view user manual (pdf) - dyna-flo control valves

More documents

Recommendations

Info

Preparing for Operation SIA module Non-hazardous area Hazardous area zone 2 SIA module 6DR4004-6G + 8.2 V 31 32 2K1 10K Fault message + 8.2 V 41 42 Limit value A1 + 8.2 V 51 52 Limit value A2 Figure 3-31 SIA module 6DR4004-6G, EEx n 3.5 Pneumatic Connection ! WARNING For reasons of safety, the pneumatic power may only be supplied after assembly when the positioner is switched to operating level P manual operation with electrical signal applied (as--delivered state, see figure 4-4, page 82). . NOTE Note the air quality! Oil-free industrial air, solid content < 30 μm, pressure dew point 20 K below the lowest ambient temperature (chapter 7 “Technical Data”, page 119). S S Connect a manometer block for supply air and actuating pressure if necessary. Connection by female thread G 1/4 DIN 45141 or 1/4” NPT: P Z Supply air 1.4 to 7 bar Y1 actuating pressure 1 for single- and double-acting actuators Y2 actuating pressure 2 for double-acting actuators E exhaust air outlet (remove silencer if necessary) see figure 2-3 and 2-4, page 18. 62 SIPART PS2 Manual A5E00074631-03
Preparing for Operation S S .Safety position when the electric power supply fails: single-acting: Y1 deaerated double-acting: Y1 Max. Actuating pressure (supply air pressure) Y2 deaerated Connect actuating pressure Y1 or Y2 (only in double-acting actuators) according to the desired safety position. S Connect supply air to P Z . . NOTE In order for spring-loaded pneumatic actuators to be able to reliably exploit the maximum possible travel, the supply pressure must be sufficiently greater than the maximum required final pressure of the actuator. After installing the device, check the pneumatic connections of the entire assembly for leakage. Any leakage would cause not only continuous consumption of compressed air but also would cause the positioner to continually endeavor to compensate for the variance in position, leading in time to premature wear of the whole control mechanism. 3.6 Commissioning Once the positioner has been fitted to a pneumatic actuator, it must be provided with electrical and pneumatic auxiliary power. Then you can then adapt the position controller to the respective actuator by parameterizing and initializing it. Mode” operating mode (which can also if necessary be attained by ”PRST”) -- ”NOINI” will flash. If the positioner has not been initialized it will be in the ”P Manual Mode” operating mode (which can also if necessary be attained by ”PRST”) -- ”NOINI” will flash. This initialization can be effected in three different ways: S Automatic initialization Initialization takes place automatically. Hereby the positioner determines the direction of action, the stem travel and the angle of rotation, the travel times of the actuator one after the other and adapts the control parameters to the dynamic behavior of the actuator. S S Manual initialization The stem travel or angle of rotation of the actuator can be set manually, the other parameters are determined as in automatic initialization. This function is useful in actuators with soft limit stops. Copying initialization data (positioner exchange) In the devices with HART function the initialization data of a positioner can be read out and copied to another positioner. This enables a defective device to be changed without having to interrupt an ongoing process by initialization. SIPART PS2 Manual A5E00074631-03 63
Page 1:
Manual Edition 07/2003 sipart ps2 E
Page 4 and 5:
Copyright e Siemens AG 2000 All rig
Page 6 and 7:
3.4.2 Connection in intrinsically s
Page 8 and 9:
Information for the Operator This m
Page 10 and 11:
Information for the Operator ! WARN
Page 12 and 13:
Information for the Operator The fo
Page 14 and 15: Introduction Degree of protection E
Page 16 and 17: Introduction 1 2 4 3 1 Actuator 2 P
Page 18 and 19: Design and Functional Principle put
Page 20 and 21: Design and Functional Principle 2.2
Page 22 and 23: Design and Functional Principle Pos
Page 26 and 27: Design and Functional Principle 1 B
Page 28 and 29: Design and Functional Principle 5.
Page 30 and 31: Design and Functional Principle 6 1
Page 34 and 35: Design and Functional Principle The
Page 36 and 37: Design and Functional Principle 34
Page 38 and 39: Preparing for Operation 90 14 3x G1
Page 40 and 41: Preparing for Operation . NOTE The
Page 42 and 43: Preparing for Operation Assembly of
Page 44 and 45: Preparing for Operation 3.3.3 Mount
Page 46 and 47: Preparing for Operation 2 17 16 12
Page 48 and 49: Preparing for Operation 3.3.6 Assem
Page 50 and 51: Preparing for Operation 15 14 4.2 9
Page 52 and 53: Preparing for Operation fastening B
Page 54 and 55: Preparing for Operation . NOTE Use
Page 56 and 57: Preparing for Operation Current out
Page 58 and 59: Preparing for Operation Non-hazardo
Page 60 and 61: Preparing for Operation Current out
Page 62 and 63: Preparing for Operation Non-hazardo
Page 66 and 67: Preparing for Operation Only a few
Page 68 and 69: Preparing for Operation 3. Switch o
Page 70 and 71: Preparing for Operation 4. Switch o
Page 72 and 73: Preparing for Operation The first l
Page 74 and 75: Preparing for Operation The initial
Page 76 and 77: Preparing for Operation 3.6.7 Autom
Page 78 and 79: Preparing for Operation 2 set lever
Page 80 and 81: Preparing for Operation 3.7 Copying
Page 82 and 83: Operation Figure 4-1 Meaning of the
Page 84 and 85: Operation 4.3 Operating modes The p
Page 86 and 87: Operation Manual 4-1 mode In this o
Page 88 and 89: Operation The following configurati
Page 90 and 91: Operation . NOTE After ”LWAY, ncS
Page 92 and 93: Operation y=x 100 % Positioner 1 6.
Page 94 and 95: Operation The setpoint vertex value
Page 96 and 97: Operation 40.YCDO 41.YCUP Value for
Page 98 and 99: Operation 48. TIM 49. LIM 50. STRK
Page 100 and 101: Operation 4.5 Diagnosis 4.5.1 Diagn
Page 102 and 103: Operation 4 A1CNT 5 A2CNT Alarm cou
Page 104 and 105: Operation 31 VENT1 32 VENT2 Number
Page 106 and 107: Operation Error Event code 1 Remain
Page 108 and 109: Operation 8 Monitoring of the dead
Page 110 and 111: Operation Upper line Lower line Mea
Page 112 and 113: Operation 4.7 Optimization of the c
Page 114 and 115:
Care and Maintenance 8. Replace the
Page 116 and 117:
Technical Data ■ Technical data S
Page 118 and 119:
Technical Data ■ Technical data (
Page 120 and 121:
Technical Data ■ Technical data (
Page 122 and 123:
Scope of delivery 7.1 Ordering data
Page 124 and 125:
Scope of delivery 7.4 Scope of deli
Page 126 and 127:
Index Installation positions, favor
Page 128 and 129:
Appendix 9.2 Certificates 9.2.1 EC
Page 130 and 131:
Appendix 9.2.3 EC Type-Examination
Page 132 and 133:
Appendix 130 SIPART PS2 Manual A5E0
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Appendix 9.2.6 FM Approval Report (
Page 146 and 147:
Appendix 9.2.7 FM Approval Report 1
Page 148 and 149:
Appendix 9.2.8 CSA Certificate of C
Page 150 and 151:
Appendix 9.2.9 Control Drawing A5E0
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160:
show all

view user manual (pdf) - dyna-flo control valves

Create successful ePaper yourself

Delete template?

Save as template?