Stand-Alone Punch machine user manual - Finn-Power International ...

More documents

Recommendations

Info

the desired tool to be used on the start and end points. Extensions can be modified to change the overlap outside the edge of the vertex of the tool that is used to nibble. Delete rectangle tooling within part: Replace- (Edit menu | Replace) Select each of the rectangle tools in the ‘Find tool ID’ drop down, then click Remove. Both rectangle tools will be removed separately. 1. Click Setting Nibble Priorities in the Nibble dialog. 2. Modify Extension 1 & Extension 2: -0.006” (-0.15mm) 3. Click on each of the outside contour line segments to add rectangle tooling. (Also tool the inside cutout) Part should look similar to picture below. Nibbling Radius Contours When adding a round tool nibble path to a radius contour the most important Nibble Property is the Scallop Maximum. The scallop maximum will adjust the size of the teeth left when nibbling with a round tool. 1. From the Nibble dialog select a round tool- 0.5” (12mm) 2. Click Setting Nibble Properties a. Change Scallop Max: 0.03” (0.8mm) 3. Click on Round cutout on right side of the part to add nibble path. (Go to View menu | Display – select Expand Nibbles, to view single hits made. Zoom in to get a better view of hole.) 4-64
4. Click Undo, on Nibble dialog, to remove tooling that was just placed. 5. Change Scallop Max: 0.008” (0.2mm) 6. Click Round cutout to add tooling. The punches added will increase as well as decreasing the size of the “teeth” left after punching. A smaller Scallop Maximum value will add more punches to a radius nibble path. 4.6.1.3 DESTRUCT Destruct applies tooling to destruct material either in a notch or internal contour. Only square or round (special tool Multi-radius) tools can be used in conjunction with Destruct. The following will demonstrate how to destruct notches as well as internal cutouts (round and square) using Interactive Tooling Destruct. 1. Select (Destruct) from the toolbar. 2. Click Parameter>> to set property values: a. Set Scallop: 0.007” (0.1mm) b. Set Overlap: 0.04” (1mm) c. Set Notch expansion: 0” (0mm) Destructing Notches 4-65
Page 1 and 2:
Finn-Power International 710 Reming
Page 3 and 4:
1 INTRODUCTION ____________________
Page 5 and 6:
4.6.1.3 DESTRUCT __________________
Page 7 and 8:
9.1 USE SPLIT-SCREEN PART DIALOG __
Page 9 and 10:
2 SETTING UP NC EXPRESS The initial
Page 11 and 12:
2.1.1.1.2 Calculation for Stroke Le
Page 13 and 14: o Optimization group- REGULAR o Con
Page 15 and 16: NOTE- If the tool’s center point
Page 17 and 18: Go to Settings menu | Machine Param
Page 19 and 20: 2.2.1 Turret(s) within NC Express T
Page 21 and 22: 2.2.2.1 Station Type Station type w
Page 23 and 24: e used to allow the B tool to be pl
Page 25 and 26: 3 STARTING TO USE NC EXPRESS Starti
Page 27 and 28: eing Autotool settings, Nest settin
Page 29 and 30: Once a new part has been selected a
Page 31 and 32: To save part either go to File menu
Page 33 and 34: The duplicate lines were ignored he
Page 35 and 36: 4.3 CP File (Part File) In NC Expre
Page 37 and 38: Note: Allows you to type in informa
Page 39 and 40: Step 3: Navigate to a different fol
Page 41 and 42: Load Parts- In the case where the P
Page 43 and 44: 4.4 Automatic Tooling (Autotool) Th
Page 45 and 46: 4.4.2.4 Settings Tab Settings tab h
Page 47 and 48: 4.4.5 Presheared Parts (Sized parts
Page 49 and 50: Step 5: Click OK when done modifyin
Page 51 and 52: Step 5: Click OK to run Autotool. N
Page 53 and 54: Step 4: Click Apply then OK. Step 5
Page 55 and 56: Example 2 Below shows example of ro
Page 57 and 58: Description- important to name taug
Page 59 and 60: Go to Tooling menu | select Teach C
Page 61 and 62: ‘Show the whole tool library’.
Page 63: a. Click outside contour top edge a
Page 67 and 68: 3. Add tooling to corner notch a. F
Page 69 and 70: Clicking will automatically fill i
Page 71 and 72: The order of tools was changed to m
Page 73 and 74: Rejoin the cycle Step 4: Left click
Page 75 and 76: Sheet detection- Enable/Disable she
Page 77 and 78: 4.6.5.2 Sorting Sorting is used to
Page 79 and 80: Database for stored plate informati
Page 81 and 82: tools will have restrictions depend
Page 83 and 84: 5.2.3 Template Turret Template turr
Page 85 and 86: to create only one nest pattern. A
Page 87 and 88: Step 2: Setup of part. Open Autotoo
Page 89 and 90: When parameters are set click OK to
Page 91 and 92: c. Open the Nest dialog d. Change t
Page 93 and 94: In general, when utilizing Common L
Page 95 and 96: 5.9 Modifying Part’s/Tooling (for
Page 97 and 98: 6 OPTIMIZATION Optimization is the
Page 99 and 100: When setting the order of the Tool
Page 101 and 102: Punch Optimizer and can be utilized
Page 103 and 104: Once the Punching was changed to St
Page 105 and 106: Interactive Optimizer- Go to Proces
Page 107 and 108: The final outcome of the nest separ
Page 109 and 110: 6.4 Retool Nest (Automatic) Within
Page 111 and 112: Modify automatically optimized plat
Page 113 and 114: 7 Simulator To review an optimized
Page 115 and 116:
8 POST PROCESSING (Create NC Code)
Page 117 and 118:
9 Options and Reports Options, with
Page 119 and 120:
Run Name- Enter a nest number only
Page 121 and 122:
9.2.3.3 Printing the Report This ca
Page 123 and 124:
o Order: Sort part orders by Order
Page 125 and 126:
o Nested: All the parts are nested.
Page 127 and 128:
NESTPART1.cp Order name: TEST Mac
Page 129 and 130:
11 Appendix A- Modify tooling Tool
Page 131 and 132:
TYPE PARAMETERS DESCRIPTION BOTTOM_
Page 133 and 134:
Tapping Starting Value Starting lev
Page 135 and 136:
12 Appendix B- Special tool informa
Page 137 and 138:
• Protection length (C)- Sets len
Page 139 and 140:
26 0.0179 0.001 0.002 0.003 24 0.02
Page 141 and 142:
Destruct tab o Sorting device- allo
Page 143 and 144:
Settings tab Use this tab to set de
Page 145 and 146:
Zone Number (Zone) Tool packages (
Page 147 and 148:
16 Appendix F- Interactive Zones Se
show all

Stand-Alone Punch machine user manual - Finn-Power International ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?