Digital Servo Amplifier SERVOSTAR 400 - BIBUS SK, sro

More documents

Recommendations

Info

Accessories 07/03 Kollmorgen 5.4 Add-on fan Electrical add-on fan for two axes to achieve rated power even under unfavourable ambient conditions, required for SERVOSTAR4x6. To mount the fan, just hook it in the designated slots at the bottom of the SERVOSTAR and screw the fixing bolt into the thread in the housing The electrical connection takes place automatically when mounting the fan. Please consider that a mounted fan increases the required space underneath the amplifier! (� p. 24) The drawing below shows, how the fan should be mounted. With an odd number of axes (master included), the fan must also cover the power supply unit at the master. Single master Master with 1 Axis module Master with 2 Axis modules 66 SERVOSTAR ® 400 Installation manual
Kollmorgen 07/03 Appendix 6 Appendix 6.1 Transport, storage, maintenace, disposal Transport: — only by qualified personnel — only in the manufacturer’s original recyclable packaging — avoid shocks — temperature -25 to +70°C, max. rate of change 20°C/hour — humidity max. 95% relative humidity, no condensation — the servo amplifiers contain electrostatically sensitive components — which can be damaged by incorrect handling. Discharge yourself — before touching the servo amplifier. Avoid contact with highly — insulating materials (artificial fabrics, plastic films etc.). — Place the servo amplifier on a conductive surface. — if the packaging is damaged, check the unit for visible damage. — In such a case, inform the shipper and the manufacturer. Packaging: — recyclable cardboard with inserts — dimensions SERVOSTAR 4xxA (HxWxD) 100x300x270 mm SERVOSTAR 4xxM (HxWxD) 150x300x270 mm — labelling instrument label on outside of box Storage : — only in the manufacturer’s original recyclable packaging — the servo amplifiers contain electrostatically sensitive components — which can be damaged by incorrect handling. Discharge yourself — before touching the servo amplifier. Avoid contact with highly — insulating materials (artificial fabrics, plastic films etc.). — Place the servo amplifier on a conductive surface. — max. stacking height: 8 cartons — storage temp. –25 to +55°C, max. rate of change 20°C/hr — humidity relative humidity max. 95%, no condensation — storage duration < 1 year without restriction > 1 year: capacitors must be re-formed before the servo amplifier is commissioned. To do this, remove all electrical connections and supply the servo amplifier for about 30 min. from 230V AC, single-phase, on terminals L2 / L3. Maintenance: — the instruments do not require any maintenance — opening the instruments invalidates the warranty Cleaning : — if the casing is dirty : cleaning with Isopropanol or similar do not immerse or spray — if there is dirt inside the unit: to be cleaned by the manufacturer — dirty protective grill (fan) : clean with a dry brush Disposal : — you can dismantle the servo amplifier into its principal components — by screwing it apart (aluminium heat sink, steel housing sections, — electronics boards) — disposal should be carried out by a certified disposal company. — We can give you suitable addresses on request. SERVOSTAR ® 400 Installation manual 67
Page 1 and 2:
www.DanaherMotion.com Digital Servo
Page 3 and 4:
Kollmorgen 07/03 Contents Page Cont
Page 5 and 6:
Kollmorgen 07/03 Safety Instruction
Page 7 and 8:
Kollmorgen 07/03 UL and cUL- Confor
Page 9 and 10:
Kollmorgen 07/03 General 1 General
Page 11 and 12:
Kollmorgen 07/03 General 1.3 Namepl
Page 13 and 14:
Kollmorgen 07/03 General 1.4.4 Digi
Page 15 and 16: Kollmorgen 07/03 General 1.5 Block
Page 17 and 18: Kollmorgen 07/03 General 1.7 Techni
Page 19 and 20: Kollmorgen 07/03 General 1.7.5 LED
Page 21 and 22: Kollmorgen 07/03 General 1.11 Switc
Page 23 and 24: Kollmorgen 07/03 Installation 2 Ins
Page 25 and 26: Kollmorgen 07/03 Installation 2.2.1
Page 27 and 28: Kollmorgen 07/03 Installation The f
Page 35 and 36: Kollmorgen 07/03 Installation 2.4 S
Page 37 and 38: Kollmorgen 07/03 Interfaces 3 Inter
Page 39 and 40: Kollmorgen 07/03 Interfaces 3.3 Ext
Page 41 and 42: Kollmorgen 07/03 Interfaces 3.5 Con
Page 43 and 44: Kollmorgen 07/03 Interfaces 3.5.3 D
Page 45 and 46: Kollmorgen 07/03 Interfaces 3.6 Enc
Page 47 and 48: Kollmorgen 07/03 Interfaces 3.7 RS2
Page 49 and 50: Kollmorgen 07/03 Interfaces 3.8.1 C
Page 51 and 52: Kollmorgen 07/03 Interfaces 3.9.2 C
Page 53 and 54: Kollmorgen 07/03 Interfaces 3.10.2
Page 55 and 56: Kollmorgen 07/03 Commissioning 4 Co
Page 57 and 58: Kollmorgen 07/03 Commissioning 4.2
Page 59 and 60: Kollmorgen 07/03 Commissioning 4.2.
Page 61 and 62: Kollmorgen 07/03 Commissioning 4.4
Page 63 and 64: Kollmorgen 07/03 Accessories 5 Acce
Page 65: Kollmorgen 07/03 Accessories 5.3 Ex
Page 69 and 70: Kollmorgen 07/03 Appendix Fault pos
Page 71 and 72: Kollmorgen 07/03 Appendix P P-contr
Page 73 and 74: Kollmorgen 07/03 Appendix This page
show all

Digital Servo Amplifier SERVOSTAR 400 - BIBUS SK, sro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?