HP BladeSystem Onboard Administrator User Guide - HP Business ...
HP BladeSystem Onboard Administrator User Guide - HP Business ...
HP BladeSystem Onboard Administrator User Guide - HP Business ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
• Auto-Negotiate—Automatically configures the best link. This is the default setting. This option supports<br />
a NIC speed of 10Mb/s, 100Mb/s, or 1000Mbps. The 1000Mb/s setting is only available when<br />
Auto-Negotiate is selected.<br />
• Forced Full Duplex—Enables you to manually specify which settings the external NIC uses when trying<br />
to establish a link. <strong>Onboard</strong> <strong>Administrator</strong> does not verify that the forced Ethernet settings are valid on<br />
the network. The loss of communications might occur if the wrong or incompatible settings are used.<br />
Forced settings take effect 3 seconds after enabling or disabling the settings. The forced option only<br />
supports NIC speeds of 10Mbps or 100Mb/s.<br />
• NIC Speed—Selects a NIC speed of 10Mb/s or 100Mb/s<br />
To save the new settings, click Apply.<br />
Network access<br />
Using these settings, an administrator can configure settings relating to network access to the <strong>Onboard</strong><br />
<strong>Administrator</strong>. These settings are specific to the enclosure and do not affect the network configurations for<br />
server blades.<br />
Protocol restrictions<br />
The Protocol Restrictions subcategory is used to restrict access to the <strong>Onboard</strong> <strong>Administrator</strong>. You can select<br />
up to four protocol settings to allow or restrict access to the <strong>Onboard</strong> <strong>Administrator</strong>.<br />
• Enable Web Access (HTTP/HTTPS)—This checkbox is selected by default. Clearing this checkbox<br />
disables HTTP/HTTPS access to the <strong>Onboard</strong> <strong>Administrator</strong>. Port 80 is used for HTTP, and port 443 is<br />
used for HTTPS.<br />
CAUTION: Disabling Web Access (HTTP/HTTPS) disconnects all users attached to the <strong>Onboard</strong><br />
<strong>Administrator</strong> through HTTP/HTTPS, including the administrator.<br />
• Enable Secure Shell—This checkbox is selected by default. Clearing this checkbox disables Secure Shell<br />
connections to the <strong>Onboard</strong> <strong>Administrator</strong>. SSH is disabled when Two-Factor Authentication is enabled.<br />
Disabling Two-Factor Authentication does not automatically re-enable SSH. To re-enable SSH, you must<br />
select the checkbox, and then click Apply. Port 22 is used for SSH.<br />
• Enable Telnet—This checkbox is not selected by default. Selecting this checkbox enables Telnet<br />
connections to the <strong>Onboard</strong> <strong>Administrator</strong>. Telnet is disabled when Two-Factor Authentication is<br />
enabled. Disabling Two-Factor Authentication does not automatically re-enable Telnet. To re-enable<br />
Telnet, you must select the checkbox, and then click Apply. Port 23 is used for Telnet.<br />
NOTE: When the <strong>Onboard</strong> <strong>Administrator</strong> is operating in FIPS mode ON/DEBUG, the Telnet<br />
protocol cannot be used.<br />
NOTE: Telnet is disabled after a factory reset or when Two-Factor Authentication is enabled.<br />
• Enable XML Reply—This checkbox is selected by default. This checkbox enables XML data to be shared<br />
between the <strong>Onboard</strong> <strong>Administrator</strong> and other <strong>HP</strong> management tools such as <strong>HP</strong> Systems Insight<br />
Manager. To display the information that is shared by the <strong>Onboard</strong> <strong>Administrator</strong> if this protocol is<br />
enabled, click View.<br />
• Enforce Strong Encryption—This checkbox is not selected by default. Selecting this checkbox enforces<br />
use of only FIPS140-2 approved algorithms including AES, 3DES, and SHA for SSH sessions.<br />
Configuring the <strong>HP</strong> <strong>BladeSystem</strong> c7000 enclosure and enclosure devices 83