Stand-Alone Punch machine user manual - Finn-Power International ...

More documents

Recommendations

Info

From this dialog, the user is able to set the scripting parameters for the part that will be created when the order is ran. 10.3 Exercise- Using Orders Database The following section will describe how to utilize the Orders Database (OMS) feature. Orders Database can be used to increase productivity level when nesting parts. The following steps will show how to add parts manually within the Order Database, nest the parts, and then accept (complete) the order. Once the order is completed a text file will be exported to display parts that have been processed. NOTE- You can tell NC Express what nest run number to start from within the Options menu, under Run Name. Enter the run number one digit before the value you would like to have. For, example you want 1023 you will enter 1022 to achieve this. Step 1: Open Orders Database by going to Database menu | select Orders. Step 2: Select the machine that will be used from the Machine drop down menu. Step 3: Before adding order make sure the Active tab is selected. Step 4: Click Add on dialog to open New Order dialog. Step 5: Enter part order information for three parts listed below (for unidentified fields below leave the fields untouched in the New Order dialog): AutotoolSA.cp Order name: TEST Machine Tool: ‘use current machine’, select from drop down menu. Part name: Click Select to open default part directory. Select AutotoolSA.cp from previous exercises. Priority: 6 Ordered Quantity: 20 Extra parts allowed: 50 Click OK 10-126
NESTPART1.cp Order name: TEST Machine Tool: ‘use current machine’, select from drop down menu. Part name: Select NESTPART1.cp by clicking Select and finding within the default part directory. Priority: 5 Ordered Quantity: 27 Extra parts allowed: 0 Click OK NESTPART2.cp Order name: TEST Machine Tool: ‘use current machine’, select from drop down menu. Part name: Select NESTPART2.cp by clicking Select and finding within the default part directory. Priority: 5 Ordered Quantity: 8 Extra parts allowed: 0 Click OK Step 6: After parts have been entered into the Orders Database they are now ready to be nested. Sort parts by machine name by clicking Machine in Sort by. Select all parts to be nested (parts input from step above) by clicking on the machine name within the grid (white area). Once parts are selected click Nesting [x]… Step 7: Once the parts are nested from the Orders Database the system will start nesting from the run name that you entered within the Options menu. If the run number has already been used the system will ask if it is okay to overwrite the existing folder, click OK to overwrite or Cancel to continue to next number. Note- run folders created before NC Express was currently opened will be asked if it is okay to overwrite, and run folders created while NC Express is currently opened will automatically be skipped. Once the run folder(s) is created the nest dialog will appear. The dialog is set the same way as normal nesting. Set the settings to nest parts as normal. All parts will be scheduled. Modify the sheet size and click OK. Step 8: Once parts have been nested they will need to be optimized and post processed. The nested sheets can either be batch processed or optimized and post processed one by one. Before optimizing go to Process menu | Retool nest and select Automatic. Enable Double hit removal and Punch Common line to remove undesired extra hits within the nest. 10-127
Page 1 and 2:
Finn-Power International 710 Reming
Page 3 and 4:
1 INTRODUCTION ____________________
Page 5 and 6:
4.6.1.3 DESTRUCT __________________
Page 7 and 8:
9.1 USE SPLIT-SCREEN PART DIALOG __
Page 9 and 10:
2 SETTING UP NC EXPRESS The initial
Page 11 and 12:
2.1.1.1.2 Calculation for Stroke Le
Page 13 and 14:
o Optimization group- REGULAR o Con
Page 15 and 16:
NOTE- If the tool’s center point
Page 17 and 18:
Go to Settings menu | Machine Param
Page 19 and 20:
2.2.1 Turret(s) within NC Express T
Page 21 and 22:
2.2.2.1 Station Type Station type w
Page 23 and 24:
e used to allow the B tool to be pl
Page 25 and 26:
3 STARTING TO USE NC EXPRESS Starti
Page 27 and 28:
eing Autotool settings, Nest settin
Page 29 and 30:
Once a new part has been selected a
Page 31 and 32:
To save part either go to File menu
Page 33 and 34:
The duplicate lines were ignored he
Page 35 and 36:
4.3 CP File (Part File) In NC Expre
Page 37 and 38:
Note: Allows you to type in informa
Page 39 and 40:
Step 3: Navigate to a different fol
Page 41 and 42:
Load Parts- In the case where the P
Page 43 and 44:
4.4 Automatic Tooling (Autotool) Th
Page 45 and 46:
4.4.2.4 Settings Tab Settings tab h
Page 47 and 48:
4.4.5 Presheared Parts (Sized parts
Page 49 and 50:
Step 5: Click OK when done modifyin
Page 51 and 52:
Step 5: Click OK to run Autotool. N
Page 53 and 54:
Step 4: Click Apply then OK. Step 5
Page 55 and 56:
Example 2 Below shows example of ro
Page 57 and 58:
Description- important to name taug
Page 59 and 60:
Go to Tooling menu | select Teach C
Page 61 and 62:
‘Show the whole tool library’.
Page 63 and 64:
a. Click outside contour top edge a
Page 65 and 66:
4. Click Undo, on Nibble dialog, to
Page 67 and 68:
3. Add tooling to corner notch a. F
Page 69 and 70:
Clicking will automatically fill i
Page 71 and 72:
The order of tools was changed to m
Page 73 and 74:
Rejoin the cycle Step 4: Left click
Page 75 and 76: Sheet detection- Enable/Disable she
Page 77 and 78: 4.6.5.2 Sorting Sorting is used to
Page 79 and 80: Database for stored plate informati
Page 81 and 82: tools will have restrictions depend
Page 83 and 84: 5.2.3 Template Turret Template turr
Page 85 and 86: to create only one nest pattern. A
Page 87 and 88: Step 2: Setup of part. Open Autotoo
Page 89 and 90: When parameters are set click OK to
Page 91 and 92: c. Open the Nest dialog d. Change t
Page 93 and 94: In general, when utilizing Common L
Page 95 and 96: 5.9 Modifying Part’s/Tooling (for
Page 97 and 98: 6 OPTIMIZATION Optimization is the
Page 99 and 100: When setting the order of the Tool
Page 101 and 102: Punch Optimizer and can be utilized
Page 103 and 104: Once the Punching was changed to St
Page 105 and 106: Interactive Optimizer- Go to Proces
Page 107 and 108: The final outcome of the nest separ
Page 109 and 110: 6.4 Retool Nest (Automatic) Within
Page 111 and 112: Modify automatically optimized plat
Page 113 and 114: 7 Simulator To review an optimized
Page 115 and 116: 8 POST PROCESSING (Create NC Code)
Page 117 and 118: 9 Options and Reports Options, with
Page 119 and 120: Run Name- Enter a nest number only
Page 121 and 122: 9.2.3.3 Printing the Report This ca
Page 123 and 124: o Order: Sort part orders by Order
Page 125: o Nested: All the parts are nested.
Page 129 and 130: 11 Appendix A- Modify tooling Tool
Page 131 and 132: TYPE PARAMETERS DESCRIPTION BOTTOM_
Page 133 and 134: Tapping Starting Value Starting lev
Page 135 and 136: 12 Appendix B- Special tool informa
Page 137 and 138: • Protection length (C)- Sets len
Page 139 and 140: 26 0.0179 0.001 0.002 0.003 24 0.02
Page 141 and 142: Destruct tab o Sorting device- allo
Page 143 and 144: Settings tab Use this tab to set de
Page 145 and 146: Zone Number (Zone) Tool packages (
Page 147 and 148: 16 Appendix F- Interactive Zones Se
show all

Stand-Alone Punch machine user manual - Finn-Power International ...

Create successful ePaper yourself

Delete template?

Save as template?