HP BladeSystem Onboard Administrator User Guide - HP Business ...
HP BladeSystem Onboard Administrator User Guide - HP Business ...
HP BladeSystem Onboard Administrator User Guide - HP Business ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
TCP/IP Settings for Standby <strong>Onboard</strong> <strong>Administrator</strong><br />
This screen displays the current TCP/IP settings for the <strong>Onboard</strong> <strong>Administrator</strong>.<br />
IPv6 Information<br />
Field Description<br />
IPv6<br />
DHCPv6<br />
Router Advertisements<br />
General Information<br />
Field Description<br />
Status of IPv6 protocol for all <strong>Onboard</strong> <strong>Administrator</strong>, interconnect, and server iLO<br />
modules in the enclosure. Possible values are Enabled or Disabled.<br />
Status of the IP address for all <strong>Onboard</strong> <strong>Administrator</strong>, interconnect, and server iLO<br />
modules in the enclosure from a DHCP server. Possible values are Enabled or Disabled.<br />
Status of auto configuration of IPv6 addresses from Router Advertisement messages to<br />
all <strong>Onboard</strong> <strong>Administrator</strong>, interconnect, and server iLO modules in the enclosure.<br />
Possible values are Enabled or Disabled.<br />
MAC Address The <strong>Onboard</strong> <strong>Administrator</strong> MAC address. This is an informational field and cannot be<br />
changed.<br />
IP Address<br />
Static IP address for the <strong>Onboard</strong> <strong>Administrator</strong> (required if static IP settings is selected)<br />
Subnet Mask<br />
Subnet mask for the <strong>Onboard</strong> <strong>Administrator</strong> (required if static IP settings is selected)<br />
Gateway<br />
Gateway address for the <strong>Onboard</strong> <strong>Administrator</strong> (required if static IP settings is<br />
selected)<br />
DNS Server 1 The IP address for the primary DNS server<br />
DNS Server 2 The IP address for the secondary DNS server<br />
<strong>Onboard</strong> <strong>Administrator</strong> Name (DNS Host Name)—The name of the <strong>Onboard</strong> <strong>Administrator</strong>. The default for this field is the DNS host<br />
name.<br />
NIC Settings<br />
• Auto-Negotiate—Automatically configures the best link. This is the default setting. This option supports<br />
a NIC speed of 10Mb/s, 100Mbps, or 1000Mb/s. The 1000Mb/s setting is only available when<br />
Auto-Negotiate is selected.<br />
• Forced Full Duplex—Enables you to manually specify which settings the external NIC uses when trying<br />
to establish a link. The <strong>Onboard</strong> <strong>Administrator</strong> does not verify that the forced Ethernet settings are valid<br />
on the network. The loss of communications might occur if the wrong or incompatible settings are used.<br />
Forced settings take effect 3 seconds after enabling or disabling the settings. The forced option only<br />
supports NIC speeds of 10Mb/s or 100Mb/s.<br />
To modify the TCP/IP settings, select Click here.<br />
Standby <strong>Onboard</strong> <strong>Administrator</strong> Virtual Buttons tab<br />
Click Reset to reset the <strong>Onboard</strong> <strong>Administrator</strong>. A confirmation screen appears, asking if you are sure that<br />
you want to perform the action and that you are signed out and disconnected from the <strong>Onboard</strong><br />
<strong>Administrator</strong>. Click OK to proceed, or click Cancel to exit without a change.<br />
Click Toggle On/Off to change the <strong>Onboard</strong> <strong>Administrator</strong> module UID light. This identifies a particular<br />
<strong>Onboard</strong> <strong>Administrator</strong> when there are more than one.<br />
Configuring the <strong>HP</strong> <strong>BladeSystem</strong> c7000 enclosure and enclosure devices 129