ER-A440 Operation-Manual GB - Sharp

More documents

Recommendations

Info

8 Programming the tax rate Tax rate PGM 2 Procedure *A ◊ 1-6 To program zero ≈ **Sign and tax rate ≈ Lowest taxable amount ; max. five digits: 0.00 to 999.99 * A: Enter a corresponding tax rate number. For example, when you program a tax rate as tax rate 1, enter “1”, and when you program it as tax rate 6, enter “6”. ** Sign and tax rate: XYYY.YYYY Tax rate= 0.0001 to 100.0000 Sign - /+ = 1 /0 Note • The lowest taxable amount is valid only when you select add on tax system. If you select VAT (Value added tax) system, it is ignored. • If you make an incorrect entry before pressing the second ≈ key in programming a tax rate, cancel it with the c key; and if you make an error after pressing the second ≈ key, cancel it with the : key. Then program again from the beginning. • If you select VAT system, the sign which you program is ignored. Example Programming the tax rate (+4%) as tax rate 2 with lowest taxable income as 0.12. 1. Press the ◊ key. ◊ 2. Enter the tax rate “2”. 2 ≈ 3. Enter the tax rate “+4%.” 4 ≈ 4. Enter the lowest taxable amount “12.” 12 5. Press the ; key to finalize the programming ; and generate a programming report. Print P 0.00 P 0.00 P 0.00 P 12 0.00 Tax rate 2 Tax rate : 4% Lowest taxable amount 26
Job-Code-Based Programming This section illustrates how to program items using job codes. Using job codes allows you to program a wide variety of items in comparison with direct programming. Start this programming by entering a corresponding job code as shown below. 2110 . ≈ All the items which can be programmed by the job-code-based programming are listed on this page and the following, and those which can also be programmed by the direct programming are marked with the symbol “ Direct ” that follows job codes. Note When setting the parameters for a job code, the digit that is blinking is the one that can be changed. To go to the position of the parameter that you want to change, press either of the following keys : . Moves the blinker to the right. º Moves the blinker to the left. 1 Setting the date and time Setting the date Enter day (one or two digits), month (two digits), and year (two digits) in this sequence. Procedure PGM 2 2610 Direct 2610 Date (five or six digits) . ≈ ; Example Key operation 2610 . ≈ 260898 ; Print Date Setting the time Set the time using the 24-hour format. For example, when the time is set to 2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430. Procedure PGM 2 2611 Direct 2611 Time (max. four digits) . ≈ ; 27
Page 1 and 2: ELECTRONIC CASH REGISTER INSTRUCTIO
Page 3 and 4: INTRODUCTION Thank you very much fo
Page 5 and 6: Job-Code-Based Programming ····
Page 7 and 8: Difference subtotal (Differ ST) ·
Page 9 and 10: PRINTER INSTALLING AND REMOVING THE
Page 11 and 12: EX1 EX2 Foreign currency exchange 1
Page 13 and 14: DISPLAYS Operator display Customer
Page 15 and 16: • Numerals, letters and symbols a
Page 17 and 18: PROGRAMMING Your machine allows you
Page 19 and 20: Print Dept. code Unit price Functio
Page 21 and 22: 3 Price lookup (PLU) programming A
Page 23 and 24: Example Programming for PLU code 1
Page 25 and 26: High amount lockout (HALO) and +/-
Page 27: 6 Programming for exchange keys Cur
Page 31 and 32: Example Key operation 2613 . ≈ 10
Page 33 and 34: Example Key operation Print 2110 .
Page 35 and 36: Alphanumeric characters PGM 2 2114
Page 37 and 38: Example Key operation2 : ; Print 21
Page 39 and 40: Note For some items, you can progra
Page 41 and 42: PLU/subdepartment mode PGM 2 2210 2
Page 43 and 44: Example For each PLU Key operation
Page 45 and 46: Link PLU Procedure PGM 2 2220 Cance
Page 47 and 48: A limit amount (HALO) of entry (-,
Page 49 and 50: Item % or subtotal % selection (%)
Page 51 and 52: 7 Programming for the ;, Å, ( thro
Page 55 and 56: Function no. Key or function Defaul
Page 57 and 58: Clerk code You can assign a clerk c
Page 59 and 60: **P: 1 * Item: Selection: Entry: A
Page 63 and 64: Selection of X1/Z1 and X2/Z2 report
Page 65 and 66: Secret codes to control access to P
Page 67 and 68: . . . . . . . . . . Setting the AUT
Page 69 and 70: Sample printouts 1 Reading of progr
Page 71: 7 Reading of programmed items for f
Page 74 and 75: 12 Training mode The training mode
Page 76 and 77: Item Commission sales report Readin
Page 78 and 79:
3 Daily sales totals Full reading a
Page 80 and 81:
Validation print counter No-sale (e
Page 82 and 83:
Clerk reading and resetting Using t
Page 84 and 85:
Full department reading Sales q'ty
Page 86 and 87:
Reading and resetting of sales info
Page 88 and 89:
Transaction reading Total in drawer
Page 90 and 91:
Reading and resetting of the daily
Page 92 and 93:
CCD entry amount Currency exchange
Page 94 and 95:
CORRECTION AFTER FINALIZING A TRANS
Page 96 and 97:
Procedure Cashier assignment ■ Si
Page 98 and 99:
Repeat entries You can use this fun
Page 100 and 101:
Split-pricing entries You will use
Page 102 and 103:
Printing leading link PLUs and tota
Page 104 and 105:
Credit sale Enter items and press t
Page 106 and 107:
VAT shift entries This feature is i
Page 108 and 109:
Refund entries If a refund item is
Page 110 and 111:
Example Key operation Print 6789 =
Page 112 and 113:
3 Subtotal void You can void an ent
Page 114 and 115:
2 Guest check copy You can use this
Page 116 and 117:
• Void entry Validation printing
Page 118 and 119:
OVERLAPPED CASHIER ENTRY This funct
Page 120 and 121:
4 Installing and removing the paper
Page 122 and 123:
3. Press and hold the journal paper
Page 124 and 125:
6 Removing the till and the drawer
Page 126 and 127:
9 The malfunctions shown in the lef
Page 128 and 129:
SPECIFICATIONS Model: ER-A440 Dimen
Page 130:
SHARP CORPORATION Printed in Korea
show all

ER-A440 Operation-Manual GB - Sharp

Create successful ePaper yourself

Delete template?

Save as template?