Leica GPS1200+ System Field Manual

More documents

Recommendations

Info

IF parameters forANDTHENare to be configured PARAM (F3) changes toCONFIGURE Real-Time StopCriteria. Refer to paragraph"CONFIGURE Real-Time StopCriteria".CONFIGUREPost-Process StopCriteriaDescription of fieldsThe parameters shown on this screen depend on the setting for in CONFIGURE Point Occupation Settings.Field Option DescriptionUser inputUser inputOutputUser inputSets the required observation time for eachpoint. Counting time starts when OCUPY (F1) ispressed.Sets the required number of observations thatshould be recorded at each point. Countingobservations starts when OCUPY (F1) ispressed.Displays the rate at which static raw observationsare logged as configured in CONFIGURELogging of Raw Obs.Sets the required observation time dependingon the number of satellites available. Countingtime starts when OCUPY (F1) is pressed. Thereceiver stops measuring when the set length oftime for a certain number of satellites is reached.Should the number of available satelliteschange during observation, the observationsalready recorded will be taken into account.Next stepStep Description1. CONT (F1) closes the screen.2. CONT (F1) returns to the screen from where CONFIGURE Point OccupationSettings was accessed.114 GPS1200+ Config...\Survey Settings...
CONFIGUREReal-Time StopCriteriaDescription of fieldsThe parameters shown on this screen depend on the setting for in CONFIGURE Point Occupation Settings.Field Option Description
Page 1 and 2:
Version 7.0EnglishLeica GPS1200+Sys
Page 3 and 4:
Name Description FormatSystem Field
Page 5 and 6:
10 Linework 6910.1 Performing Linew
Page 7 and 8:
26 Menu Tree 213Index 215Table of C
Page 9 and 10:
1 User Interface1.1 KeyboardKeyboar
Page 11 and 12:
1.2 ScreenScreenabcdeGPS12 129kfghi
Page 13 and 14:
AppearanceDescriptionORTap on the i
Page 15 and 16:
1.4 IconsDescriptionIcons show the
Page 17 and 18:
Real-time mode: RoverAn arrow point
Page 19 and 20:
IconDescriptionThe internal memory
Page 21 and 22:
1.5 SymbolsDescriptionFilterThe sym
Page 23 and 24:
2 Equipment Setup2.1 Receiver Ports
Page 25 and 26:
2.3 Real-Time Reference, Single Tri
Page 27 and 28:
2.5 SmartRover - External RadioUseE
Page 29 and 30:
Position of cablesin the minipackca
Page 31 and 32:
9.3 mm3 Determining Antenna Heights
Page 33 and 34:
4 Using RX12504.1 Switching between
Page 35 and 36:
4.3 Interface Configuration4.3.1 Ov
Page 37 and 38:
4.3.3 Configuring Clip-On Interface
Page 39 and 40:
5 Receiver Protection with PINDescr
Page 41 and 42:
6 Manage... - Getting StartedAccess
Page 43 and 44:
SHIFT DEFLT (F5)Available for MANAG
Page 45 and 46:
7 Manage...\Jobs7.1 OverviewDescrip
Page 47 and 48:
Next stepPAGE (F6) changes to the C
Page 49 and 50:
8 Manage...\Data8.1 OverviewDescrip
Page 51 and 52:
SHIFT INDIV (F5) or SHIFT RUN (F5)T
Page 53 and 54:
Next stepIFcreating a pointTHENSTOR
Page 55 and 56:
EDIT (F3)To view and edit the highl
Page 57 and 58:
8.3 Line/Area Management8.3.1 Overv
Page 59 and 60:
Field Option Description Choicelist
Page 61 and 62:
8.4 Point Sorting and Filters8.4.1
Page 63 and 64: 8.4.2 Point, Line and Area Code Fil
Page 65 and 66: 9 Manage...\Codelists9.1 Creating a
Page 67 and 68: NEW-A (F2)To add a new input field
Page 69 and 70: 10 Linework10.1 Performing Linework
Page 71 and 72: Field Option DescriptionReOpen AnyA
Page 73 and 74: SURVEYSurvey: Job Name,Survey pageT
Page 75 and 76: 11 Manage...\Coordinate Systems11.1
Page 77 and 78: Field Option Description Choicelist
Page 79 and 80: 11.3.2 Creating/Editing a Transform
Page 81 and 82: 11.4 Geoid/CSCS ModelsThe creation
Page 83 and 84: 12 Manage...\Configuration Sets12.1
Page 85 and 86: 12.3 Editing a Configuration SetAcc
Page 87 and 88: 13 Manage...\Antennas13.1 OverviewD
Page 89 and 90: MANAGENew Antenna,IGS pageThe combi
Page 91 and 92: 14 Convert...\Export Data from Job1
Page 93 and 94: Field Option DescriptionData, GSI o
Page 95 and 96: 14.4 Exporting LandXML DataGeneralA
Page 97 and 98: 15 Convert...\Import Data to Job15.
Page 101 and 102: 16 Convert...\Copy Points Between J
Page 103 and 104: 17 Config...\Survey Settings...17.1
Page 105 and 106: 17.2 Display SettingsDescriptionDis
Page 107 and 108: 17.3 Coding & LineworkDescriptionAc
Page 109 and 110: 17.4 Quality Control SettingsDescri
Page 111 and 112: Field Option DescriptionFrom 0.05s
Page 113: Field Option DescriptionChoicelistC
Page 117 and 118: 18 Config...\Instrument Settings...
Page 119 and 120: Field Option Description Automatic
Page 121 and 122: 18.4 Instrument IDDescriptionAccess
Page 123 and 124: 19 Config...\General Settings...19.
Page 125 and 126: 19.3 Units & FormatsDescriptionAcce
Page 127 and 128: Field Option DescriptionLat,Long or
Page 129 and 130: 19.5 Display, Beeps, TextDescriptio
Page 131 and 132: 19.6 Start Up & Power DownDescripti
Page 133 and 134: 20 Config...\Interfaces... - Genera
Page 135 and 136: 20.2 Real-Time20.2.1 OverviewDescri
Page 137 and 138: 20.2.3 Configuration of a Reference
Page 139 and 140: Field Option Description Bluetooth
Page 143 and 144: Description of fieldsField Option D
Page 145 and 146: Description of fieldsField Option D
Page 147 and 148: Field Option DescriptionLogShow and
Page 149 and 150: 20.2.6 Configuration of GGA Message
Page 151 and 152: 20.3 Hidden PointDescriptionAccessC
Page 153 and 154: Next stepStep Description1. CONT (F
Page 155 and 156: Field Option DescriptionBluetooth x
Page 157 and 158: Field Option Description User input
Page 159 and 160: 21 Configuration of Devices21.1 Ove
Page 161 and 162: Next stepCONT (F1) closes the scree
Page 163 and 164: Field Option DescriptionCRNot avail
Page 165 and 166:
22 Config...\Interfaces... - Contro
Page 167 and 168:
Description of fieldsField Option D
Page 169 and 170:
22.3 RadiosDescriptionAccessCONFIGU
Page 171 and 172:
22.5 GPRS / Internet DevicesDescrip
Page 173 and 174:
Field Option Description User input
Page 175 and 176:
Next stepStep Description1. STORE (
Page 177 and 178:
23 Tools...23.1 Format Memory Devic
Page 179 and 180:
23.3 Upload System Files...Descript
Page 181 and 182:
23.5 Licence KeysDescriptionAccessW
Page 183 and 184:
Way of workingstep-by-stepStep Desc
Page 185 and 186:
24 STATUS24.1 STATUS: Survey...24.1
Page 187 and 188:
Description of symbolsSymbolDescrip
Page 189 and 190:
FieldDescriptionAvailable for Galil
Page 191 and 192:
Name of pageRef (Nearest)pageRef (i
Page 193 and 194:
Field,,,,,DescriptionThe pseudorang
Page 195 and 196:
STATUSPosition,Speed pageDescriptio
Page 197 and 198:
STATUSLogging,Ring Buffer pageDescr
Page 199 and 200:
24.1.5 Occupation Information Statu
Page 201 and 202:
24.2 STATUS: Battery & MemoryAccess
Page 203 and 204:
24.3 STATUS: System InformationAcce
Page 205 and 206:
25 NTRIP via Internet25.1 OverviewD
Page 207 and 208:
StepTheDescriptionreceiver is now o
Page 209 and 210:
Step DescriptionHighlight Real-Time
Page 211 and 212:
StepDescription Indicates if charge
Page 213 and 214:
26 Menu TreeMenu treeMAIN MENU||—
Page 215 and 216:
IndexAAbsolute coordinate differenc
Page 217 and 218:
Ellipsoid .........................
Page 219 and 220:
Mechanical reference plane ........
Page 221 and 222:
On, off ...........................
show all

Leica GPS1200+ System Field Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?