition 1
Page 1 and 2:
MIC 1462 1/4 DIN SETPOINT PROGRAMME
Page 3 and 4:
Table of Contents Section 1 - Gener
Page 5 and 6:
Figures Figure 1-1 Front Panel 2 Fi
Page 7 and 8:
Section 1 - General 1.1 PRODUCT DES
Page 9 and 10:
Section 2 - Installation & Wiring 2
Page 11 and 12:
Once the instrument is installed in
Page 13 and 14:
The only wires that should run toge
Page 15 and 16:
2.3.5 SENSOR PLACEMENT (THERMOCOUPL
Page 17 and 18:
FIGURE 2-6A REMOTE INPUTS R0 R1 R2
Page 19 and 20:
FIGURE 2-7A 24V Nominal AC/DC Suppl
Page 21 and 22:
FIGURE 2-12 Remote Digital Communic
Page 23 and 24:
FIGURE 2-18 mADC Output 2 (Control
Page 25 and 26:
FIGURE 2-24 End of Program Output C
Page 27 and 28:
precedence over the corresponding f
Page 29 and 30:
Section 3 - Operation 3.1 POWER UP
Page 31 and 32:
3.3 INDICATORS Control Status Indic
Page 33 and 34:
3.6 VIEWING PROGRAM AND CONTROLLER
Page 35 and 36:
3.9 BASE MODE AND OFF MODE OUTPUTS
Page 37 and 38:
To de-activate the Pre-Tune facilit
Page 39 and 40:
4.2 HARDWARE DEFINITION CODE This p
Page 41 and 42:
Press the SCROLL key to change the
Page 43 and 44:
MESSAGE AVAILABLE STEP DESCRIPTION
Page 45 and 46:
MESSAGE AVAILABLE STEP DESCRIPTION
Page 47 and 48:
Notes on Configuration Mode Paramet
Page 49 and 50:
5.1 TUNE PARAMETERS The Controller
Page 51 and 52:
11 Manual Reset (3) Man Rset Bias a
Page 53 and 54:
FIGURE 5-1 Output Power (%) Output
Page 55 and 56:
Section 6 - Alarm Mode The Alarm Mo
Page 57 and 58:
4d Deviation DeAlarm 1 If Alarm 1 i
Page 59 and 60: MESSAGE AVAILABLE STEP DESCRIPTION
Page 61 and 62: FIGURE 6-1 Edition 1 55 MIC 1462 Ma
Page 63 and 64: FIGURE 6.2 Edition 1 57 MIC 1462 Ma
Page 65 and 66: 7.2 PARAMETERS COMMON TO ALL PROFIL
Page 67 and 68: does not appear program runif recov
Page 71 and 72: This parameter sequence may be view
Page 75 and 76: 7.5 USING JOIN, REPEAT AND END SEGM
Page 77 and 78: Now, with Program 2 set to perform
Page 79 and 80: 8.4 JUMPING TO THE NEXT SEGMENT At
Page 81 and 82: 8.8 ACCESSING MODES OF THE CONTROLL
Page 83 and 84: Section 10 - Calibration Mode To en
Page 85 and 86: TABLE 10.1 Universal Input Type Sel
Page 87 and 88: Appendix A - Range Codes The input
Page 89 and 90: Appendix B - Board Layout, Jumper P
Page 91 and 92: FIGURE B-3 CPU PWA LJ3 LJ2 LJ1 IC6
Page 93 and 94: FIGURE B-5 PWA WITH DC OUTPUT 1 TX1
Page 95 and 96: Appendix C - Specifications INPUT S
Page 97 and 98: Isolation: SSR Driver/TTL Drive Cap
Page 99 and 100: Alarms Maximum Number: Maximum # Ou
Page 101 and 102: Performance Under Reference Conditi
Page 103 and 104: PHYSICAL Dimensions: Mounting: 1/4
Page 105 and 106: Appendix E - Software Reference She
Page 107 and 108: Tune Mode Inp Cor Po1 Po2 P. Out HI
Page 109: Program Define Mode (All Programs)
show all

MIC1462 manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?