a) b - École Polytechnique de Montréal

More documents

Recommendations

Info

PMMA Figure 2-23. TEM micrograph of a 50/50 PS/PMMA blend filled with 2 wt% CB. 2.3.1.1.2 Percolation Threshold of Carbon-Nanotube Polymer Composites Figure 2-24 clearly shows a large spread in the number of investigations for polymer/carbon nanotubes in different polymer matrices. Figure 2-24 also shows the minimum observed percolation thresholds C together with the number of publications for each polymer matrix. This study shows that for all C > 0.2 wt% of carbon nanotubes, no more than two papers could be exploited. This finding supports the belief that with optimized dispersion methods a percolation threshold C ≈ 0.1 wt% might be obtainable for nearly any CNT/polymer system(Bauhofer & Kovacs, 2009). 2.3.1.1.3 Disadvantages of Conductive Fillers, Especially Carbon Black The great majority of commercial resins are compoun<strong>de</strong>d with conductive fillers to create conductive composites. The most commonly used composite is 15–30% carbon black in polymer to make containers, trays, bags, work surfaces, wrist straps, etc. PS 54
Figure 2-24. Plot of the total number of publications per polymer system versus the minimum percolation threshold achieved with the respective system(Bauhofer & Kovacs, 2009). Figure 2-25. Resistivity of carbon black/polymer composite as a function of carbon black volume fraction(Rosner, 2000) 55
Page 1 and 2:
© Sepehr Ravati, 2010. UNIVERSITÉ
Page 3 and 4:
DEDICATED To my parents iii
Page 5 and 6:
RÉSUMÉ Cette thèse présente, po
Page 7 and 8:
devenir une structure hiérarchique
Page 9 and 10:
ABSTRACT This thesis presents, for
Page 11 and 12:
system can be increased from 10 -15
Page 13 and 14:
CONDENSÉ EN FRANÇAIS Dans ce trav
Page 15 and 16:
deuxième coquille de PS. Les phase
Page 17 and 18:
structures à percolation multiple
Page 19 and 20:
autre sous-type de morphologie dans
Page 21 and 22:
TABLE OF CONTENTS DEDICATION.......
Page 23 and 24:
xxiii 2.4.1.1.1 Charged Polymer Ads
Page 25 and 26:
5.3.4 Annealing Test ..............
Page 27 and 28:
xxvii REFERENCES ..................
Page 29 and 30:
LIST OF FIGURES xxix Figure 1-1. a)
Page 31 and 32:
Figure 2-12. SEM photomicrograph of
Page 33 and 34:
Figure 2-34. Schematic view of diff
Page 35 and 36:
Figure 4-8. SEM micrographs of vari
Page 37 and 38:
Figure 5-6. a),b) Scanning electron
Page 39 and 40:
and c) triangular concentration dia
Page 41 and 42:
n number of moles p concentration o
Page 43 and 44:
AFM atomic force microscopy LIST OF
Page 45 and 46:
PS-co-PMMA copolymer of PS and PMMA
Page 47 and 48:
1.1 Introduction CHAPTER 1 - INTROD
Page 49 and 50: Figure 1-2. Human heart, longitudin
Page 51 and 52: One of the applications for porous
Page 53 and 54: On the other hand, a novel tri-cont
Page 55 and 56: 2.1 Polymer Blends CHAPTER 2 - LITE
Page 57 and 58: Based on Sterling’s approximation
Page 59 and 60: Antonoff’s rule (Equation 2-13) i
Page 61 and 62: 2.1.2.1 Binary Polymer Blends 2.1.2
Page 63 and 64: Some other studies(Everaert, Aerts,
Page 65 and 66: where the parameter z is dependent
Page 67 and 68: “compatibilization” was suggest
Page 69 and 70: a) λ BC A and B are matrices, b) C
Page 71 and 72: Reignier & Favis, 2000, 2003a; Reig
Page 73 and 74: measure the interfacial tension of
Page 75 and 76: a) b) Figure 2-6. Dependence of the
Page 77 and 78: Omonov et al. found double percolat
Page 79 and 80: 2.1.2.2.3 Effect of Composition on
Page 81 and 82: a) b) C B A c) Figure 2-12. SEM pho
Page 83 and 84: In the case where PS is the matrix,
Page 85 and 86: Posthuma de Boer, 1999) (Kumin & Ch
Page 87 and 88: lattice, such as square lattice, wi
Page 89 and 90: magnetization, which is a function
Page 91 and 92: Polymers have long been thought of
Page 93 and 94: epoxy as a function of nanotube wei
Page 95 and 96: Figure 2-19. Approaching the percol
Page 97 and 98: Figure 2-21. Transmission electron
Page 99: Figure 2-22: Dependence of PE conti
Page 103 and 104: chain provides the conductive path
Page 105 and 106: 2.3.1.2.1 Polyaniline One of the mo
Page 107 and 108: CoPA/LLDPE/PANI blend and a poor-qu
Page 109 and 110: Narkis and co-workers extended and
Page 111 and 112: Figure 2-31: Conductivity of PVDF/P
Page 113 and 114: organic thin films, a novel and str
Page 115 and 116: on the topic have been reported in
Page 117 and 118: succeeded in creating thin films wi
Page 119 and 120: Addition of salt to the solution of
Page 121 and 122: different from that of linear homop
Page 123 and 124: Figure 2-39. Macromolecule with a)
Page 125 and 126: polyanion such as hyaluronan (HA)(P
Page 127 and 128: 2.4.1.1.7 Effect of Salt on Multila
Page 129 and 130: 2.4.1.1.8 Overcompensation of the M
Page 131 and 132: important factors determining the g
Page 133 and 134: As shown in Figure 2-44, swelling a
Page 135 and 136: increasing the pH value due to a de
Page 137 and 138: CHAPTER 3 - ORGANIZATION OF THE ART
Page 139 and 140: discussed above, HDPE, PS, PMMA, an
Page 141 and 142: CHAPTER 4 - LOW PERCOLATION THRESHO
Page 143 and 144: or model which predicts where the p
Page 145 and 146: concentration threshold for the ons
Page 147 and 148: chemical and weathering resistance,
Page 149 and 150: Table 4-1. Material Characteristics
Page 151 and 152:
filled with blend pellets. To facil
Page 153 and 154:
4.3.6 Conductivity Measurements DC
Page 155 and 156:
experimentally in this research gro
Page 157 and 158:
a) b) c) d) Figure 4-4. Schematic i
Page 159 and 160:
microstructure of the quaternary bl
Page 161 and 162:
a) b) c) d) Figure 4-6. SEM microgr
Page 163 and 164:
a) b) PVDF PS PMMA c) d) e) HDPE PS
Page 165 and 166:
Uniform layers of PS and PMMA situa
Page 167 and 168:
the concentration of HDPE is increa
Page 169 and 170:
a) b) c) e) Figure 4-11. SEM microg
Page 171 and 172:
melt-processable and contains 25 wt
Page 173 and 174:
One question that should be address
Page 175 and 176:
Conductivity(S/cm) Ternary Blend 1,
Page 177 and 178:
phase(PMMA), the concentration of P
Page 179 and 180:
(6) Virgilio, N.; Desjardins, P.; L
Page 181 and 182:
ONION MORPHOLOGY HDPE PVDF PS Contr
Page 183 and 184:
work described above has focused on
Page 185 and 186:
thermodynamic explanation to predic
Page 187 and 188:
four-point probe increases continuo
Page 189 and 190:
in the rheology tests were compress
Page 191 and 192:
5.3.6 Layer-by-Layer Deposition The
Page 193 and 194:
prepare a polymer blend structure w
Page 195 and 196:
a) b) c) Figure 5-3. Scanning elect
Page 197 and 198:
spontaneously self-assembled. After
Page 199 and 200:
a) b) c) d) e) f) g) h) Figure 5-5.
Page 201 and 202:
Since the ultra-low surface area va
Page 203 and 204:
c) a) b) Figure 5-6. a),b) Scanning
Page 205 and 206:
salt to a PSS polyelectrolyte solut
Page 207 and 208:
A relationship between macropore si
Page 209 and 210:
close together. It is interesting t
Page 211 and 212:
Figure 5-9. Mass increase (%) indic
Page 213 and 214:
In this work the conductance of the
Page 215 and 216:
deposited PANI layers increases unt
Page 217 and 218:
(52) Guo, H. F.; Packirisamy, S.; G
Page 219 and 220:
6.2 Introduction It is well-known t
Page 221 and 222:
modified version of Harkins theory(
Page 223 and 224:
6.3 Experimental 6.3.1 Materials Co
Page 225 and 226:
Complex voscosity (Pa.s) 1,0E+04 1,
Page 227 and 228:
6.3.5.2 Focused Ion Beam (FIB) and
Page 229 and 230:
a) c) b) d) e) f) PMMA PMMA HDPE HD
Page 231 and 232:
y Harkins theory, PS will always si
Page 233 and 234:
a) b) c) d) e) f) PS Figure 6-6. a)
Page 235 and 236:
a) b) HDPE : black PS : grey PMMA :
Page 237 and 238:
6.4.6 Continuity, Co-continuity, an
Page 239 and 240:
c) V III II I VII I IV VI Figure 6-
Page 241 and 242:
Continuity Scheme (a) Figure 6-10.
Page 243 and 244:
Addition of a low concentration of
Page 245 and 246:
Addition of small amounts of HDPE t
Page 247 and 248:
icontinuous network with the HDPE.
Page 249 and 250:
Three examples are shown in Figure
Page 251 and 252:
(9) Mekhilef, N.; Verhoogt, H. Poly
Page 253 and 254:
structures are formed due to the co
Page 255 and 256:
CONCLUSION AND RECOMMENDATIONS In t
Page 257 and 258:
REFERENCES A. K. Gupta, K. R. S. (1
Page 259 and 260:
Caruso, F. (2003). Hollow Inorganic
Page 261 and 262:
Domenech, S. C., Bortoluzzi, J. H.,
Page 263 and 264:
Geuskens, G., Gielens, J. L., Geshe
Page 265 and 266:
Hou, S., Harrell, C. C., Trofin, L.
Page 267 and 268:
Krass, H., Papastavrou, G., & Kurth
Page 269 and 270:
Macdiarmid, A. G., Jin-Chih, C., Ha
Page 271 and 272:
Niziol, J., & Laska, J. (1999). Con
Page 273 and 274:
Reghu, M., Yoon, C. O., Yang, C. Y.
Page 275 and 276:
Shirakawa, H., Louis, E. L., MacDia
Page 277 and 278:
Utracki, L. A. (1991). On the visco
Page 279 and 280:
Yasuda, K., Armstrong, R., & Cohen,
Page 281 and 282:
literature has examined factors inf
Page 283 and 284:
(Reignier & Favis, 2000, 2003a; Rei
Page 285 and 286:
Table A-1.2. Interfacial tensions a
Page 287 and 288:
acquisition of images with a very h
Page 289 and 290:
Table A-1.3. Continuity of the PMMA
Page 291 and 292:
(17) Reignier, J.; Favis, B. D., Ma
Page 293 and 294:
PANI. Theoretically, the extent of
Page 295 and 296:
Equation A-2.7 0( ) 0 1. 5 σ = σ
Page 297 and 298:
Cumulative Mass × 10 5 (g) dipping
Page 299 and 300:
of PANI, and an increase in the con
Page 301 and 302:
Resistance(ohm) 1.0E+12 1.0E+11 1.0
Page 303 and 304:
esistance value. Samples containing
Page 305 and 306:
The results of resistance for PS/PE
Page 307 and 308:
Caruso, F., & Schuler, C. (2000). E
show all

a) b - École Polytechnique de Montréal

Create successful ePaper yourself

Delete template?

Save as template?