TO 1-1-700 - Robins Air Force Base

More documents

Recommendations

Info

TO 1-1-700 7.5.6.5.1 Grade 1 - A thick, hard, black CPC which can be removed with difficulty using mineral spirits or degreasing solvents. It offers the most corrosion protection of all the CPCs indoors and outdoors and may be used at temperatures down to 0 °F (-18 °C). If used at temperatures below 0 °F (-18 °C), the CPC film can crack and fall off leaving the surface unprotected. 7.5.6.5.2 Grade 2 - A thick, soft, grease-like, brown CPC that remains tacky and can be removed with mineral spirits or degreasing solvents. It protects under relatively severe conditions and given adequate maintenance touch-up as necessary, can be used for most maximum protection requirements. It may be used at temperatures down to -40 °F. It is not a good choice for parts that are handled frequently since it remains tacky. 7.5.6.5.3 Grade 3 - A thin, soft, oily film, water displacing CPC. This CPC doesn't penetrate into tight joints as well as MIL-PRF-81309, Type II or MIL-L-87177, Grade B, so one of them should be used as a substitute for this type of application. NOTE Remove the MIL-PRF-16173, Grade 3 film with A- A-59601, Type II or III, MIL-PRF-32295, Type II or MIL-PRF-680, Type II or III, or degreasing solvent prior to inspecting an area when the coating is dark and prevents visual inspection of the underlying surface for cracks. 7.5.6.5.4 Grade 4 - A thick, soft, waxy type CPC that dries to a tack free, semi-transparent film through which identification can be read. It provides good protection under relatively severe conditions when touched-up as necessary. It is excellent for use on in service equipment over MIL-PRF-81309, Type II, MIL-L-87177, Grade B, or MIL-PRF-16173, Grade 3 water displacing CPC since it dries to a tack free film. • If MIL-PRF-63460 is used in an area which will later be sealed or totally enclosed with no ventilation, allow at least 4 hours for the solvent to evaporate prior to sealing or closing off the area. Although MIL-PRF-63460 is a corrosion preventive compound, its solvent vapors may cause corrosion if not allowed to dissipate. • Do not use MIL-PRF-63460 on rubber or other elastomeric parts. MIL-PRF-63460 contains solvents which attack rubber "O" rings and other elastomeric parts. Do not use as a direct substitute for MIL-PRF-32033 (VV-L-800). • Do not use corrosion preventive compounds on the interior of fuel tanks or fuel cells, engines, or engine fuel systems as fouling of fuel systems may occur. • Do not use corrosion preventive compounds on engine parts or accessories which exceed 800 °F (427 °C). Corrosive reactions may occur with CPCs at high temperatures. • CPCs are not compatible with liquid oxygen and should not be used on oxygen equipment, lines, fittings, or storage bottles. Fire may result. 7.5.6.6 MIL-PRF-63460 Lubricant, Cleaner, and Preservative. MIL-PRF-63460 is a thin, water displacing, protective, penetrating lubricant used for cleaning, lubrication, and preservation of equipment hinges and fitting joints that experience only minor and infrequent relative motion. This material has good lubricating properties between -65 °F and +150 °F (-54 °C and +65 °C), and it is the best lubricant of all water displacing CPCs. It may be applied by brushing, dipping, or spraying by aerosol can or a pump sprayer. NOTE Use only CPCs authorized by and described in this manual and/or a system specific equipment manual. 7-20 Change 3
TO 1-1-700 Table 7-4. Corrosion Preventive Compounds Specification and Nomenclature Intended Use Type of Coating MIL-PRF-32033 Lubricating Oil, General Purpose, Preservative, (Water Displacing, Low Temperature); Military Symbol PL-S; NATO Code O-190 WATER-DISPLACING CPCs Lubrication and corrosion protection of hinges, other moving parts, small arms and automatic weapons, and wherever a low temperature, water displacing lubricant is required; requires frequent reapplications. Soft, oily coating and lubricant MIL-PRF-63460 Lubricant, Cleaner, and Preservative for Weapons and Weapons Systems; Military Symbol CLP; NATO Code S-758 MIL-PRF-16173 Corrosion Preventive Compound, Solvent Cutback, Cold Application, Grade 3 MIL-PRF-81309 Corrosion Preventive Compounds, Water Displacing, Ultra-thin Film Type II Type III MIL-L-87177 Lubricants, Corrosion Preventive, Water Displacing, Synthetic Grade B MIL-DTL-85054 Corrosion Preventive Compound, Water Displacing, Clear Lubrication and short term preservation of hinges, and small and large caliber weapons in all climatic conditions within a temperature range of -65 to +150 °F (-54 to +66 °C); facilitates the effective removal of firing residues, gums, and other contaminants from weapons components while providing adequate lubrication and short term preservation. Of all water displacing CPCs, this material is the best lubricant. Excellent water displacing characteristics and penetration into tight joints. Displacement of water; short term corrosion protection of metal surfaces during shipment, storage, and in service use; can be used on moving parts where minor lubrication is required, such as on hinges, bomb racks, and sliding parts. Displacement of water; short term corrosion protection of metal surfaces during shipment, storage, and in service use; corrosion protection of moving parts where very minor lubrication is required, such as hinge areas, bomb racks, and sliding parts. Cannot be used on interior of electrical or electronic equipment and connectors. Displacement of water; corrosion protection of electrical, avionics, and other electronic equipment, electrical connector plugs and contact pins. This material and MIL-L-87177, Grade B are the only CPCs that can be used on the interior of electrical or electronic equipment and connectors. Displacement of water, corrosion protection, and some lubrication on in service lightly loaded moving parts. Can be used on interior of electrical, avionics and other electronics equipment and connectors. Corrosion protection and water displacement for non-moving parts, such as skin seams, installed fastener heads where paint has cracked, access panel edges, and areas with damaged paint. Cannot be used on interior areas of electrical or electronics equipment and connectors or in joint areas of moving parts as it dries to a hard film. Thin corrosion preventive lubricant film Soft, oily, thin film (1.0 mil), light amber color Soft, oily, very thin film (0.5 mil) translucent, light amber color Soft, oily, ultra thin film (0.2 mil), translucent, light amber color. Soft, oily, thin film (0.5 mil), translucent, light amber color Dry, thin film (1.0 mil), transparent, colorless to slight blue tint Change 2 7-21
Page 1 and 2:
TO 1-1-700 TECHNICAL MANUAL CORROSI
Page 3 and 4:
TO 1-1-700 TABLE OF CONTENTS Chapte
Page 5 and 6:
TO 1-1-700 TABLE OF CONTENTS - CONT
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
TO 1-1-700 LIST OF ILLUSTRATIONS -
Page 15 and 16:
TO 1-1-700 FOREWORD 1. PURPOSE. The
Page 17 and 18:
TO 1-1-700 List of Related Publicat
Page 19 and 20:
TO 1-1-700 SAFETY SUMMARY 1. GENERA
Page 21 and 22:
TO 1-1-700 AMS-G-6032, GREASE, PLUG
Page 23 and 24:
TO 1-1-700 MIL-DTL-64159, COATING,
Page 25 and 26:
TO 1-1-700 MIL-PRF-27617, GREASE, A
Page 27 and 28:
TO 1-1-700 O-L-164, DRESSING, LEATH
Page 29:
TO 1-1-700 MIL-T-81772, THINNER, PO
Page 32 and 33:
TO 1-1-700 tronics equipment and th
Page 34 and 35:
TO 1-1-700 cleaning situation, syst
Page 36 and 37:
TO 1-1-700 c. Riveted joints shall
Page 38 and 39:
TO 1-1-700 c. Remove and replace an
Page 40 and 41:
TO 1-1-700 MIL-L-87177, LUBRICANT,
Page 42 and 43:
TO 1-1-700 Figure 3-1. Simplified C
Page 44 and 45:
TO 1-1-700 resistant, and also at t
Page 46 and 47:
TO 1-1-700 is first noticeable as a
Page 48 and 49:
TO 1-1-700 3.7.8 Oxygen Concentrati
Page 50 and 51:
TO 1-1-700 Figure 3-14. Concentrati
Page 52 and 53:
TO 1-1-700 Figure 3-17. Galvanic Se
Page 54 and 55:
TO 1-1-700 Figure 3-20. Aluminum Su
Page 56 and 57:
TO 1-1-700 3.8.7 CRES/Stainless Ste
Page 58 and 59: TO 1-1-700 3.9.10 Climate. Warm, mo
Page 60 and 61: TO 1-1-700 3.11 PREVENTATIVE MAINTE
Page 63 and 64: TO 1-1-700 CHAPTER 4 COMPOSITE AND
Page 65 and 66: TO 1-1-700 4.4.4.4 Glass parts shal
Page 67 and 68: TO 1-1-700 CHAPTER 5 PACKAGING (STO
Page 69 and 70: TO 1-1-700 extent of damage dependi
Page 71 and 72: TO 1-1-700 5.15 PRECAUTIONS FOR VCI
Page 73 and 74: TO 1-1-700 c. Secure the desiccant
Page 75 and 76: TO 1-1-700 Figure 5-8. Shock Isolat
Page 77 and 78: TO 1-1-700 Figure 5-9. Examples of
Page 79 and 80: TO 1-1-700 5.24.10 Rigid or Flexibl
Page 81 and 82: TO 1-1-700 CHAPTER 6 MOISTURE AND F
Page 83 and 84: TO 1-1-700 c. 6.2.6 Felt. Examine f
Page 85 and 86: TO 1-1-700 a. After first directing
Page 87: TO 1-1-700 6.4.5.14 Terminals, scre
Page 90 and 91: TO 1-1-700 NOTE • Authorized clea
Page 92 and 93: TO 1-1-700 Table 7-1. Cleaning of S
Page 102 and 103: TO 1-1-700 7.3.1.2.3 Portable, 45 g
Page 104 and 105: TO 1-1-700 Table 7-2. Common Milita
Page 106 and 107: TO 1-1-700 inactivity, storage, or
Page 110 and 111: TO 1-1-700 Table 7-4. Corrosion Pre
Page 112 and 113: TO 1-1-700 Table 7-5. Preservation
Page 114 and 115: TO 1-1-700 either case, MIL-PRF-269
Page 116 and 117: TO 1-1-700 MIL-PRF-85285, COATING,
Page 118 and 119: TO 1-1-700 c. Cadmium plated surfac
Page 120 and 121: TO 1-1-700 a. Scuff sand and feathe
Page 122 and 123: TO 1-1-700 7.7.7.2 If surface is no
Page 124 and 125: TO 1-1-700 7.7.9.2 Where only parti
Page 126 and 127: TO 1-1-700 7.8.1 Type I Application
Page 128 and 129: TO 1-1-700 Extend (Loctite) 32150 J
Page 130 and 131: TO 1-1-700 There are three ways to
Page 132 and 133: TO 1-1-700 vulnerable surfaces clea
Page 134 and 135: TO 1-1-700 Table 8-2. Materials, Th
Page 136 and 137: TO 1-1-700 Table 8-4. Electronic Cl
Page 150 and 151: TO 1-1-700 Table 8-5. Accessories o
Page 152 and 153: TO 1-1-700 Table 8-5. Accessories o
Page 154 and 155: TO 1-1-700 f. Devices with permanen
Page 156 and 157: TO 1-1-700 Table 8-7. Cleaning and
Page 158 and 159:
TO 1-1-700 MIL-PRF-87937, CLEANING
Page 160 and 161:
TO 1-1-700 of contamination). Maint
Page 162 and 163:
TO 1-1-700 8.8.2 Protective Coating
Page 164 and 165:
TO 1-1-700 • Tube clamps. • Min
Page 166 and 167:
TO 1-1-700 a. For bonding/grounding
Page 168 and 169:
TO 1-1-700 vertently destroy the mo
Page 170 and 171:
TO 1-1-700 doors, and other corrosi
Page 173 and 174:
TO 1-1-700 CHAPTER 10 CORROSION PRO
Page 175 and 176:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 177 and 178:
TO 1-1-700 d. After corrosion is re
Page 179 and 180:
TO 1-1-700 (3) Stainless/CRES steel
Page 181 and 182:
TO 1-1-700 10.9 WATER ENTRAPMENT AR
Page 183 and 184:
TO 1-1-700 f. Shield equipment from
Page 185 and 186:
TO 1-1-700 b. Use e-inch rivnuts of
Page 187 and 188:
TO 1-1-700 10.17.3 If the plating s
Page 189:
TO 1-1-700 Figure 10-16. Dissipatio
Page 192 and 193:
TO 1-1-700 (2) If allowable damage
Page 194 and 195:
TO 1-1-700 Table 11-1. Recommended
Page 196 and 197:
TO 1-1-700 11.6 3M CO. SCOTCH-BRITE
Page 198 and 199:
TO 1-1-700 11.11.2 Control of Mecha
Page 200 and 201:
TO 1-1-700 11.12.2 Mechanical Damag
Page 202 and 203:
TO 1-1-700 MIL-DTL-81706 (ALODINE),
Page 204 and 205:
TO 1-1-700 11.13.2.3 Application of
Page 206 and 207:
TO 1-1-700 only when there is no da
Page 208 and 209:
TO 1-1-700 NOTE SEMCO PASA-JELL 101
Page 210 and 211:
TO 1-1-700 (CRES), lead, ceramic, g
Page 212 and 213:
TO 1-1-700 11.13.7.2 Treatment of C
Page 214 and 215:
TO 1-1-700 MIL-A-46106, ADHESIVE/SE
Page 216 and 217:
TO 1-1-700 Table 12-1. Sealing Comp
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
TO 1-1-700 used to apply sealants i
Page 226 and 227:
TO 1-1-700 Figure 12-2. Sealant App
Page 228 and 229:
TO 1-1-700 Figure 12-4. Rivet Appli
Page 230 and 231:
TO 1-1-700 Figure 12-6. Sealant Inj
Page 232 and 233:
TO 1-1-700 below and adhere very po
Page 234 and 235:
TO 1-1-700 Table 12-2. Time Require
Page 236 and 237:
TO 1-1-700 Table 12-2. Time Require
Page 238 and 239:
TO 1-1-700 of 20 to 25 seconds in a
Page 240 and 241:
TO 1-1-700 d. Remove all uncured se
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
TO 1-1-700 Figure 12-12. Typical Me
Page 248 and 249:
TO 1-1-700 may be used for low temp
Page 250 and 251:
TO 1-1-700 Figure 12-14. Sealing Pr
show all

TO 1-1-700 - Robins Air Force Base

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?