ER-A440 Operation-Manual GB - Sharp

More documents

Recommendations

Info

Setting the time range for hourly reports You can set the time range for an hourly report. Procedure PGM 2 2619 When A through C are all zeros * 2619 ABC . ≈ ; *A: Time range To set the time range to 30 minutes (in the 24-hour system), enter 0. To set the time range to 60 minutes (in the 24-hour system), enter 1. BC: Starting time (hour = 00 to 23) Example Key operation 2619 . ≈ 107 ; Print Note To perform this setting, an hourly Z report (# 160) must be done. RS-232C channel assignment Your machine is equipped with an RS-232C interface. If you use the on-line communication function, the channel number of the RS-232C interface must be programmed by using the following procedure. To realize the on-line communication, consult your dealer. Procedure When A through D are all zeroes 2690 *P **ABCD . ≈ ≈ : ; 1 to 3 PGM 2 *P: 1 ** Item: Selection: Entry: A For the ON-LINE communication Disable 0 Enable (enter the channel number) 8 B to D Always enter 0. 0 *P: 2 and 3 (ABCD: Not used. Always enter 0.) 2690 Example Key operation 2690 . ≈ 1 ≈ : ; Print P A through D 62
Secret codes to control access to PGM1 mode, X1/Z1 mode and X2/Z2 mode PGM 2 2630 2631 2632 You must enter a secret code according to the following procedure before performing any PGM1-mode, X1/Z1- mode or X2/Z2-mode operation when a secret code has been set for that specific mode operation. Operating Procedure ; Secret code ; Max. 4 digits Note Programming Procedure Once a secret code is entered, it does not need to be entered again unless the mode switch setting is changed and any operation, such as a sales registration, reporting, or programming, is performed. * 2630 2631 * 2630 for the PGM1 mode 2631 for the X1/Z1 mode 2632 for the X2/Z2 mode Example No code (zero) Secret code . ≈ ; 2632 Max. 4 digits Key operation 2631 . ≈ 1234 ; Print Currency description text programming PGM 2 2334 You can program a maximum of 4 characters for each of the [ through ” keys. Procedure To program spaces Character keys 2334 *Function no. . ≈ ≈ (max. 4 digits) : ; *Function no.: 52: For the [ key 53: For the { key 54: For the “ key 55: For the ” key 63
Page 1 and 2:
ELECTRONIC CASH REGISTER INSTRUCTIO
Page 3 and 4:
INTRODUCTION Thank you very much fo
Page 5 and 6:
Job-Code-Based Programming ····
Page 7 and 8:
Difference subtotal (Differ ST) ·
Page 9 and 10:
PRINTER INSTALLING AND REMOVING THE
Page 11 and 12:
EX1 EX2 Foreign currency exchange 1
Page 13 and 14: DISPLAYS Operator display Customer
Page 15 and 16: • Numerals, letters and symbols a
Page 17 and 18: PROGRAMMING Your machine allows you
Page 19 and 20: Print Dept. code Unit price Functio
Page 21 and 22: 3 Price lookup (PLU) programming A
Page 23 and 24: Example Programming for PLU code 1
Page 25 and 26: High amount lockout (HALO) and +/-
Page 27 and 28: 6 Programming for exchange keys Cur
Page 29 and 30: Job-Code-Based Programming This sec
Page 31 and 32: Example Key operation 2613 . ≈ 10
Page 33 and 34: Example Key operation Print 2110 .
Page 35 and 36: Alphanumeric characters PGM 2 2114
Page 37 and 38: Example Key operation2 : ; Print 21
Page 39 and 40: Note For some items, you can progra
Page 41 and 42: PLU/subdepartment mode PGM 2 2210 2
Page 43 and 44: Example For each PLU Key operation
Page 45 and 46: Link PLU Procedure PGM 2 2220 Cance
Page 47 and 48: A limit amount (HALO) of entry (-,
Page 49 and 50: Item % or subtotal % selection (%)
Page 51 and 52: 7 Programming for the ;, Å, ( thro
Page 55 and 56: Function no. Key or function Defaul
Page 57 and 58: Clerk code You can assign a clerk c
Page 59 and 60: **P: 1 * Item: Selection: Entry: A
Page 63: Selection of X1/Z1 and X2/Z2 report
Page 67 and 68: . . . . . . . . . . Setting the AUT
Page 69 and 70: Sample printouts 1 Reading of progr
Page 71: 7 Reading of programmed items for f
Page 74 and 75: 12 Training mode The training mode
Page 76 and 77: Item Commission sales report Readin
Page 78 and 79: 3 Daily sales totals Full reading a
Page 80 and 81: Validation print counter No-sale (e
Page 82 and 83: Clerk reading and resetting Using t
Page 84 and 85: Full department reading Sales q'ty
Page 86 and 87: Reading and resetting of sales info
Page 88 and 89: Transaction reading Total in drawer
Page 90 and 91: Reading and resetting of the daily
Page 92 and 93: CCD entry amount Currency exchange
Page 94 and 95: CORRECTION AFTER FINALIZING A TRANS
Page 96 and 97: Procedure Cashier assignment ■ Si
Page 98 and 99: Repeat entries You can use this fun
Page 100 and 101: Split-pricing entries You will use
Page 102 and 103: Printing leading link PLUs and tota
Page 104 and 105: Credit sale Enter items and press t
Page 106 and 107: VAT shift entries This feature is i
Page 108 and 109: Refund entries If a refund item is
Page 110 and 111: Example Key operation Print 6789 =
Page 112 and 113: 3 Subtotal void You can void an ent
Page 114 and 115:
2 Guest check copy You can use this
Page 116 and 117:
• Void entry Validation printing
Page 118 and 119:
OVERLAPPED CASHIER ENTRY This funct
Page 120 and 121:
4 Installing and removing the paper
Page 122 and 123:
3. Press and hold the journal paper
Page 124 and 125:
6 Removing the till and the drawer
Page 126 and 127:
9 The malfunctions shown in the lef
Page 128 and 129:
SPECIFICATIONS Model: ER-A440 Dimen
Page 130:
SHARP CORPORATION Printed in Korea
show all

ER-A440 Operation-Manual GB - Sharp

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?