SERVICE MANUAL - Alarko Carrier

More documents

Recommendations

Info

No. Part name Procedures Remarks 1 Front panel 4) Press “ ” part under the front panel and remove hooks of the front panel from the installation plate. Installation plate Front panel Pull here Press here Press here Press 5) Remove the front panel fixing screws. (2 pcs.) 6) Press the electric parts box with the right thumb while pulling the both sides of the front panel toward you. Electric dust collector Electric dust collector Holder Holder Protrusion Protrusion 1) Press three center positions and two lower center positions of the air outlet, and then hang the hanging hooks (4 pcs.) at the top side of the front panel to the rear plate. 2) Insert the electric dust collector and left and right air filters. Press in the electric dust collector until the protrusions on both sides are completely inserted into the holders. If installation is incomplete, the FILTER indicator (orange) may light. 3) Tighten two screws. • Incomplete hanging or incomplete pressing may cause a dewdrops or generation of a fluttering sound. – 108 –
No. Part name Procedures Remarks 2 High voltage generator 1) Follow to the procedure in the item 1 . 2) Remove the drain guide. 3) To remove the air ionizer from the back body, pull it toward you while pressing down on its left and right claws. Disconnect the two leads (black) connected to the air ionizer from where they are fitted into the other components. (Caution: do not remove the Faston.) 4) Disconnect the connectors of the high-voltage generator, and disconnect the four leads from where they are fitted into the other components. 5) Remove the fixing screw which secures the high voltage generator, and remove the high voltage generator from the evaporator. Connector Drain guide Air ionizer Press the claw here Press the claw here Screw Pull here 1) Insert the high voltage generator straight into the evaporator, and secure it using the fixing screw. Check whether the leads have been completely inserted. 2) Pass the leads of the high voltage generator through the area designated and insert them into its connectors. 3) Attach the air ionizer to the back body, and pass the two leads (black) through the area designated on the electric parts box assembly. 4) Attach the drain guide. Claw Claw Claw – 109 –
Page 1 and 2:
FILE NO. A05-011-1 Revised on May/2
Page 3 and 4:
1. SAFETY PRECAUTIONS Revised For g
Page 5 and 6:
2. SPECIFICATIONS The indoor and ou
Page 7 and 8:
RAS-M10GKCVP-E, RAS-M13GKCVP-E, RAS
Page 9 and 10:
Outdoor Unit : RAS-4M27GAV-E Power
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Outdoor Unit : RAS-4M27GACV-E Powe
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
2-2-1. Operation Characteristic Cur
Page 25 and 26:
Table 3-2-1 Thicknesses of annealed
Page 27 and 28:
43˚ to 45˚ Table 3-2-6 Flare and
Page 29 and 30:
3-4. Recharging of Refrigerant When
Page 31 and 32:
2. Characteristics required for flu
Page 33 and 34:
4-2. Outdoor Unit RAS-4M27GAV-E, RA
Page 35 and 36:
5-2. Outdoor Unit RAS-4M27GAV-E, RA
Page 37 and 38:
7. REFRIGERANT CYCLE DIAGRAM RAS-B1
Page 39 and 40:
RAS-B10GKVP-E, RAS-B13GKVP-E, RAS-B
Page 41 and 42:
Outdoor Unit : RAS-4M27GAV-E Tempe
Page 43 and 44:
Outdoor Unit : RAS-3M26GAV-E Tempe
Page 45 and 46:
8. CONTROL BLOCK DIAGRAM 8-1. Indoo
Page 47 and 48:
8-2. Outdoor Unit (Inverter Assembl
Page 49 and 50:
9-2. Operation Description 9-2. 1.
Page 51 and 52:
Item Operation flow and applicable
Page 53 and 54:
Item 2. Indoor fan motor control CO
Page 55 and 56:
Item Operation flow and applicable
Page 57 and 58: Item 6. Release protective control
Page 59 and 60: Item Operation flow and applicable
Page 61 and 62: Item Operation flow and applicable
Page 63 and 64: Item 14. Pulse motor valve (P.M.V.)
Page 65 and 66: Item 16. Clean operation release Op
Page 67 and 68: 9-3. Auto Restart Function This ind
Page 69 and 70: 9-5. Remote Controller and Its Fuct
Page 71 and 72: 9-6. Hi-POWER Mode ([Hi-POWER] butt
Page 73 and 74: 10-2. Optional Parts, Accessories a
Page 75 and 76: 10-3. Indoor Unit 10-3-1. Installat
Page 77 and 78: CAUTION • Be sure to refer to the
Page 79 and 80: CAUTION • Bind the auxiliary pipe
Page 81 and 82: 10-4-5. Refrigerant Piping Connecti
Page 83 and 84: 10-4-7. Evacuating After the piping
Page 85 and 86: 10-4-10. Miswiring (Mispiping) Chec
Page 87 and 88: 11. HOW TO DIAGNOSE THE TROUBLE The
Page 89 and 90: 11-3. Self-Diagnosis by Remote Cont
Page 91 and 92: Block distinction Check code Block
Page 93 and 94: (3) Only the indoor motor fan does
Page 95 and 96: (5) Troubleshooting for remote cont
Page 97 and 98: 11-5. Trouble Diagnosis by Outdoor
Page 99 and 100: 11-6-2. How to Check Whether the Mi
Page 101 and 102: Diagnosis/Process flowchart Item Co
Page 103 and 104: 11-8-2. P.C. Board Layout GND +12V
Page 105 and 106: 11-8-5. Checking Method for Each Pa
Page 107: 12. HOW TO REPLACE THE MAIN PARTS W
Page 111 and 112: No. Part name Procedures Remarks 4
Page 113 and 114: No. Part name Procedures Remarks 7
Page 115 and 116: 12-2. Microcomputer No. Part name P
Page 117 and 118: No. Part name Procedure Remarks 3 C
Page 119 and 120: No. Part name Procedure Remarks 7 P
Page 121 and 122: - 121 -
Page 123 and 124: 13. EXPLODED VIEWS AND PARTS LIST 1
Page 125 and 126: 13-2. Outdoor Unit 4 6 41, 42 35 23
Page 127 and 128: 13-3. P.C. Board Layout RAS-4M27GAV
Page 129 and 130: RAS-3M26GAV-E 707 710 715 700 705 T
show all

SERVICE MANUAL - Alarko Carrier

Create successful ePaper yourself

Delete template?

Save as template?