GPT-3000 SERIES - FLT Geosystems

More documents

Recommendations

Info

2) Z Coordinate Calculation from Known Point Measuring Data[Example setting] Using coordinate data file6 SPECIAL MODE (Menu Mode)Operating procedure Operation Display1 After pressing [MENU] key, press [F4](P↓) key toget the menu on page 2.[MENU][F4]MENU 2/3F1:PROGRAMSF2:GRID FACTORF3:ILLUMINATION P↓2 Press the [F1] key. [F1]3 Press the [F3](Z COORD.) key. [F3]PROGRAMS 1/2F1:REMF2:MLMF3:Z COORD. P↓Z COORD.SETTINGF1:USE FILEF2:DON’T USE4 Press the [F1](USE FILE) key.5 Press the [F1](INPUT) key and enter the FileName.[F1][F1]Enter FN[F4]SELECT A FILEFN:_________INPUT LIST ––– ENTERZ COORD.SETTINGF1:OCC.PT INPUTF2:REF.MEAS6 Press the [F2] key. [F2]NOO1#PT#:_________7 Press the [F1](INPUT) key and enter the PointNumber in coordinate data file.8 Press the [F3](YES) key and enter the PointNumber in coordinate data file.[F1]Enter PT#[F4][F3]INPUT LIST NEZ ENTERN: 4.356 mE: 16.283 mZ: 1.553 m>OK ? [YES][NO]REFLECTOR HEIGHTINPUTR.HT: 0.000 mINPUT ––– ––– ENTER9 Press the [F1](INPUT) key and enter the height. [F1]Enter R. HT[F4]REFLECTOR HEIGHTINPUTR.HT: 0.000 mMEAS ––– NP/P –––10 Collimate a prism on the point and press the[F1](MEAS) key.Measuring starts. *1)Collimate P[F1]HR: 120°30'40"HD*[n] Measuring...6-9
6 SPECIAL MODE (Menu Mode)11 Press the [F4](CALC) key.*2)Z : Z coordinatedZ: Standard deviation12 Press the [F4](SET) key. *3)Z coordinate of the occupied point will be set.Bascksight point measuring screen will be shown.13 Press the [F3](YES) key.Horizontal angle will be set.The display returns to Programs 1/2 menu.[F4][F4][F3]HR: 120°30'40"HD: 12.345 mVD: 23.456 mNEXT ––– ––– CALCZ COORD. SETTINGZ : 1.234 mdZ : 0.002 m––– ––– BS SETBACKSIGHTHR: 23°20'40">OK?[YES][NO]PROGRAMS 1/2F1:REMF2:MLMF3:Z COORD. P↓*1) Measurement is Fine N-times measurement mode.*2) To measure other points, press the [F1](NEXT) key.*3) Pressing the [F3] key, the display will be changed alternately.6-10
Page 3 and 4:
FOREWORDThank you for purchasing th
Page 5 and 6:
Display for Safe UseIn order to enc
Page 7 and 8:
Laser Safety● Distance Measuremen
Page 10 and 11:
9.3.3 Deleting a File . . . . . . .
Page 12 and 13: 1 NOMENCLATURE AND FUNCTIONS1.1 Nom
Page 14 and 15: 1.2 Display●●●1 NOMENCLATURE
Page 16 and 17: 1.4 Function Key (Soft Key)1 NOMENC
Page 18 and 19: 1 NOMENCLATURE AND FUNCTIONS1.5 Sta
Page 20 and 21: 1 NOMENCLATURE AND FUNCTIONS●Tilt
Page 22 and 23: 2 PREPARATION FOR MEASUREMENT2.1 Po
Page 24 and 25: 2.3 Power Switch Key ON1 Confirm th
Page 26 and 27: 2.5 Vertical and Horizontal Angle T
Page 28 and 29: 2.6 How to Enter Alphanumeric chara
Page 30 and 31: 2 PREPARATION FOR MEASUREMENT2.8 La
Page 32 and 33: 3.2 Switching Horizontal Angle Righ
Page 34 and 35: 3.5 Repetition Angle Measurement3 A
Page 36 and 37: LOCK3.7 Compasses ( vertical angle)
Page 38 and 39: 4.3 Distance Measurement (Continuou
Page 40 and 41: 4 DISTANCE MEASUREMENT● Choose me
Page 42 and 43: 4.7 Offset Measurement4 DISTANCE ME
Page 44 and 45: 4 DISTANCE MEASUREMENTThe horizonta
Page 46 and 47: 4 DISTANCE MEASUREMENTAfter measuri
Page 48 and 49: 4 DISTANCE MEASUREMENT6 Measure the
Page 50 and 51: 4 DISTANCE MEASUREMENT6 Collimate t
Page 52 and 53: 5.2 Setting Height of the Instrumen
Page 54 and 55: 6 SPECIAL MODE (Menu Mode)By pressi
Page 56 and 57: 6 SPECIAL MODE (Menu Mode)Horizonta
Page 58 and 59: 6 SPECIAL MODE (Menu Mode)6.1.2 Mis
Page 60 and 61: 6 SPECIAL MODE (Menu Mode)The horiz
Page 64 and 65: 6 SPECIAL MODE (Menu Mode)6.1.4 Are
Page 66 and 67: 6 SPECIAL MODE (Menu Mode)When 3 or
Page 68 and 69: 6 SPECIAL MODE (Menu Mode)7 Collima
Page 70 and 71: 6 SPECIAL MODE (Menu Mode)3 Press t
Page 72 and 73: 6 SPECIAL MODE (Menu Mode)7 Press t
Page 74 and 75: 6 SPECIAL MODE (Menu Mode)6.4.5 Sel
Page 76 and 77: 6.5 Setting Contrast of DisplaySett
Page 78 and 79: 7 DATA COLLECTION●Data collect me
Page 80 and 81: 7 DATA COLLECTION7.1.2 Selecting a
Page 82 and 83: 7 DATA COLLECTION●Example for set
Page 84 and 85: 7 DATA COLLECTION*1) Refer to Secti
Page 86 and 87: 7.3 Data Collect Offset Measurement
Page 88 and 89: 7 DATA COLLECTION7.3.2 Distance Off
Page 90 and 91: 7 DATA COLLECTION7.3.3 Plane Offset
Page 92 and 93: 7 DATA COLLECTION7.3.4 Column Offse
Page 94 and 95: 7.5 Point to Line MeasurementIn thi
Page 96 and 97: 7 DATA COLLECTION7.6 Editing PCODE
Page 98 and 99: 8 LAYOUTLAYOUT mode has two functio
Page 100 and 101: 8.1 Preparation8 LAYOUT8.1.1 Settin
Page 102 and 103: 8 LAYOUT8.1.3 Setting Occupied Poin
Page 104 and 105: 8 LAYOUT8.1.4 Setting Backsight Poi
Page 106 and 107: 8.2 Executing a LayoutThe following
Page 108 and 109: 8 LAYOUT8.2.1 Layout of Coordinates
Page 110 and 111: 8 LAYOUT6 Press the [F4](ENTER) key
Page 112 and 113:
8 LAYOUT5 Enter instrument height i
Page 114 and 115:
● Viewing PT# LIST8 LAYOUTYou can
Page 116 and 117:
9.1 Display Internal Memory StatusT
Page 118 and 119:
● To edit the data in searching m
Page 120 and 121:
9 MEMORY MANAGER MODE9.2.3 PCODE LI
Page 122 and 123:
9 MEMORY MANAGER MODE9.3.1 Rename a
Page 124 and 125:
9.4 Coordinate Data Direct Key Inpu
Page 126 and 127:
9.5 Delete a Coordinate Data from a
Page 128 and 129:
9.7 Data Communications9 MEMORY MAN
Page 130 and 131:
9 MEMORY MANAGER MODE9.7.3 Setting
Page 132 and 133:
10 SET AUDIO MODE10 SET AUDIO MODET
Page 134 and 135:
12 SETTING ATMOSPHERIC CORRECTION12
Page 136 and 137:
12 SETTING ATMOSPHERIC CORRECTIONAt
Page 138 and 139:
12-512 SETTING ATMOSPHERIC CORRECTI
Page 140 and 141:
14 POWER SOURCE AND CHARGING14.1 On
Page 142 and 143:
15 DETACH/ATTACH OF TRIBRACH15 DETA
Page 144 and 145:
16 SELECTING MODE3:OTHERSSETEDM OFF
Page 146 and 147:
16 SELECTING MODE7 Press [F3](OTHER
Page 148 and 149:
17.2 Checking the Optical Axis17 CH
Page 150 and 151:
17 CHECK AND ADJUSTMENT[Example]Low
Page 152 and 153:
17 CHECK AND ADJUSTMENTAbout30°Abo
Page 154 and 155:
17 CHECK AND ADJUSTMENT17.3.1Checki
Page 156 and 157:
17 CHECK AND ADJUSTMENT17.3.4Collim
Page 158 and 159:
17 CHECK AND ADJUSTMENT17.3.6Checki
Page 160 and 161:
17.4 How to Set the Instrument Cons
Page 162 and 163:
17 CHECK AND ADJUSTMENT14 Press the
Page 164 and 165:
19 SPECIAL ACCESSORIES19 SPECIAL AC
Page 166 and 167:
19 SPECIAL ACCESSORIESAluminum exte
Page 168 and 169:
21 PRISM SYSTEM21 PRISM SYSTEMArran
Page 170 and 171:
CIRCULARERRORPT# EXISTPT# DOESNOT E
Page 172 and 173:
23 SPECIFICATIONSAtmospheric Correc
Page 174 and 175:
APPENDIX1 Dual Axis CompensationInc
Page 176 and 177:
2 Precaution when Charging or Stori
Page 178:
EMC NOTICEIn industrial locations o
show all

GPT-3000 SERIES - FLT Geosystems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?