view user manual (pdf) - dyna-flo control valves

More documents

Recommendations

Info

Preparing for Operation 3.6.7 Automatic initialization (structograms) Linear actuator Rotary actuator Up Down Closed Open Figure 3-32 Direction of action of the actuators The initialization procedure should be taken from the following structogram (figure 3-33 to figure 3-36). The terms Open/Closed and up/down in the structogram refer to the direction of action of the actuators as illustrated in figure 3-32. configure start: press >5s 1 move the actuator into the travel range with: piezo valve 1 opens continue with: RUN 1 dy > 4 % ? no t>60s? no yes yes piezo valve 2 opens dy > 4 % ? no t>60s? no yes yes 2 <strong>manual</strong> intervention Figure 3-33 Automatic initialization, part 1 74 SIPART PS2 Manual A5E00074631-03
Preparing for Operation 2 actuator moves into closed position RUN 2 tolerance band 4% < dw < 10% ? yes no turn slip clutch until 0 appears in the bottom line of the display continue with: actuator moves into open position hard stop up < 97 % ? no yes span up--dw > 25 % ? no continue with: check mechanics 1 3 yes continue with: <strong>manual</strong> intervention Figure 3-34 Automatic initialization part 2 (in rotary actuators) SIPART PS2 Manual A5E00074631-03 75
Page 1:
Manual Edition 07/2003 sipart ps2 E
Page 4 and 5:
Copyright e Siemens AG 2000 All rig
Page 6 and 7:
3.4.2 Connection in intrinsically s
Page 8 and 9:
Information for the Operator This m
Page 10 and 11:
Information for the Operator ! WARN
Page 12 and 13:
Information for the Operator The fo
Page 14 and 15:
Introduction Degree of protection E
Page 16 and 17:
Introduction 1 2 4 3 1 Actuator 2 P
Page 18 and 19:
Design and Functional Principle put
Page 20 and 21:
Design and Functional Principle 2.2
Page 22 and 23:
Design and Functional Principle Pos
Page 24 and 25:
Design and Functional Principle 2.3
Page 26 and 27: Design and Functional Principle 1 B
Page 28 and 29: Design and Functional Principle 5.
Page 30 and 31: Design and Functional Principle 6 1
Page 32 and 33: Design and Functional Principle 1.1
Page 34 and 35: Design and Functional Principle The
Page 36 and 37: Design and Functional Principle 34
Page 38 and 39: Preparing for Operation 90 14 3x G1
Page 40 and 41: Preparing for Operation . NOTE The
Page 42 and 43: Preparing for Operation Assembly of
Page 44 and 45: Preparing for Operation 3.3.3 Mount
Page 46 and 47: Preparing for Operation 2 17 16 12
Page 48 and 49: Preparing for Operation 3.3.6 Assem
Page 50 and 51: Preparing for Operation 15 14 4.2 9
Page 52 and 53: Preparing for Operation fastening B
Page 54 and 55: Preparing for Operation . NOTE Use
Page 56 and 57: Preparing for Operation Current out
Page 58 and 59: Preparing for Operation Non-hazardo
Page 60 and 61: Preparing for Operation Current out
Page 62 and 63: Preparing for Operation Non-hazardo
Page 64 and 65: Preparing for Operation SIA module
Page 66 and 67: Preparing for Operation Only a few
Page 68 and 69: Preparing for Operation 3. Switch o
Page 70 and 71: Preparing for Operation 4. Switch o
Page 72 and 73: Preparing for Operation The first l
Page 74 and 75: Preparing for Operation The initial
Page 78 and 79: Preparing for Operation 2 set lever
Page 80 and 81: Preparing for Operation 3.7 Copying
Page 82 and 83: Operation Figure 4-1 Meaning of the
Page 84 and 85: Operation 4.3 Operating modes The p
Page 86 and 87: Operation Manual 4-1 mode In this o
Page 88 and 89: Operation The following configurati
Page 90 and 91: Operation . NOTE After ”LWAY, ncS
Page 92 and 93: Operation y=x 100 % Positioner 1 6.
Page 94 and 95: Operation The setpoint vertex value
Page 96 and 97: Operation 40.YCDO 41.YCUP Value for
Page 98 and 99: Operation 48. TIM 49. LIM 50. STRK
Page 100 and 101: Operation 4.5 Diagnosis 4.5.1 Diagn
Page 102 and 103: Operation 4 A1CNT 5 A2CNT Alarm cou
Page 104 and 105: Operation 31 VENT1 32 VENT2 Number
Page 106 and 107: Operation Error Event code 1 Remain
Page 108 and 109: Operation 8 Monitoring of the dead
Page 110 and 111: Operation Upper line Lower line Mea
Page 112 and 113: Operation 4.7 Optimization of the c
Page 114 and 115: Care and Maintenance 8. Replace the
Page 116 and 117: Technical Data ■ Technical data S
Page 118 and 119: Technical Data ■ Technical data (
Page 120 and 121: Technical Data ■ Technical data (
Page 122 and 123: Scope of delivery 7.1 Ordering data
Page 124 and 125: Scope of delivery 7.4 Scope of deli
Page 126 and 127:
Index Installation positions, favor
Page 128 and 129:
Appendix 9.2 Certificates 9.2.1 EC
Page 130 and 131:
Appendix 9.2.3 EC Type-Examination
Page 132 and 133:
Appendix 130 SIPART PS2 Manual A5E0
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Appendix 9.2.6 FM Approval Report (
Page 146 and 147:
Appendix 9.2.7 FM Approval Report 1
Page 148 and 149:
Appendix 9.2.8 CSA Certificate of C
Page 150 and 151:
Appendix 9.2.9 Control Drawing A5E0
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160:
show all

view user manual (pdf) - dyna-flo control valves

Create successful ePaper yourself

Delete template?

Save as template?