Wavelink Avalanche Site Edition Java Console User Guide

More documents

Recommendations

Info

Chapter 8: Managing Scan to Configure Profiles 78 To configure the settings: 1 From the Profiles tab, select the Scan to Config Profile you want to configure. Click Edit. 2 To encrypt the barcodes, type a passcode in the Encryption Passcode text box and confirm it in the Confirm Passcode text box. 3 Set the maximum length of the barcode. 4 If you have already configured a network profile and want to use the settings from that profile, enable Use settings from network profile. Choose which epoch to use by enabling either Use currently active Epoch or Use selected Epoch and selecting an epoch from the drop‐down list. 5 If you want to set a static IP address for the device, enable Assign static IP address and type the IP Address, Subnet Mask and Gateway in the appropriate boxes. NOTE You cannot set a static IP address and use a network profile concurrently. 6 Click Save to save your changes. The profile is updated with the configured network settings. Adding Scan to Config Profile Authorized <strong>User</strong>s You can add authorized users for all scan to config profiles or enable a user for a specific scan to config profile. For information on adding an authorized user, see Chapter 5: Managing <strong>User</strong> Accounts on page 43. Editing Custom Properties Custom properties allow you to define specific properties that you want applied to the mobile device. An example of a custom property would be location = Chicago. Once a custom property has been applied to a device, you can use it as a selection criterion. You can apply custom properties to mobile devices through a Scan to Config Profile.
Chapter 8: Managing Scan to Configure Profiles 79 You also have the option to edit or remove custom properties currently existing on the device through a Scan to Config Profile. You must know the name of the property in order to edit or remove it. This section contains information on the following tasks: • Adding a Custom Property • Editing or Removing a Custom Property Adding a Custom Property You can add a custom property to a mobile device through a Scan to Config Profile. Add the property to the profile, print the profile as a set of barcodes, and scan the barcodes with the device. To add a custom property: 1 From the Profiles tab, select the Scan to Config Profile you want to configure. 2 Click Edit. 3 In the Device Properties region, click Add. The Edit Property dialog box appears. 4 Type the Name and Value in the text boxes. 5 Select whether the property should be a device property or a network property. 6 Click OK. The task is added to the list in the Device Properties region. The property will be added when the barcodes are scanned by the mobile device. 7 Click Save to save your changes. Editing or Removing a Custom Property You can edit or remove an existing custom property on a mobile device through a Scan to Config Profile. Make changes to the property from the profile, print the profile as a set of barcodes, and scan the barcodes with the device. You must know the name of the property in order to edit or remove it.
Page 1 and 2:
Wavelink Avalanche Site Edition Jav
Page 3 and 4:
Table of Contents 1 Table of Conten
Page 5 and 6:
Table of Contents 3 Configuring Sch
Page 7 and 8:
Table of Contents 5 Mobile Device P
Page 9 and 10:
Chapter 1: Introduction 7 Chapter 1
Page 11 and 12:
Chapter 1: Introduction 9 • Locat
Page 13 and 14:
Chapter 1: Introduction 11 Once you
Page 15 and 16:
Chapter 2: Installing Avalanche 13
Page 17 and 18:
Chapter 3: Licensing 15 variety of
Page 19 and 20:
Chapter 3: Licensing 17 Figure 3-1.
Page 21 and 22:
Chapter 3: Licensing 19 To import a
Page 23 and 24:
Chapter 3: Licensing 21 NOTE If you
Page 25 and 26:
Chapter 4: Avalanche Console 23 Cha
Page 27 and 28:
Chapter 4: Avalanche Console 25 •
Page 29 and 30: Chapter 4: Avalanche Console 27 Pro
Page 31 and 32: Chapter 4: Avalanche Console 29 Whi
Page 33 and 34: Chapter 4: Avalanche Console 31 3 I
Page 35 and 36: Chapter 4: Avalanche Console 33 Sch
Page 37 and 38: Chapter 4: Avalanche Console 35 Con
Page 39 and 40: Chapter 4: Avalanche Console 37 Par
Page 41 and 42: Chapter 4: Avalanche Console 39 Fro
Page 43 and 44: Chapter 4: Avalanche Console 41 NOT
Page 45 and 46: Chapter 5: Managing User Accounts 4
Page 57 and 58: Chapter 6: Managing Sites and Locat
Page 65 and 66: Chapter 7: Managing Network Profile
Page 79: Chapter 8: Managing Scan to Configu
Page 83 and 84: Chapter 8: Managing Scan to Configu
Page 89 and 90: Chapter 9: Managing the Mobile Devi
Page 103 and 104: Chapter 10: Managing Software Profi
Page 121 and 122: Chapter 11: Managing Mobile Devices
Page 131 and 132:
Chapter 11: Managing Mobile Devices
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Chapter 12: Managing Mobile Device
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Chapter 13: Managing Alert Profiles
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Chapter 14: Using Selection Criteri
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Chapter 15: Using the Task Schedule
Page 183 and 184:
Chapter 15: Using the Task Schedule
Page 185 and 186:
Appendix A: SSL Certificates 183
Page 187 and 188:
Appendix A: SSL Certificates 185 Ge
Page 189 and 190:
Appendix A: SSL Certificates 187 3
Page 191 and 192:
Appendix A: SSL Certificates 189 to
Page 193 and 194:
Appendix A: SSL Certificates 191 ke
Page 195 and 196:
Appendix B: Avalanche Services 193
Page 197 and 198:
Appendix C: Port Information 195 Mo
Page 199 and 200:
Glossary 197 Glossary ActiveSync Ad
Page 201 and 202:
Glossary 199 ESSID Exclusion Window
Page 203 and 204:
Glossary 201 Remote Control Scan to
Page 205 and 206:
Index 203 Index A activating Avalan
Page 207 and 208:
Index 205 scheduled settings 66 WLA
show all

Wavelink Avalanche Site Edition Java Console User Guide

Create successful ePaper yourself

Delete template?

Save as template?