Stand-Alone Punch machine user manual - Finn-Power International ...

More documents

Recommendations

Info

4.5 Teach Cycles This feature allows a user to store tooled geometrical shapes so that Autotool remembers them and applies the same tooling again when it sees the same geometry. Tooling and geometry are selected together to apply this feature. When running Autotool with teach cycles selected it will look for the same geometrical shapes that have a cycle taught and apply the tooling at any rotation (any rotation if the taught cycle has the rotation turned on). Teach cycles also has the ability to create cycles (pattern) when applying tooling to a part. When a part has many tool hits you may teach the first hit then repeat this in direction of your choice to create a cycle (pattern). Also, manual cycles can also be set before applying teach cycles. Example, a part requires a punch-form-tap for 3mm holes within a part. Part will have all three tools applied to the hole. If desired the operation can be manual cycled with sync settings, meaning that the order would occur with tool changes. Apply teach cycle to the tooling and geometry. Autotool part and each 3mm hole within the part will have this same tooling applied. Example 1 Below shows the use of pattern and rotation: Pattern dictates outcome of cycle. Selecting X+, then Y+ will allow cycle to start moving positive in the X axis then one level up in the Y axis then again move positive in the X axis. Selecting Y+, then X+ will do just the opposite. Cycle will be created positive in the Y-axis then move one row positive in the X-axis then continue positive in the Y-axis. Pictured below is an example of a teach cycle created with pattern First X+, then Y-. 4-54
Example 2 Below shows example of rotation of teach cycles Creating a teach cycle with rotation can be a nice time saver. This allows you to create a teach cycle for tooling in a corner which may be very difficult to tool manually, this may be repeated for each corner of the part every time Autotool is ran with teach cycles turned on. Free rotation- Allows teach cycle to be rotated freely. (Note- when tooling corner with non-indexable tool and free rotation is turned on tool’s characteristics will be overridden in teach cycles allowing tool to rotate.) Rectangle symmetry- Can be rotated 180° and mirrored around Y-axis. Square symmetry- Can be rotated 90°, 180°, and 270° and mirrored around Yaxis. Don’t rotate- Allows taught cycle to be used only in original design. 4-55
Page 1 and 2:
Finn-Power International 710 Reming
Page 3 and 4: 1 INTRODUCTION ____________________
Page 5 and 6: 4.6.1.3 DESTRUCT __________________
Page 7 and 8: 9.1 USE SPLIT-SCREEN PART DIALOG __
Page 9 and 10: 2 SETTING UP NC EXPRESS The initial
Page 11 and 12: 2.1.1.1.2 Calculation for Stroke Le
Page 13 and 14: o Optimization group- REGULAR o Con
Page 15 and 16: NOTE- If the tool’s center point
Page 17 and 18: Go to Settings menu | Machine Param
Page 19 and 20: 2.2.1 Turret(s) within NC Express T
Page 21 and 22: 2.2.2.1 Station Type Station type w
Page 23 and 24: e used to allow the B tool to be pl
Page 25 and 26: 3 STARTING TO USE NC EXPRESS Starti
Page 27 and 28: eing Autotool settings, Nest settin
Page 29 and 30: Once a new part has been selected a
Page 31 and 32: To save part either go to File menu
Page 33 and 34: The duplicate lines were ignored he
Page 35 and 36: 4.3 CP File (Part File) In NC Expre
Page 37 and 38: Note: Allows you to type in informa
Page 39 and 40: Step 3: Navigate to a different fol
Page 41 and 42: Load Parts- In the case where the P
Page 43 and 44: 4.4 Automatic Tooling (Autotool) Th
Page 45 and 46: 4.4.2.4 Settings Tab Settings tab h
Page 47 and 48: 4.4.5 Presheared Parts (Sized parts
Page 49 and 50: Step 5: Click OK when done modifyin
Page 51 and 52: Step 5: Click OK to run Autotool. N
Page 53: Step 4: Click Apply then OK. Step 5
Page 57 and 58: Description- important to name taug
Page 59 and 60: Go to Tooling menu | select Teach C
Page 61 and 62: ‘Show the whole tool library’.
Page 63 and 64: a. Click outside contour top edge a
Page 65 and 66: 4. Click Undo, on Nibble dialog, to
Page 67 and 68: 3. Add tooling to corner notch a. F
Page 69 and 70: Clicking will automatically fill i
Page 71 and 72: The order of tools was changed to m
Page 73 and 74: Rejoin the cycle Step 4: Left click
Page 75 and 76: Sheet detection- Enable/Disable she
Page 77 and 78: 4.6.5.2 Sorting Sorting is used to
Page 79 and 80: Database for stored plate informati
Page 81 and 82: tools will have restrictions depend
Page 83 and 84: 5.2.3 Template Turret Template turr
Page 85 and 86: to create only one nest pattern. A
Page 87 and 88: Step 2: Setup of part. Open Autotoo
Page 89 and 90: When parameters are set click OK to
Page 91 and 92: c. Open the Nest dialog d. Change t
Page 93 and 94: In general, when utilizing Common L
Page 95 and 96: 5.9 Modifying Part’s/Tooling (for
Page 97 and 98: 6 OPTIMIZATION Optimization is the
Page 99 and 100: When setting the order of the Tool
Page 101 and 102: Punch Optimizer and can be utilized
Page 103 and 104: Once the Punching was changed to St
Page 105 and 106:
Interactive Optimizer- Go to Proces
Page 107 and 108:
The final outcome of the nest separ
Page 109 and 110:
6.4 Retool Nest (Automatic) Within
Page 111 and 112:
Modify automatically optimized plat
Page 113 and 114:
7 Simulator To review an optimized
Page 115 and 116:
8 POST PROCESSING (Create NC Code)
Page 117 and 118:
9 Options and Reports Options, with
Page 119 and 120:
Run Name- Enter a nest number only
Page 121 and 122:
9.2.3.3 Printing the Report This ca
Page 123 and 124:
o Order: Sort part orders by Order
Page 125 and 126:
o Nested: All the parts are nested.
Page 127 and 128:
NESTPART1.cp Order name: TEST Mac
Page 129 and 130:
11 Appendix A- Modify tooling Tool
Page 131 and 132:
TYPE PARAMETERS DESCRIPTION BOTTOM_
Page 133 and 134:
Tapping Starting Value Starting lev
Page 135 and 136:
12 Appendix B- Special tool informa
Page 137 and 138:
• Protection length (C)- Sets len
Page 139 and 140:
26 0.0179 0.001 0.002 0.003 24 0.02
Page 141 and 142:
Destruct tab o Sorting device- allo
Page 143 and 144:
Settings tab Use this tab to set de
Page 145 and 146:
Zone Number (Zone) Tool packages (
Page 147 and 148:
16 Appendix F- Interactive Zones Se
show all

Stand-Alone Punch machine user manual - Finn-Power International ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?