MAINTAINABILITY DESIGN TECHNIQUES METRIC - AcqNotes.com

More documents

Recommendations

Info

Downloaded from http://www.everyspec.com on 2011-10-29T14:56:01.DOD-HDBK-791(AM)4-5 SIZE OF ACCESSGenerally, one large access is better than two or moresmall ones; however, access openings must be sized for theequipment that will be maintained and for the actions thatwill be performed. This requires considerations of sight,type of tool required, light intensity, and required maintenanceoperations within the access—i.e., the maintainabilityengineer determines what the operator or technicianwill have to see and do before deciding on the accesssize. In some instances a small hole that admits a screwdriveror grease gun is sufficient access. In other instancesthe technician may have to get a hand or, perhaps, hiswhole body into a piece of equipment. Also, the frequencywith which the maintenance must be performed is a contributingfactor. Fig. 4-12 indicates that 70% of the maintenanceactions on electronic equipment are accomplishedby the use of a screwdriver, pliers, wrench, andsoldering iron. Obviously, the access opening for thisequipment should be large enough to permit the entranceand manipulation of these tools.Access size is also a function of the movementsturning, pulling, pushing, twisting—of the human bodypart or parts once access is gained and a function of thedimensions of the body part or parts that must be admittedthrough the opening. These two factors are determinedby dynamic and static body measurements. Humanfactors analyses also consider anthropometric sizing insystem functions. (See Chapter 9, “Human Factors”.) Thefact that the operator or technician maybe wearing arcticclothing while performing a maintenance action will alsoinfluence access size. Table 4-2 and Figs. 4-13, 4-14, and4-15 provide anthropometric data relative to gainingaccess through ports of various sizes.The size of access openings is also determined by thesize and shape of parts, components, or assemblies towhich access is desired. This is particularly true if the itemmust be removed and replaced through the openings.Access panels should be sized to avoid opening more thanone panel to gain access to any single item behind thepanel. The panel should be sized and componentslocated—to permit units to be removed along a straight orslightly curved path rather than a less direct path (Fig.4-5). This will facilitate removal and decrease the possibilityof damage to fragile components during withdrawal.4-6 EXAMPLESDesign for accessibility will be discussed for the followingseven areas:1. Electronics2. Fire control3. Missiles4. Mobile equipment trailers5. Tank-automotive materiel6. Army marine equipment7. Army aircraft.4-6.1 ELECTRONICSElectronic and electrical components should be locatedfor easy access and removal and should be designed ifnot of the throwaway type for case of access of testequipment and/or tools required for repair at the intermediateor depot level. Other accessibility decisions areinfluenced by considerations of equipment protection,operator or technician protection, layouts, openings,interference, vision. and handle design.Fig. 4-16 illustrates a foldout construction layout for-anelectronic chassis. This construction should be used forsubassemblies whenever feasible. l-he parts and wiringshould be positioned to prevent damage when opening orclosing the assembly.Braces or similar items should be provided to holdhinged assemblies in the “out” position while they arebeing maintained (Fig. 4-17); this arrangement leavesboth hands free to perform required rnaintenance operations.Rests or stands should be provided to presentdamage to delicate parts. If feasible, these rests or standsshould be part of the basic chassis as shown in Fig. 4-l8.Side aligning devices, similar to the ones shown in Fig.4-19, are desirable for heavy components because thecomponent can be slid into place.Some commonly used handles shown in Fig. 4-20are finger recess. hand recess. T-bar, and J-bar. Minimumacceptable dimensions of these handles together withminimum curvature or edges when carrying various loadsare also given. Handles should be provided on the coversof units and positioned for balance to facilitate removingthe cover and carrying the item; the use of fingers(Fig. 4-21) or levers to pry off covers is not good practice.Covers of cases should be designed to be lifted off the unit;the unit should not have to be lifted out of its cover(Figs.4-8(B) and 4-22). Handles can also serie various supplementaryapplications as shown in Fig. 4-23.Whenever practical, wire connections should be madewith U-type lugs rather than O-type lugs as shown in Fig.4-24 to facilitate removal. Termimals for soldered wireshould be far enough apart so that work on one terminaldoes not compromise the integrity of an adjacent terminalas shown in Fig. 4-25. The terminals should be longenough to prevent damage to insulation from the hotsoldering iron as shown in Fig. 4-26.Cables should be routed so they1. Are not pinched by doors, lids, and slides2. Are not walked on they should not be on thesame side of the panel reserved for access or operationsas shown in Fig. 4-273. Are accessible to the technician i.e., not underfloorboards, behind panels or components that are difficultto remove, or routed through congested areas4. Are not bent or unbent sharply, as shown in Fig.4-28, when connected or disconnected.Cable connections that are maintained between sta-4-10
Downloaded from http://www.everyspec.com on 2011-10-29T14:56:01.DOD-HDBK-791(AM)ScrewdriverPliersWrenchSoldering Gun/IronHammerFlashlightAlignment ToolSpin TightSocket setScrewholding ScrewdriverTube PullerSoldering AidTuning WandScrew StarterKnifeHeat DispenserRachetPunchWire StripperTweezer SFilePower DrillBurnishing ToolMirror StickBearing/Gear PullerWire StraightenerMechanical FingersScissorsChiselDrill pressCleaning BrushWire BrushFigure 4-12. Frequency With Which Hand Tools Are Used at Least Once in 427 MaintenanceTasks on Electronic Equipment4-11
Page 3 and 4:
Downloaded from http://www.everyspe
Page 6: Downloaded from http://www.everyspe
Page 9 and 10: Downloaded from http://www.everyspe
Page 55: Downloaded from http://www.everyspe
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
show all

MAINTAINABILITY DESIGN TECHNIQUES METRIC - AcqNotes.com

Create successful ePaper yourself

Delete template?

Save as template?