view user manual (pdf) - dyna-flo control valves

More documents

Recommendations

Info

Preparing for Operation Assembly of the screw--type gland with plastic hose S S S S S Unscrew the sinter bronze silencer from the exhaust air opening on the underside of the housing. Screw the screw--type gland mentioned above into the exhaust air opening. Mount the above mentioned plastic hose on the screw--type gland and check the good fit. Fix the plastic hose with a cable strap to the fitting so that the opening faces downwards. Make sure that the hose has no kinks and the exhaust air can flow out unhindered. 3.3.2 Instructions for using positioners which are exposed to strong accelerations or vibrations Fittings under heavy mechanical stresses such as from breakaway flaps, violently shaking or vibrating valves, or steam jets can be exposed to strong acceleration forces far above those specified. This can result, in extreme cases, to a shifting of the friction clutch. For such cases the position controller equipped with a fixing device for the slip clutch with which adjustment due to the above mentioned influences can be prevented. The setting possibility is accessible below the black knurled wheel and is recognizable from slots on the yellow wheel. The zero point adjustment and the setting possibility of the slip clutch are identified by symbols on an additional plate (see figure 3-6, page 41). Procedure After you have mounted the position controller and commissioned it completely, you can set the slip clutch torque as follows: S S S S Plug a conventional 4 mm wide screwdriver into a slot in the yellow wheel. Then turn the yellow wheel to the left with the screwdriver until it snaps in audibly. This increases the torque of the slip clutch. A fixed slip clutch is recognizable from an approx. 1 mm wide gap between the yellow and black wheel. If you have to make a zero point setting, e.g. after changing the drive, please reduce the torque first by turning the yellow wheel to the right stop. After the zero point setting, you can fix the slip clutch as described above. 40 SIPART PS2 Manual A5E00074631-03
Preparing for Operation IP65 NEMA D--76181 Karlsruhe Type 4x SIPARTPS2 i/ p Posi ti oner 6DR5010--0NG00--0AA0 Iw = 4...20mA O Ta = --30 ... +80 C p = 1,4 ... 7bar F--Nr. N1--P212 --1234567 Made in France Iy SIA Alarm module module module Figure 3-6 Fixing device for the slip clutch External external travel detection Applications in which the measures described above are inadequate are also conceivable. This applies for instance with continuous and heavy vibration, increased or too low ambient temperatures and in the case of nuclear radiation. The separate attachment of position displacement sensor and controller unit can help here. A universal component is available which is suitable both for linear and rotary actuators. You require the following: S The external position detection system (order no. C73451- A430-D78). This consists of a SIPART-PS2- housing with integrated slip clutch, built-in potentiometer and various dummy plugs and seals. S or a Non-Contacting Position Sensor (e.g. 6DR4004--6N) S The controller unit, any positioner version. S S The EMC filter module, this is is a set together with cable clips and M-20 screw--type cable gland and has the order number C73451-A430-D23. The EMC filter module must be installed in the positioner. The installation instructions enclosed with the EMC filter module explain how to assemble the components. A 3-wire cable for connecting the components. This EMC filter module should always be used for the controller unit when any actuator--mounted potentiometer (resistance 10 kohms) is to be used instead of the external position detection system C73451-A430-D78. SIPART PS2 Manual A5E00074631-03 41
Page 1: Manual Edition 07/2003 sipart ps2 E
Page 4 and 5: Copyright e Siemens AG 2000 All rig
Page 6 and 7: 3.4.2 Connection in intrinsically s
Page 8 and 9: Information for the Operator This m
Page 10 and 11: Information for the Operator ! WARN
Page 12 and 13: Information for the Operator The fo
Page 14 and 15: Introduction Degree of protection E
Page 16 and 17: Introduction 1 2 4 3 1 Actuator 2 P
Page 18 and 19: Design and Functional Principle put
Page 20 and 21: Design and Functional Principle 2.2
Page 22 and 23: Design and Functional Principle Pos
Page 26 and 27: Design and Functional Principle 1 B
Page 28 and 29: Design and Functional Principle 5.
Page 30 and 31: Design and Functional Principle 6 1
Page 34 and 35: Design and Functional Principle The
Page 36 and 37: Design and Functional Principle 34
Page 38 and 39: Preparing for Operation 90 14 3x G1
Page 40 and 41: Preparing for Operation . NOTE The
Page 44 and 45: Preparing for Operation 3.3.3 Mount
Page 46 and 47: Preparing for Operation 2 17 16 12
Page 48 and 49: Preparing for Operation 3.3.6 Assem
Page 50 and 51: Preparing for Operation 15 14 4.2 9
Page 52 and 53: Preparing for Operation fastening B
Page 54 and 55: Preparing for Operation . NOTE Use
Page 56 and 57: Preparing for Operation Current out
Page 58 and 59: Preparing for Operation Non-hazardo
Page 60 and 61: Preparing for Operation Current out
Page 62 and 63: Preparing for Operation Non-hazardo
Page 64 and 65: Preparing for Operation SIA module
Page 66 and 67: Preparing for Operation Only a few
Page 68 and 69: Preparing for Operation 3. Switch o
Page 70 and 71: Preparing for Operation 4. Switch o
Page 72 and 73: Preparing for Operation The first l
Page 74 and 75: Preparing for Operation The initial
Page 76 and 77: Preparing for Operation 3.6.7 Autom
Page 78 and 79: Preparing for Operation 2 set lever
Page 80 and 81: Preparing for Operation 3.7 Copying
Page 82 and 83: Operation Figure 4-1 Meaning of the
Page 84 and 85: Operation 4.3 Operating modes The p
Page 86 and 87: Operation Manual 4-1 mode In this o
Page 88 and 89: Operation The following configurati
Page 90 and 91: Operation . NOTE After ”LWAY, ncS
Page 92 and 93:
Operation y=x 100 % Positioner 1 6.
Page 94 and 95:
Operation The setpoint vertex value
Page 96 and 97:
Operation 40.YCDO 41.YCUP Value for
Page 98 and 99:
Operation 48. TIM 49. LIM 50. STRK
Page 100 and 101:
Operation 4.5 Diagnosis 4.5.1 Diagn
Page 102 and 103:
Operation 4 A1CNT 5 A2CNT Alarm cou
Page 104 and 105:
Operation 31 VENT1 32 VENT2 Number
Page 106 and 107:
Operation Error Event code 1 Remain
Page 108 and 109:
Operation 8 Monitoring of the dead
Page 110 and 111:
Operation Upper line Lower line Mea
Page 112 and 113:
Operation 4.7 Optimization of the c
Page 114 and 115:
Care and Maintenance 8. Replace the
Page 116 and 117:
Technical Data ■ Technical data S
Page 118 and 119:
Technical Data ■ Technical data (
Page 120 and 121:
Technical Data ■ Technical data (
Page 122 and 123:
Scope of delivery 7.1 Ordering data
Page 124 and 125:
Scope of delivery 7.4 Scope of deli
Page 126 and 127:
Index Installation positions, favor
Page 128 and 129:
Appendix 9.2 Certificates 9.2.1 EC
Page 130 and 131:
Appendix 9.2.3 EC Type-Examination
Page 132 and 133:
Appendix 130 SIPART PS2 Manual A5E0
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Appendix 9.2.6 FM Approval Report (
Page 146 and 147:
Appendix 9.2.7 FM Approval Report 1
Page 148 and 149:
Appendix 9.2.8 CSA Certificate of C
Page 150 and 151:
Appendix 9.2.9 Control Drawing A5E0
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160:
show all

view user manual (pdf) - dyna-flo control valves

Create successful ePaper yourself

Delete template?

Save as template?