Cisco IOS Wide-Area Networking Configuration Guide - Free Books

More documents

Recommendations

Info

Frame Relay Configuration ExamplesConfiguring Frame RelayFigure 32Frame Relay DCE ConfigurationFrame RelaynetworkRouter ARouter CS2 NNINNI S2200200DCE S1S1 DCE100 300DTEDTERouter BRouter D62866Configuration for Router Aframe-relay switching!interface serial 1no ip addressencapsulation frame-relayframe-relay intf-type dceframe-relay lmi-type ansiframe-relay route 100 interface serial 2 200!interface serial 2no ip addressencapsulation frame-relayframe-relay intf-type nniframe-relay lmi-type q933aframe-relay route 200 interface serial 1 100clockrate 2048000!Configuration for Router Cframe-relay switching!interface serial 1no ip addressencapsulation frame-relayframe-relay intf-type dceframe-relay route 300 interface serial 2 200!interface serial 2no ip addressencapsulation frame-relayframe-relay intf-type nniframe-relay lmi-type q933aframe-relay route 200 interface serial 1 300!62
Configuring Frame RelayFrame Relay Configuration ExamplesHybrid DTE/DCE PVC Switching ExampleRouters can be configured as hybrid DTE/DCE Frame Relay switches, as shown in Figure 33.Figure 33Hybrid DTE/DCE PVC SwitchingRouter DDTEFrame Relaynetwork301103DTES3302203Router ADTEDCEDCES2S1 Router B102 201Router C62865The following example shows one router configured with both DCE and DTE interfaces (router B actsas a hybrid DTE/DCE Frame Relay switch). It can switch frames between two DCE ports and betweena DCE port and a DTE port. Traffic from the Frame Relay network can also be terminated locally. In theexample, three PVCs are defined as follows:• Serial 1, DLCI 102, to serial 2, DLCI 201—DCE switching• Serial 1, DLCI 103, to serial 3, DLCI 301—DCE/DTE switching• Serial 2, DLCI 203, to serial 3, DLCI 302—DCE/DTE switchingDLCI 400 is also defined for locally terminated traffic.Configuration for Router Bframe-relay switching!interface ethernet 0ip address 131.108.123.231 255.255.255.0!interface ethernet 1ip address 131.108.5.231 255.255.255.0!interface serial 0no ip addressshutdown :Interfaces not in use may be shut down; shut down is not required.!interface serial 1no ip addressencapsulation frame-relayframe-relay intf-type dceframe-relay route 102 interface serial 2 201frame-relay route 103 interface serial 3 301!63
Page 1 and 2:
Cisco IOS Wide-Area NetworkingConfi
Page 4 and 5:
Documentation ConventionsAbout Cisc
Page 6 and 7:
Documentation OrganizationAbout Cis
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Additional Resources and Documentat
Page 16 and 17:
Using the CLIUsing the Command-Line
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Saving Changes to a ConfigurationUs
Page 28 and 29:
Additional InformationUsing the Com
Page 31 and 32:
Configuring Frame RelayFeature Hist
Page 33 and 34:
Configuring Frame RelayFrame Relay
Page 35 and 36:
Configuring Frame RelayConfiguring
Page 37 and 38:
Page 39 and 40:
Page 41 and 42: Configuring Frame RelayConfiguring
Page 57 and 58: Configuring Frame RelayCustomizing
Page 81 and 82: Configuring Frame RelayFrame Relay
Page 91: Configuring Frame RelayFrame Relay
Page 107 and 108: Adaptive Frame Relay Traffic Shapin
Page 115 and 116: Frame Relay 64-Bit CountersFeature
Page 117 and 118: Frame Relay 64-Bit CountersSupporte
Page 119 and 120: Frame Relay 64-Bit CountersConfigur
Page 121 and 122: Frame Relay 64-Bit CountersConfigur
Page 123 and 124: Frame Relay MIB EnhancementsFeature
Page 125 and 126: • The chapter “Configuring Simp
Page 127: Command ReferenceThe following comm
Page 130 and 131: Feature OverviewFrame Relay Point-M
Page 132 and 133: Supported Standards, MIBs, and RFCs
Page 134 and 135: Configuration ExamplesFrame Relay P
Page 136 and 137: Command ReferenceFrame Relay Point-
Page 138 and 139: How Frame Relay Queueing and Fragme
Page 140: • Cisco 2500 series• Cisco 2600
Page 143 and 144:
Configuring the Shaping Policy Usin
Page 145 and 146:
The following sample output for the
Page 147 and 148:
Frame Relay Queueing, Shaping, and
Page 149 and 150:
Frame Relay PVC Bundles with QoS Su
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Frame Relay Voice-Adaptive Traffic
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
MQC-Based Frame Relay Traffic Shapi
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Multilink Frame Relay (FRF.16.1)Fir
Page 205 and 206:
Multilink Frame Relay (FRF.16.1)Inf
Page 207 and 208:
Multilink Frame Relay (FRF.16.1)How
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Multilink Frame Relay (FRF.16.1)Con
Page 215 and 216:
Multilink Frame Relay (FRF.16.1)Com
Page 217 and 218:
Distributed Multilink Frame Relay (
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Configuring Frame Relay-ATM Interwo
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Layer 2 Tunnel Protocol Version 3Fi
Page 241 and 242:
Supported Port Adapters for the Cis
Page 243 and 244:
• In OAM local emulation mode onl
Page 245 and 246:
Layer Frame Fragmentation Restricti
Page 247 and 248:
With ISIS packet fragmentation, ISI
Page 249 and 250:
• Policing on both Ethernet and A
Page 251 and 252:
L2TPv3 DecapsulationWhen an L2TPv3
Page 253 and 254:
• Configuring output access contr
Page 255 and 256:
Table 3Engine 5 Interfaces Supporte
Page 257 and 258:
Table 4L2TPv3 Features Supported in
Page 259 and 260:
Table 4L2TPv3 Features Supported in
Page 261 and 262:
Frame Relay-Specific Restrictions
Page 263 and 264:
• FRF.9 process switched payload
Page 265 and 266:
• Egress queueing is determined a
Page 267 and 268:
Information About Layer 2 Tunnel Pr
Page 269 and 270:
Benefits of Using L2TPv3L2TPv3 Simp
Page 271 and 272:
Static L2TPv3 SessionsTypically, th
Page 273 and 274:
L2TPv3 Type of Service MarkingKeepa
Page 275 and 276:
configured with the L2TPv3 Control
Page 277 and 278:
L2TPv3 Protocol DemultiplexingThe P
Page 279 and 280:
Supported L2TPv3 PayloadsL2TPv3 sup
Page 281 and 282:
CIR GuaranteesTo provide committed
Page 283 and 284:
Table 6Release Support for the ATM
Page 285 and 286:
Figure 3Protocol Demultiplexing of
Page 287 and 288:
This task configures a set of timin
Page 289 and 290:
Table 8Compatibility Matrix for L2T
Page 291 and 292:
Step 5Step 6Command or Actionpasswo
Page 293 and 294:
Step 5Step 6Command or Actiondigest
Page 295 and 296:
Step 6Step 7Command or Actionshow l
Page 297 and 298:
For simple L2TPv3 signaling configu
Page 299 and 300:
Step 7Step 8Step 9Step 10Command or
Page 301 and 302:
Step 3Step 4Command or Actioninterf
Page 303 and 304:
Step 5Step 6Step 7Step 8Command or
Page 305 and 306:
Configuring the Xconnect Attachment
Page 307 and 308:
DETAILED STEPSStep 1Step 2Command o
Page 309 and 310:
Step 5Step 6Command or Actioncell-p
Page 311 and 312:
Configuring VC Mode ATM Cell Packin
Page 313 and 314:
Configuring ATM AAL5 SDU Mode over
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Configuring Protocol Demultiplexing
Page 323 and 324:
Step 3Command or Actioninterface ty
Page 325 and 326:
Step 7Step 8Command or Actionxconne
Page 327 and 328:
DETAILED STEPSStep 1Step 2enableExa
Page 329 and 330:
Configuring a Negotiated L2TPv3 Ses
Page 331 and 332:
Configuring L2TPv3 Control Channel
Page 333 and 334:
Configuring ATM Single Cell Relay V
Page 335 and 336:
encapsulation aal5!interface atm 1/
Page 337 and 338:
Verifying OAM Local Emulation for A
Page 339 and 340:
Configuring QoS for L2TPv3 on the C
Page 341 and 342:
encapsulation frame-relayframe-rela
Page 343 and 344:
Note that the sample output policy
Page 345 and 346:
Configuring a QoS Policy for Commit
Page 347 and 348:
!interface Serial0/0.1/1:11encapsul
Page 349 and 350:
Technical AssistanceDescriptionThe
Page 351 and 352:
Table 912.0(24)S112.0(27)S12.0(28)S
Page 353 and 354:
Table 9Feature Information for Laye
Page 355 and 356:
MTU—maximum transmission unit. Ma
Page 357 and 358:
Configuring SMDSSMDS Hardware Requi
Page 359 and 360:
Configuring SMDSEnabling SMDS on th
Page 361 and 362:
Configuring SMDSEnabling SMDS on th
Page 363 and 364:
Configuring SMDSCustomizing Your SM
Page 365 and 366:
Configuring SMDSCustomizing Your SM
Page 367 and 368:
Configuring SMDSSMDS Configuration
Page 369 and 370:
Page 371 and 372:
Page 373:
Configuring X.25 and LAPB
Page 376 and 377:
LAPB OverviewConfiguring X.25 and L
Page 378 and 379:
LAPB Configuration Task ListConfigu
Page 380 and 381:
X.25 Configuration Task ListConfigu
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Configuring Additional X.25 Interfa
Page 390 and 391:
Configuring Additional X.25 Interfa
Page 392 and 393:
Configuring an X.25 Datagram Transp
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Configuring Additional X.25 Datagra
Page 402 and 403:
Configuring Additional X.25 Datagra
Page 404 and 405:
Configuring X.25 RoutingConfiguring
Page 406 and 407:
Configuring X.25 RoutingConfiguring
Page 408 and 409:
Configuring Additional X.25 Routing
Page 410 and 411:
Configuring Additional X.25 Routing
Page 412 and 413:
Configuring DNS-Based X.25 RoutingC
Page 414 and 415:
Configuring DNS-Based X.25 RoutingC
Page 416 and 417:
Configuring X.25 over Frame Relay (
Page 418 and 419:
Configuring Priority Queueing or Cu
Page 420 and 421:
Configuring X.25 Closed User Groups
Page 422 and 423:
Page 424 and 425:
Page 426 and 427:
Page 428 and 429:
Configuring DDN or BFE X.25Configur
Page 430 and 431:
Configuring DDN or BFE X.25Configur
Page 432 and 433:
Configuring X.25 Remote Failure Det
Page 434 and 435:
Creating X.29 Access ListsConfiguri
Page 436 and 437:
X.25 and LAPB Configuration Example
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Page 448 and 449:
Page 450 and 451:
Page 452 and 453:
Page 454 and 455:
Page 456 and 457:
Page 458 and 459:
Page 460 and 461:
Feature OverviewTerminal Line Secur
Page 462 and 463:
Feature OverviewTerminal Line Secur
Page 464 and 465:
Supported PlatformsTerminal Line Se
Page 466 and 467:
Configuration TasksTerminal Line Se
Page 468 and 469:
Command ReferenceTerminal Line Secu
Page 470 and 471:
GlossaryTerminal Line Security for
Page 472 and 473:
Supported PlatformsX.25 Annex G Ses
Page 474 and 475:
Command ReferenceX.25 Annex G Sessi
Page 476 and 477:
Feature OverviewX.25 Dual Serial Li
Page 478 and 479:
Supported PlatformsX.25 Dual Serial
Page 480 and 481:
Configuration TasksX.25 Dual Serial
Page 482 and 483:
Command ReferenceX.25 Dual Serial L
Page 484 and 485:
GlossaryX.25 Dual Serial Line Manag
Page 486 and 487:
Feature OverviewX.25 over TCP Profi
Page 488 and 489:
Supported PlatformsX.25 over TCP Pr
Page 490 and 491:
Configuration TasksX.25 over TCP Pr
Page 492 and 493:
Command ReferenceX.25 over TCP Prof
Page 494 and 495:
GlossaryX.25 over TCP Profiles10
Page 496 and 497:
When to Use Record Boundary Preserv
Page 498 and 499:
Restrictions• X.25 connections wi
Page 500 and 501:
CommandRouter(config-if)# x25 pvc c
Page 502 and 503:
successfully completed, the TCP con
Page 504 and 505:
• PVC Configured to Use RBP for I
Page 506 and 507:
X.121—ITU-T standard describing a
Page 508 and 509:
ContentsX.25 Suppression of Securit
Page 510 and 511:
How to Suppress the X.25 Security S
Page 512 and 513:
Configuration Example for Suppressi
Page 514 and 515:
Command ReferenceX.25 Suppression o
Page 516 and 517:
Information About X.25 Call Confirm
Page 518 and 519:
How to Configure X.25 Call Confirm
Page 520 and 521:
Additional ReferencesX.25 Call Conf
Page 522 and 523:
Command ReferenceX.25 Call Confirm
Page 524 and 525:
Displaying the Contents of X.25 Pac
Page 526 and 527:
Command ReferenceX.25 Data Display
Page 528 and 529:
Information About X.25 Version Conf
Page 530 and 531:
Page 532 and 533:
Page 534 and 535:
Page 536 and 537:
How to Specify the X.25 VersionX.25
Page 538 and 539:
Configuration Examples for X.25 Ver
Page 540 and 541:
Additional ReferencesX.25 Version C
Page 542 and 543:
Command ReferenceX.25 Version Confi
Page 544 and 545:
ContentsX.25 Station Type for ISDN
Page 546 and 547:
How to Configure X.25 Encapsulation
Page 548 and 549:
Additional ReferencesX.25 Station T
Page 550 and 551:
Command ReferenceX.25 Station Type
Page 553 and 554:
Frame Relay-ATM Interworking Suppor
Page 555 and 556:
X.25 Facility HandlingThis appendix
Page 557 and 558:
X.25 Facility HandlingX.25 Facility
show all

Cisco IOS Wide-Area Networking Configuration Guide - Free Books

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?