Digital Servo Amplifier SERVOSTAR 400 - BIBUS SK, sro

More documents

Recommendations

Info

Installation 07/03 Kollmorgen This page has been deliberately left blank. 34 SERVOSTAR ® 400 Installation manual
Kollmorgen 07/03 Installation 2.4 Setup software 2.4.1 General This chapter describes the installation of the setup software DRIVE.EXE for the SERVOSTAR 400 digital servo amplifiers. We offer training and familiarization courses on request. 2.4.1.1 Use as directed The operator software is intended to be used for altering and storing the operating parameters for the SERVOSTAR 400 series of servo amplifiers. The attached servo amplifier is commissioned with the assistance of the software - during this process the drive can be controlled directly by the service functions. Only professional personnel who have the relevant expertise described on Page 9 are permitted to carry out online parameter setting for a drive which is running. Sets of data which are stored on data media are not safe against unintended alteration by other persons. After loading a set of data you must therefore check all parameters thoroughly before enabling the servo amplifier. 2.4.1.2 Software description The servo amplifiers must be adapted to the requirements of your installation. Usually you will not have to carry out this parameter setting yourself on the amplifier, but on a PC, with the assistance of the operator software. The PC is connected to the servo amplifier by a null-modem (serial) cable. The setup software provides the communication between the PC and SERVOSTAR 400. You will find the setup software on the accompanying CD-ROM and in the download section of the Danaher Motion web appearance. With very little effort you can alter parameters and immediately observe the effect on the drive, since there is a continuous (online) connection to the amplifier. At the same time, important actual values are read out from the amplifier and displayed on the PC monitor (oscilloscope function). Any interface modules which may be built into the amplifier are automatically recognized, and the additional parameters which are required for position control or motion-block definition are made available. Sets of data can be stored on data media (archived) and loaded again. You can also print out the data sets. We provide you with motor-specific default sets of data for all the reasonable combinations of servo amplifier and motor. In most applications you will be able to use these default values to get your drive running without any problems. SERVOSTAR ® 400 Installation manual 35
Page 1 and 2: www.DanaherMotion.com Digital Servo
Page 3 and 4: Kollmorgen 07/03 Contents Page Cont
Page 5 and 6: Kollmorgen 07/03 Safety Instruction
Page 7 and 8: Kollmorgen 07/03 UL and cUL- Confor
Page 9 and 10: Kollmorgen 07/03 General 1 General
Page 11 and 12: Kollmorgen 07/03 General 1.3 Namepl
Page 13 and 14: Kollmorgen 07/03 General 1.4.4 Digi
Page 15 and 16: Kollmorgen 07/03 General 1.5 Block
Page 17 and 18: Kollmorgen 07/03 General 1.7 Techni
Page 19 and 20: Kollmorgen 07/03 General 1.7.5 LED
Page 21 and 22: Kollmorgen 07/03 General 1.11 Switc
Page 23 and 24: Kollmorgen 07/03 Installation 2 Ins
Page 25 and 26: Kollmorgen 07/03 Installation 2.2.1
Page 27 and 28: Kollmorgen 07/03 Installation The f
Page 33: Kollmorgen 07/03 Installation 2.3.5
Page 37 and 38: Kollmorgen 07/03 Interfaces 3 Inter
Page 39 and 40: Kollmorgen 07/03 Interfaces 3.3 Ext
Page 41 and 42: Kollmorgen 07/03 Interfaces 3.5 Con
Page 43 and 44: Kollmorgen 07/03 Interfaces 3.5.3 D
Page 45 and 46: Kollmorgen 07/03 Interfaces 3.6 Enc
Page 47 and 48: Kollmorgen 07/03 Interfaces 3.7 RS2
Page 49 and 50: Kollmorgen 07/03 Interfaces 3.8.1 C
Page 51 and 52: Kollmorgen 07/03 Interfaces 3.9.2 C
Page 53 and 54: Kollmorgen 07/03 Interfaces 3.10.2
Page 55 and 56: Kollmorgen 07/03 Commissioning 4 Co
Page 57 and 58: Kollmorgen 07/03 Commissioning 4.2
Page 59 and 60: Kollmorgen 07/03 Commissioning 4.2.
Page 61 and 62: Kollmorgen 07/03 Commissioning 4.4
Page 63 and 64: Kollmorgen 07/03 Accessories 5 Acce
Page 65 and 66: Kollmorgen 07/03 Accessories 5.3 Ex
Page 67 and 68: Kollmorgen 07/03 Appendix 6 Appendi
Page 69 and 70: Kollmorgen 07/03 Appendix Fault pos
Page 71 and 72: Kollmorgen 07/03 Appendix P P-contr
Page 73 and 74: Kollmorgen 07/03 Appendix This page

Digital Servo Amplifier SERVOSTAR 400 - BIBUS SK, sro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?