Stand-Alone Punch machine user manual - Finn-Power International ...

More documents

Recommendations

Info

14 Appendix D- Autotool Settings General tab Machining mode- select the type of tooling to be placed on part. For turret punch press machines only punch and nibble can be selected. o Punch and Nibble- Allows tooling to be used throughout part. o Laser- used to tool a part with shear tooling. o Preshear- tools only interior geometry. Cut bottom strip- tools entire bottom geometry of part to be used for skeleton free cutting in nesting. o Use taught cycles- enables the use of taught cycles that have been created. Alternative tooling- Allows user to tool part with variational tooling (tooling a part with 1 or more rotations). o Use only 1 tooling- only tools part at 0° orientation. Part can then be nested only at 0° rotation. o Use 0° & 90° tooling- tool parts only for 0° & 90° rotation for nesting. o Use 0° & 180° tooling- tool parts only for 0° & 180° rotation for nesting. o Create 4 tooling orientations- tool parts in all orientations (0°, 90°, 180°, and 270°). o Tool this orientation only- tool only selected orientation with Autotool again. CAD Layer Filter- used to filter layers of dxf files and DADO lines and points. o Closed Contours- closed geometry used by system for offset cutting. This variable can be alphanumeric or “ALL”. Layers from imported dxf file that are desired layers to be tooled are entered exactly as NC Express sees them. (Layers defined can be viewed by going to Settings menu | CAD then select layers…) o DADOS- open geometry used by system for centerline cutting. Cannot be “ALL”. Enter DADO for DADO lines to be tooled. Tool library- o Use only current turret- Select which turret part will be tooled from if there are multiple turrets setup in NC Express. (Note- only uses tooling turret not tapping turret.) o Use main tool library- allows the use of the current tool library. Uses entire tool library, per die clearance range of material thickness range. Utilizing ‘Use main tool library’ will allow tools to automatically be loaded into the turret by the optimizer, if not loaded in turret already. Unloading- Enables sorting devices in machine. 14-140
Destruct tab o Sorting device- allows user to change sorting automatically for specific part. Sorting devices are setup in the machine parameters. o No sorting (microjointed)- sets external microjoints on part. Punch Destruct Consumes the entire material within the given variables. Max. Rectangular hole- enter the maximum area to be destructed. Max. Round Hole- enter the diameter to be destructed. Note- For destructing squares/rectangles and holes the number being inputted into the settings must be larger than the size of the square/rectangle or hole. (Ex. Take a square cutout that is 30mm x 40mm. If you wanted to destruct all material within take the longest line for the cutout, which is 40mm. A value larger) If the number is smaller the contour will be nibbled and not destructed. Any Contour Type Enabled- applies destruction to more complex internal contour when activated. External Contour Notch Destruct Destructs outside notches of a part. For LP combo only used when punch only is used for parts. Outside Expansion- extends tool the given value past the opening of the notch. Any Notch Type Enabled- applies destruction to more complex notches when activated. Uses value ‘Allowed outside shape extension’ from ‘Settings’ tab for tooling expansion outside of part edge instead of Outside Expansion from the ‘Destruct’ tab. 14-141
Page 1 and 2:
Finn-Power International 710 Reming
Page 3 and 4:
1 INTRODUCTION ____________________
Page 5 and 6:
4.6.1.3 DESTRUCT __________________
Page 7 and 8:
9.1 USE SPLIT-SCREEN PART DIALOG __
Page 9 and 10:
2 SETTING UP NC EXPRESS The initial
Page 11 and 12:
2.1.1.1.2 Calculation for Stroke Le
Page 13 and 14:
o Optimization group- REGULAR o Con
Page 15 and 16:
NOTE- If the tool’s center point
Page 17 and 18:
Go to Settings menu | Machine Param
Page 19 and 20:
2.2.1 Turret(s) within NC Express T
Page 21 and 22:
2.2.2.1 Station Type Station type w
Page 23 and 24:
e used to allow the B tool to be pl
Page 25 and 26:
3 STARTING TO USE NC EXPRESS Starti
Page 27 and 28:
eing Autotool settings, Nest settin
Page 29 and 30:
Once a new part has been selected a
Page 31 and 32:
To save part either go to File menu
Page 33 and 34:
The duplicate lines were ignored he
Page 35 and 36:
4.3 CP File (Part File) In NC Expre
Page 37 and 38:
Note: Allows you to type in informa
Page 39 and 40:
Step 3: Navigate to a different fol
Page 41 and 42:
Load Parts- In the case where the P
Page 43 and 44:
4.4 Automatic Tooling (Autotool) Th
Page 45 and 46:
4.4.2.4 Settings Tab Settings tab h
Page 47 and 48:
4.4.5 Presheared Parts (Sized parts
Page 49 and 50:
Step 5: Click OK when done modifyin
Page 51 and 52:
Step 5: Click OK to run Autotool. N
Page 53 and 54:
Step 4: Click Apply then OK. Step 5
Page 55 and 56:
Example 2 Below shows example of ro
Page 57 and 58:
Description- important to name taug
Page 59 and 60:
Go to Tooling menu | select Teach C
Page 61 and 62:
‘Show the whole tool library’.
Page 63 and 64:
a. Click outside contour top edge a
Page 65 and 66:
4. Click Undo, on Nibble dialog, to
Page 67 and 68:
3. Add tooling to corner notch a. F
Page 69 and 70:
Clicking will automatically fill i
Page 71 and 72:
The order of tools was changed to m
Page 73 and 74:
Rejoin the cycle Step 4: Left click
Page 75 and 76:
Sheet detection- Enable/Disable she
Page 77 and 78:
4.6.5.2 Sorting Sorting is used to
Page 79 and 80:
Database for stored plate informati
Page 81 and 82:
tools will have restrictions depend
Page 83 and 84:
5.2.3 Template Turret Template turr
Page 85 and 86:
to create only one nest pattern. A
Page 87 and 88:
Step 2: Setup of part. Open Autotoo
Page 89 and 90: When parameters are set click OK to
Page 91 and 92: c. Open the Nest dialog d. Change t
Page 93 and 94: In general, when utilizing Common L
Page 95 and 96: 5.9 Modifying Part’s/Tooling (for
Page 97 and 98: 6 OPTIMIZATION Optimization is the
Page 99 and 100: When setting the order of the Tool
Page 101 and 102: Punch Optimizer and can be utilized
Page 103 and 104: Once the Punching was changed to St
Page 105 and 106: Interactive Optimizer- Go to Proces
Page 107 and 108: The final outcome of the nest separ
Page 109 and 110: 6.4 Retool Nest (Automatic) Within
Page 111 and 112: Modify automatically optimized plat
Page 113 and 114: 7 Simulator To review an optimized
Page 115 and 116: 8 POST PROCESSING (Create NC Code)
Page 117 and 118: 9 Options and Reports Options, with
Page 119 and 120: Run Name- Enter a nest number only
Page 121 and 122: 9.2.3.3 Printing the Report This ca
Page 123 and 124: o Order: Sort part orders by Order
Page 125 and 126: o Nested: All the parts are nested.
Page 127 and 128: NESTPART1.cp Order name: TEST Mac
Page 129 and 130: 11 Appendix A- Modify tooling Tool
Page 131 and 132: TYPE PARAMETERS DESCRIPTION BOTTOM_
Page 133 and 134: Tapping Starting Value Starting lev
Page 135 and 136: 12 Appendix B- Special tool informa
Page 137 and 138: • Protection length (C)- Sets len
Page 139: 26 0.0179 0.001 0.002 0.003 24 0.02
Page 143 and 144: Settings tab Use this tab to set de
Page 145 and 146: Zone Number (Zone) Tool packages (
Page 147 and 148: 16 Appendix F- Interactive Zones Se
show all

Stand-Alone Punch machine user manual - Finn-Power International ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?