view user manual (pdf) - dyna-flo control valves

More documents

Recommendations

Info

Preparing for Operation Non-hazardous area Hazardous area zone 1 or zone 2 EEx J + 4to20mA 2 3 4 5 Positioner 6DR5210-xExxx 6DR5220-xExxx 6DR5211-xExxx Intrinsically safe power source 6 7 8 9 10 E A Digital input 1 HART Communicator Figure 3-20 Two-wire connection, EEx i Non-hazardous area Hazardous area zone 1 or zone 2 EEx U + 18 to 30 V 2 3 4 5 Positioner 6DR5210-xExxx 6DR5220-xExxx 6DR5211-xExxx EEx J Intrinsically safe power source + *) 4to20mA *) 6 7 8 9 10 E A Digital input 1 HART Communicator *) Only for three-wire connection Figure 3-21 Three-/four--wire connection, EEx i 56 SIPART PS2 Manual A5E00074631-03
Preparing for Operation Split-range intrinsically safe feed sources Non-hazardous area Power supply EEx EEx U I total setting range Iy L+ Iy M M Hazardous area zone 1 or zone 2 +18to30V +0/4 to 20 mA # Instrument 1 Positioner 6DR5210--xExxx 6DR5220--xExxx 6DR5211--xExxx setting range 1 Digital input 1 Instrument 2 Positioner 6DR5210--xExxx 6DR5220--xExxx 6DR5211--xExxx setting range 1 # Digital input 1 Figure 3-22 Series circuit of two positioners, e.g. split range (separate power supply), EEx i SIPART PS2 Manual A5E00074631-03 57
Page 1:
Manual Edition 07/2003 sipart ps2 E
Page 4 and 5:
Copyright e Siemens AG 2000 All rig
Page 6 and 7:
3.4.2 Connection in intrinsically s
Page 8 and 9: Information for the Operator This m
Page 10 and 11: Information for the Operator ! WARN
Page 12 and 13: Information for the Operator The fo
Page 14 and 15: Introduction Degree of protection E
Page 16 and 17: Introduction 1 2 4 3 1 Actuator 2 P
Page 18 and 19: Design and Functional Principle put
Page 20 and 21: Design and Functional Principle 2.2
Page 22 and 23: Design and Functional Principle Pos
Page 26 and 27: Design and Functional Principle 1 B
Page 28 and 29: Design and Functional Principle 5.
Page 30 and 31: Design and Functional Principle 6 1
Page 34 and 35: Design and Functional Principle The
Page 36 and 37: Design and Functional Principle 34
Page 38 and 39: Preparing for Operation 90 14 3x G1
Page 40 and 41: Preparing for Operation . NOTE The
Page 42 and 43: Preparing for Operation Assembly of
Page 44 and 45: Preparing for Operation 3.3.3 Mount
Page 46 and 47: Preparing for Operation 2 17 16 12
Page 48 and 49: Preparing for Operation 3.3.6 Assem
Page 50 and 51: Preparing for Operation 15 14 4.2 9
Page 52 and 53: Preparing for Operation fastening B
Page 54 and 55: Preparing for Operation . NOTE Use
Page 56 and 57: Preparing for Operation Current out
Page 60 and 61: Preparing for Operation Current out
Page 62 and 63: Preparing for Operation Non-hazardo
Page 64 and 65: Preparing for Operation SIA module
Page 66 and 67: Preparing for Operation Only a few
Page 68 and 69: Preparing for Operation 3. Switch o
Page 70 and 71: Preparing for Operation 4. Switch o
Page 72 and 73: Preparing for Operation The first l
Page 74 and 75: Preparing for Operation The initial
Page 76 and 77: Preparing for Operation 3.6.7 Autom
Page 78 and 79: Preparing for Operation 2 set lever
Page 80 and 81: Preparing for Operation 3.7 Copying
Page 82 and 83: Operation Figure 4-1 Meaning of the
Page 84 and 85: Operation 4.3 Operating modes The p
Page 86 and 87: Operation Manual 4-1 mode In this o
Page 88 and 89: Operation The following configurati
Page 90 and 91: Operation . NOTE After ”LWAY, ncS
Page 92 and 93: Operation y=x 100 % Positioner 1 6.
Page 94 and 95: Operation The setpoint vertex value
Page 96 and 97: Operation 40.YCDO 41.YCUP Value for
Page 98 and 99: Operation 48. TIM 49. LIM 50. STRK
Page 100 and 101: Operation 4.5 Diagnosis 4.5.1 Diagn
Page 102 and 103: Operation 4 A1CNT 5 A2CNT Alarm cou
Page 104 and 105: Operation 31 VENT1 32 VENT2 Number
Page 106 and 107: Operation Error Event code 1 Remain
Page 108 and 109:
Operation 8 Monitoring of the dead
Page 110 and 111:
Operation Upper line Lower line Mea
Page 112 and 113:
Operation 4.7 Optimization of the c
Page 114 and 115:
Care and Maintenance 8. Replace the
Page 116 and 117:
Technical Data ■ Technical data S
Page 118 and 119:
Technical Data ■ Technical data (
Page 120 and 121:
Technical Data ■ Technical data (
Page 122 and 123:
Scope of delivery 7.1 Ordering data
Page 124 and 125:
Scope of delivery 7.4 Scope of deli
Page 126 and 127:
Index Installation positions, favor
Page 128 and 129:
Appendix 9.2 Certificates 9.2.1 EC
Page 130 and 131:
Appendix 9.2.3 EC Type-Examination
Page 132 and 133:
Appendix 130 SIPART PS2 Manual A5E0
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Appendix 9.2.6 FM Approval Report (
Page 146 and 147:
Appendix 9.2.7 FM Approval Report 1
Page 148 and 149:
Appendix 9.2.8 CSA Certificate of C
Page 150 and 151:
Appendix 9.2.9 Control Drawing A5E0
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160:
show all

view user manual (pdf) - dyna-flo control valves

Create successful ePaper yourself

Delete template?

Save as template?