GPT-3000 SERIES - FLT Geosystems

More documents

Recommendations

Info

7 DATA COLLECTION7.1.2 Selecting a Coordinate File for Data CollectionWhen coordinate data in a coordinate data file are used for occupied point or backsight point, select acoordinate file from the data collect menu 2/2 beforehand.Operating procedure Operation DisplayDATA COLLECT 2/2F1:SELECT A FILEF2:PCODE INPUTF3:CONFIG. P↓1 Press the [F1](SELECT A FILE) key from DATACOLLECT menu 2/2.[F1]SELECT A FILEF1:MEAS.DATAF2:COORD.DATA2 Press the [F2](COORD.DATA) key. [F2]SELECT A FILEFN:INPUT LIST --- ENTER3 Select a coordinate file in the same manner asSection 7.1.1 “Selecting a File for Data Collection”.7.1.3 Occupied Point and Backsight PointThe occupied point and direction angle in the data collect mode are linked with the occupied point anddirection angle in normal coordinate measurement.It is possible to set or change the occupied point and direction angle from the data collect mode.Occupied point can be set by two setting methods as follow.1) Setting from the coordinate data stored in the internal memory.2) Direct key input.The following three setting methods for backsight point can be selected.1) Setting from the coordinate data stored in the internal memory.2) Direct key input of coordinate data.3) Direct key input of setting angle.Note: See 9.4 “Coordinate Data Direct Key Input” and 9.7.2 “Loading Data” for how to storecoordinate into the internal memory.●Example for setting the occupied point:In case of setting occupied point from the coordinate data stored in the internal memory.Operating procedure Operation Display1 Press the [F1](OCC.PT# INPUT) key from the [F1] PT# →PT-01data collect menu 1/2.ID :The previous data is shown.INS.HT: 0.000 mINPUT SRCH REC OCNEZ2 Press the [F4] (OCNEZ) key. [F4]OCC.PTPT#:PT-013 Press the [F1](INPUT) key and enter PT#.*1)Press the [F4](ENT) key.[F1]Enter PT#[F4]INPUT LIST NEZ ENTERN: 0.000mE: 0.000mZ: 0.000m>OK? [YES] [NO]7-4
7 DATA COLLECTION4 Press the [F3](YES) key. [F3]PT# →PT-11ID :INS.HT: 0.000 mINPUT SRCH REC OCNEZ5 Enter ID, INS.HT in the same way. *2),3)6 Press [F3](REC) key.7 Press [F3](YES) key.The display returns to the data collect menu 1/2.Enter ID,INS.HT[F3][F3]PT# :PT-11ID :INS.HT→ 1.335 mINPUT SRCH REC OCNEZ>REC ? [YES][NO]DATA COLLECT 1/2F1:OCC.PT# INPUTF2:BACKSIGHTF3:FS/SS P↓*1) Refer to Section 2.6 “How to Enter Alphanumeric characters”.*2) ID can be input by inputting a register number linked with PCODE Library.To show the list of PCODE library, press the [F2](SRCH) key.*3) Press the [F3](REC) key when you do not input the INS.HT.● The data recorded in data collect is PT#, ID and INS.HT.● If point is not found in internal memory "PT# DOES NOT EXIST" is displayed.7-5
Page 3 and 4:
FOREWORDThank you for purchasing th
Page 5 and 6:
Display for Safe UseIn order to enc
Page 7 and 8:
Laser Safety● Distance Measuremen
Page 10 and 11:
9.3.3 Deleting a File . . . . . . .
Page 12 and 13:
1 NOMENCLATURE AND FUNCTIONS1.1 Nom
Page 14 and 15:
1.2 Display●●●1 NOMENCLATURE
Page 16 and 17:
1.4 Function Key (Soft Key)1 NOMENC
Page 18 and 19:
1 NOMENCLATURE AND FUNCTIONS1.5 Sta
Page 20 and 21:
1 NOMENCLATURE AND FUNCTIONS●Tilt
Page 22 and 23:
2 PREPARATION FOR MEASUREMENT2.1 Po
Page 24 and 25:
2.3 Power Switch Key ON1 Confirm th
Page 26 and 27:
2.5 Vertical and Horizontal Angle T
Page 28 and 29:
2.6 How to Enter Alphanumeric chara
Page 30 and 31: 2 PREPARATION FOR MEASUREMENT2.8 La
Page 32 and 33: 3.2 Switching Horizontal Angle Righ
Page 34 and 35: 3.5 Repetition Angle Measurement3 A
Page 36 and 37: LOCK3.7 Compasses ( vertical angle)
Page 38 and 39: 4.3 Distance Measurement (Continuou
Page 40 and 41: 4 DISTANCE MEASUREMENT● Choose me
Page 42 and 43: 4.7 Offset Measurement4 DISTANCE ME
Page 44 and 45: 4 DISTANCE MEASUREMENTThe horizonta
Page 46 and 47: 4 DISTANCE MEASUREMENTAfter measuri
Page 48 and 49: 4 DISTANCE MEASUREMENT6 Measure the
Page 50 and 51: 4 DISTANCE MEASUREMENT6 Collimate t
Page 52 and 53: 5.2 Setting Height of the Instrumen
Page 54 and 55: 6 SPECIAL MODE (Menu Mode)By pressi
Page 56 and 57: 6 SPECIAL MODE (Menu Mode)Horizonta
Page 58 and 59: 6 SPECIAL MODE (Menu Mode)6.1.2 Mis
Page 60 and 61: 6 SPECIAL MODE (Menu Mode)The horiz
Page 62 and 63: 2) Z Coordinate Calculation from Kn
Page 64 and 65: 6 SPECIAL MODE (Menu Mode)6.1.4 Are
Page 66 and 67: 6 SPECIAL MODE (Menu Mode)When 3 or
Page 68 and 69: 6 SPECIAL MODE (Menu Mode)7 Collima
Page 70 and 71: 6 SPECIAL MODE (Menu Mode)3 Press t
Page 72 and 73: 6 SPECIAL MODE (Menu Mode)7 Press t
Page 74 and 75: 6 SPECIAL MODE (Menu Mode)6.4.5 Sel
Page 76 and 77: 6.5 Setting Contrast of DisplaySett
Page 78 and 79: 7 DATA COLLECTION●Data collect me
Page 82 and 83: 7 DATA COLLECTION●Example for set
Page 84 and 85: 7 DATA COLLECTION*1) Refer to Secti
Page 86 and 87: 7.3 Data Collect Offset Measurement
Page 88 and 89: 7 DATA COLLECTION7.3.2 Distance Off
Page 90 and 91: 7 DATA COLLECTION7.3.3 Plane Offset
Page 92 and 93: 7 DATA COLLECTION7.3.4 Column Offse
Page 94 and 95: 7.5 Point to Line MeasurementIn thi
Page 96 and 97: 7 DATA COLLECTION7.6 Editing PCODE
Page 98 and 99: 8 LAYOUTLAYOUT mode has two functio
Page 100 and 101: 8.1 Preparation8 LAYOUT8.1.1 Settin
Page 102 and 103: 8 LAYOUT8.1.3 Setting Occupied Poin
Page 104 and 105: 8 LAYOUT8.1.4 Setting Backsight Poi
Page 106 and 107: 8.2 Executing a LayoutThe following
Page 108 and 109: 8 LAYOUT8.2.1 Layout of Coordinates
Page 110 and 111: 8 LAYOUT6 Press the [F4](ENTER) key
Page 112 and 113: 8 LAYOUT5 Enter instrument height i
Page 114 and 115: ● Viewing PT# LIST8 LAYOUTYou can
Page 116 and 117: 9.1 Display Internal Memory StatusT
Page 118 and 119: ● To edit the data in searching m
Page 120 and 121: 9 MEMORY MANAGER MODE9.2.3 PCODE LI
Page 122 and 123: 9 MEMORY MANAGER MODE9.3.1 Rename a
Page 124 and 125: 9.4 Coordinate Data Direct Key Inpu
Page 126 and 127: 9.5 Delete a Coordinate Data from a
Page 128 and 129: 9.7 Data Communications9 MEMORY MAN
Page 130 and 131:
9 MEMORY MANAGER MODE9.7.3 Setting
Page 132 and 133:
10 SET AUDIO MODE10 SET AUDIO MODET
Page 134 and 135:
12 SETTING ATMOSPHERIC CORRECTION12
Page 136 and 137:
12 SETTING ATMOSPHERIC CORRECTIONAt
Page 138 and 139:
12-512 SETTING ATMOSPHERIC CORRECTI
Page 140 and 141:
14 POWER SOURCE AND CHARGING14.1 On
Page 142 and 143:
15 DETACH/ATTACH OF TRIBRACH15 DETA
Page 144 and 145:
16 SELECTING MODE3:OTHERSSETEDM OFF
Page 146 and 147:
16 SELECTING MODE7 Press [F3](OTHER
Page 148 and 149:
17.2 Checking the Optical Axis17 CH
Page 150 and 151:
17 CHECK AND ADJUSTMENT[Example]Low
Page 152 and 153:
17 CHECK AND ADJUSTMENTAbout30°Abo
Page 154 and 155:
17 CHECK AND ADJUSTMENT17.3.1Checki
Page 156 and 157:
17 CHECK AND ADJUSTMENT17.3.4Collim
Page 158 and 159:
17 CHECK AND ADJUSTMENT17.3.6Checki
Page 160 and 161:
17.4 How to Set the Instrument Cons
Page 162 and 163:
17 CHECK AND ADJUSTMENT14 Press the
Page 164 and 165:
19 SPECIAL ACCESSORIES19 SPECIAL AC
Page 166 and 167:
19 SPECIAL ACCESSORIESAluminum exte
Page 168 and 169:
21 PRISM SYSTEM21 PRISM SYSTEMArran
Page 170 and 171:
CIRCULARERRORPT# EXISTPT# DOESNOT E
Page 172 and 173:
23 SPECIFICATIONSAtmospheric Correc
Page 174 and 175:
APPENDIX1 Dual Axis CompensationInc
Page 176 and 177:
2 Precaution when Charging or Stori
Page 178:
EMC NOTICEIn industrial locations o
show all

GPT-3000 SERIES - FLT Geosystems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?