Modifications for the ICOM - RogerK
Modifications for the ICOM - RogerK
Modifications for the ICOM - RogerK
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
19-07-1998(IC-W2E) IC-W2E Expand frequencyDisplay test / Rx Expanding;Turn <strong>the</strong> porto off, press <strong>the</strong> #,3 and <strong>the</strong> B, hold this buttons, now turn on your porto (Red Button), you will see now all <strong>the</strong>functions who are in <strong>the</strong> lcd display.When you quit pressing <strong>the</strong> #,3 and <strong>the</strong> B button, your porto can now go (On Display) from 100khz 999.90Mhz at <strong>the</strong> 2mDisplay, and on <strong>the</strong> 70cm Display he will go from 100khz 1310.00Mhz, of course he will not recieve from 100khz 1310Mhz, but <strong>the</strong> low vfo receive at least from 126Mhz 190Mhz, <strong>the</strong> high vfo receive at least from 390Mhz 999Mhz, withsome steps between 390Mhz 999Mhz where he not receive signals, because <strong>the</strong> vfo is out of his lock.Enter Freq via keyboard;When you enter a freq (in vfo mode) by pressing enter (ENT) you will see that you can press only <strong>the</strong> last 3 digits, this is simplyto change by pressing <strong>the</strong> function button (above <strong>the</strong> ptt) and <strong>the</strong> set (8) button, push now with <strong>the</strong> ^/scan until you see on <strong>the</strong>display 'PL', now you can dial 1 - 10 -100 = 1Mhz - 10Mhz - 100Mhz, set this option to 100 (dial), now you press <strong>the</strong> clr (*).Done !!!!If you now press enter (#) (in vfo mode) you will see that you now can press <strong>the</strong> whole freq. The same <strong>for</strong> <strong>the</strong> o<strong>the</strong>r vfo, thisgo's <strong>the</strong> same <strong>for</strong> 1Mhz - 10Mhz PL function.Steps with <strong>the</strong> dial;Dialing a freq go's with steps in Khz, by pressing <strong>the</strong> function key (above <strong>the</strong> ptt) <strong>the</strong> steps will be now steps of 10Mhz.Here are some RX reports by JBE;RX FreqSensitivity (12db sinad)-------------------------------------------------126MHz- 111dBm136MHz- 123dBm145MHz - 125dBm160MHz- 123dBm174MHz- 110dBm190MHz - 67dBm Low vfo-------------------------------------------------390MHz- 108dBm430MHz - 124dBm452MHz- 105dBm470MHz- 103dBm485MHz- 104dBm850MHz- 110dBm900MHz- 116dBm925MHz- 114dBm935MHz- 112dBm950MHz- 107dBm999MHz - 96dBm Hi vfo-------------------------------------------------This modification is read 583 times.top of page19-07-1998(IC-W31) IC-W31E Frequenzbereichs-Erweiterung1. Geraet auschalten2. "B"- und "#"-Taste gleichzeitig gedrueckt halten und dabei das Geraet einschalten.(Anzeige VHF: 50,000 - 299,990 MHz; UHF: 300,000 - 999,990 MHz.Empfindlichkeit im unteren Bereich nicht sehr gut, im oberen dagegen ueberraschend.)Nach einem kompletten RESET ist die Bereichserweiterung deaktiviert.Nach dieser Erweiterung erscheint im SET-Menue ein weiterer Punkt, welcher PLACE heisst. Er bietet die Auswahl "1", "10" und"100" fuer jedes Band. Damit kann gewaehlt werden, ab welcher MHz-Stelle die Eingabe beginnt. Bei "1" ab der Einer-MHz-Stelle, bei "10" ab der 10er-MHz-Stelle und bei "100" kann die Frequenz komplett eingegeben werden (fuehrende Null bei VHFnicht vergessen!).This modification is read 649 times.top of page
Change language