TO 1-1-700 - Robins Air Force Base

More documents

Recommendations

Info

TO 1-1-700 tion of soap/detergent (any commercial dishwasher type) and water at a temperature of 100 °F (38 °C) to 140 °F (60 °C). Use of bleach is prohibited. Any residual dirt after this washing may be removed by scrubbing with a brush having medium stiffness bristles only. Rinse with clean water at a temperature between 75 °F (24 °C) and 100 °F (38 °C), and allow items to dry in open air. 6.2.3 Cork. Cork is notorious for absorbing moisture and causing crevice corrosion in faying surface areas. If at all possible, cork items should be replaced with like sized items fabricated from an appropriate type of closed cell rubber material. If this can not be done, the cork material shall at least be treated to make it fungus resistant. A-A-59282/A-A-53880, ALCOHOL, DENATURED ETHYL 54 A-A-59282/A-A-53880, ALCOHOL, DENATURED ETHYL 54 SALICYLANILIDE 63 DIHYDROXYDICHLORODIPHENYL METHANE 14 c. To provide fungus resistance, immerse canvas and/or duck in a 2% solution by volume of dihydroxydichlorodiphenyl methane in A-A-59282/A-A-53880, Type III denatured ethyl alcohol until all bubbling ceases; remove the item from the solution; allow it to dry in open air. d. To provide moisture repellency, immerse the item that has already been treated for fungus resistance in an aqueous solution of Aridex L mixed per the manufacture's instructions, and allow it to remain in solution until thoroughly impregnated. Allow items to drain at room temperature and dry with hot air at a temperature not exceeding 250 °F (121 °C). NOTE • Dihydroxydichlorodiphenylmethane fungus repellent may be procured commercially from the Sindar Corp; New York, NY. • Aridex L moisture repellent may be procured commercially from the Aridex Co; New York, NY. • O-E 760, Type III denatured ethyl alcohol is available through the Air Force supply system in a 1 gallon can under NSN 6810-00-543-7415. • To prevent shrinkage, a drying frame may be used on canvas cases during these procedures. 6.2.3.1 To provide fungus resistance for cork items, immerse them in a 2% solution by volume of salicylanilide in A-A- 59282/A-A-53880, Type III denatured ethyl alcohol until all bubbling ceases; allow them to dry in open air. 6.2.4 Paper. Paper hermetically sealed within parts or bonded between sheets of plastic material need not be treated. ASTM D 3955 (MIL-V-173), VANISH, ELECTRICAL INSULATING 12 a. Brush or spray mounted paper labels and approximately 1/2 inch of mounting surface immediately adjacent to the label edges with ASTM D 3955 (MIL-V-173) electrical insulating (moisture and fungus resistant) varnish. b. SALICYLANILIDE 63 A-A-59282/A-A-53880, ALCOHOL, DENATURED ETHYL 54 b. Immerse unmounted paper charts, diagrams, speakers, cones, etc. in a 2% solution by volume of salicylanilide in A-A-59282/A-A-53880, Type III denatured ethyl alcohol; allow them to dry in open air. 6-2 Change 4
TO 1-1-700 c. 6.2.6 Felt. Examine felt for wear, torn seams, stains, fungi, etc. Felt items considered to be still serviceable will be processed as follows: ASTM D 3955 (MIL-V-173), VANISH, ELECTRICAL INSULATING 12 c. Spray or brush decalcomanias used on interior surfaces with ASTM D 3955 (MIL-V-173) electrical insulating (moisture and fungus resistant) varnish. NOTE ASTM D 3955 (MIL-V-173) electrical insulating (moisture and fungus resistant) varnish is available through the Air Force supply system in a 16 oz. aerosol can under NSN 5970-00-832-6950 and in a 1 gallon can under NSN 5970-00-285-0269. 6.2.5 Webbing. Examine webbing. a. Wash items in a washing machine or other device in which webbing items are tumbled in a solution of soap/ detergent (any commercial dishwasher type) and water at a temperature of 100 °F (38 °C) to 140 °F (60 °C). Use of bleach is prohibited. Any residual dirt after this washing may be removed by scrubbing with a brush having medium stiffness bristles only. Rinse with clean water at a temperature between 75 °F (24 °C) and 100 °F (38 °C), and allow items to dry in open air. DIHYDROXYDICHLORODIPHENYL METHANE 14 A-A-59282/A-A-53880, ALCOHOL, DENATURED ETHYL 54 O-E-760, ALCOHOL, DENATURED ETHYL 54 SALICYLANILIDE 63 NOTE The foregoing treatment may be eliminated if it can be ascertained that felt was properly treated prior to procurement. a. To provide fungus resistance for felt items, immerse them in a 2% solution by volume of salicylanilide and denatured ethyl alcohol until bubbling ceases. b. Remove excess solution by squeezing felt items through a wringer such as an electric or hand operated household washing machine wringer or equivalent. c. Dry the felt items in open air. 6.2.7 Treatment of Metal Parts. Metal parts on any of the leather, canvas or duck, cork, paper, webbing, or felt items shall be cleaned after treatments specified above have been applied. The cleaning procedures are as follows: A-A-59282/A-A-53880, ALCOHOL, DENATURED ETHYL 54 TT-I-735, ALCOHOL, ISOPROPYL 65 TT-N-95, NAPHTHA, ALIPHATIC 66 Re-dyeing or painting webbing with enamels is prohibited as this can damage the webbing. b. To provide fungus resistance, immerse webbing in a 2% solution by volume of dihydroxydichlorodiphenyl methane in A-A-59282/A-A-53880, Type III denatured ethyl alcohol until all bubbling ceases; remove the item from the solution; allow it to dry in open air. a. Clean any oil, grease, or residual treatment from the metal parts by wiping with a soft cloth wet with a 50/50 by volume mixture of TT-N-95 aliphatic naphtha and TT-I-735 isopropyl alcohol, and dry them by wiping with a clean, dry cloth. b. Surface of metal parts shall be finished to meet requirements stated in the equipment system specific mainte- Change 4 6-3
Page 1 and 2:
TO 1-1-700 TECHNICAL MANUAL CORROSI
Page 3 and 4:
TO 1-1-700 TABLE OF CONTENTS Chapte
Page 5 and 6:
TO 1-1-700 TABLE OF CONTENTS - CONT
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
TO 1-1-700 LIST OF ILLUSTRATIONS -
Page 15 and 16:
TO 1-1-700 FOREWORD 1. PURPOSE. The
Page 17 and 18:
TO 1-1-700 List of Related Publicat
Page 19 and 20:
TO 1-1-700 SAFETY SUMMARY 1. GENERA
Page 21 and 22:
TO 1-1-700 AMS-G-6032, GREASE, PLUG
Page 23 and 24:
TO 1-1-700 MIL-DTL-64159, COATING,
Page 25 and 26:
TO 1-1-700 MIL-PRF-27617, GREASE, A
Page 27 and 28:
TO 1-1-700 O-L-164, DRESSING, LEATH
Page 29:
TO 1-1-700 MIL-T-81772, THINNER, PO
Page 32 and 33: TO 1-1-700 tronics equipment and th
Page 34 and 35: TO 1-1-700 cleaning situation, syst
Page 36 and 37: TO 1-1-700 c. Riveted joints shall
Page 38 and 39: TO 1-1-700 c. Remove and replace an
Page 40 and 41: TO 1-1-700 MIL-L-87177, LUBRICANT,
Page 42 and 43: TO 1-1-700 Figure 3-1. Simplified C
Page 44 and 45: TO 1-1-700 resistant, and also at t
Page 46 and 47: TO 1-1-700 is first noticeable as a
Page 48 and 49: TO 1-1-700 3.7.8 Oxygen Concentrati
Page 50 and 51: TO 1-1-700 Figure 3-14. Concentrati
Page 52 and 53: TO 1-1-700 Figure 3-17. Galvanic Se
Page 54 and 55: TO 1-1-700 Figure 3-20. Aluminum Su
Page 56 and 57: TO 1-1-700 3.8.7 CRES/Stainless Ste
Page 58 and 59: TO 1-1-700 3.9.10 Climate. Warm, mo
Page 60 and 61: TO 1-1-700 3.11 PREVENTATIVE MAINTE
Page 63 and 64: TO 1-1-700 CHAPTER 4 COMPOSITE AND
Page 65 and 66: TO 1-1-700 4.4.4.4 Glass parts shal
Page 67 and 68: TO 1-1-700 CHAPTER 5 PACKAGING (STO
Page 69 and 70: TO 1-1-700 extent of damage dependi
Page 71 and 72: TO 1-1-700 5.15 PRECAUTIONS FOR VCI
Page 73 and 74: TO 1-1-700 c. Secure the desiccant
Page 75 and 76: TO 1-1-700 Figure 5-8. Shock Isolat
Page 77 and 78: TO 1-1-700 Figure 5-9. Examples of
Page 79 and 80: TO 1-1-700 5.24.10 Rigid or Flexibl
Page 81: TO 1-1-700 CHAPTER 6 MOISTURE AND F
Page 85 and 86: TO 1-1-700 a. After first directing
Page 87: TO 1-1-700 6.4.5.14 Terminals, scre
Page 90 and 91: TO 1-1-700 NOTE • Authorized clea
Page 92 and 93: TO 1-1-700 Table 7-1. Cleaning of S
Page 102 and 103: TO 1-1-700 7.3.1.2.3 Portable, 45 g
Page 104 and 105: TO 1-1-700 Table 7-2. Common Milita
Page 106 and 107: TO 1-1-700 inactivity, storage, or
Page 108 and 109: TO 1-1-700 7.5.6.5.1 Grade 1 - A th
Page 110 and 111: TO 1-1-700 Table 7-4. Corrosion Pre
Page 112 and 113: TO 1-1-700 Table 7-5. Preservation
Page 114 and 115: TO 1-1-700 either case, MIL-PRF-269
Page 116 and 117: TO 1-1-700 MIL-PRF-85285, COATING,
Page 118 and 119: TO 1-1-700 c. Cadmium plated surfac
Page 120 and 121: TO 1-1-700 a. Scuff sand and feathe
Page 122 and 123: TO 1-1-700 7.7.7.2 If surface is no
Page 124 and 125: TO 1-1-700 7.7.9.2 Where only parti
Page 126 and 127: TO 1-1-700 7.8.1 Type I Application
Page 128 and 129: TO 1-1-700 Extend (Loctite) 32150 J
Page 130 and 131: TO 1-1-700 There are three ways to
Page 132 and 133:
TO 1-1-700 vulnerable surfaces clea
Page 134 and 135:
TO 1-1-700 Table 8-2. Materials, Th
Page 136 and 137:
TO 1-1-700 Table 8-4. Electronic Cl
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
TO 1-1-700 Table 8-5. Accessories o
Page 152 and 153:
TO 1-1-700 Table 8-5. Accessories o
Page 154 and 155:
TO 1-1-700 f. Devices with permanen
Page 156 and 157:
TO 1-1-700 Table 8-7. Cleaning and
Page 158 and 159:
TO 1-1-700 MIL-PRF-87937, CLEANING
Page 160 and 161:
TO 1-1-700 of contamination). Maint
Page 162 and 163:
TO 1-1-700 8.8.2 Protective Coating
Page 164 and 165:
TO 1-1-700 • Tube clamps. • Min
Page 166 and 167:
TO 1-1-700 a. For bonding/grounding
Page 168 and 169:
TO 1-1-700 vertently destroy the mo
Page 170 and 171:
TO 1-1-700 doors, and other corrosi
Page 173 and 174:
TO 1-1-700 CHAPTER 10 CORROSION PRO
Page 175 and 176:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 177 and 178:
TO 1-1-700 d. After corrosion is re
Page 179 and 180:
TO 1-1-700 (3) Stainless/CRES steel
Page 181 and 182:
TO 1-1-700 10.9 WATER ENTRAPMENT AR
Page 183 and 184:
TO 1-1-700 f. Shield equipment from
Page 185 and 186:
TO 1-1-700 b. Use e-inch rivnuts of
Page 187 and 188:
TO 1-1-700 10.17.3 If the plating s
Page 189:
TO 1-1-700 Figure 10-16. Dissipatio
Page 192 and 193:
TO 1-1-700 (2) If allowable damage
Page 194 and 195:
TO 1-1-700 Table 11-1. Recommended
Page 196 and 197:
TO 1-1-700 11.6 3M CO. SCOTCH-BRITE
Page 198 and 199:
TO 1-1-700 11.11.2 Control of Mecha
Page 200 and 201:
TO 1-1-700 11.12.2 Mechanical Damag
Page 202 and 203:
TO 1-1-700 MIL-DTL-81706 (ALODINE),
Page 204 and 205:
TO 1-1-700 11.13.2.3 Application of
Page 206 and 207:
TO 1-1-700 only when there is no da
Page 208 and 209:
TO 1-1-700 NOTE SEMCO PASA-JELL 101
Page 210 and 211:
TO 1-1-700 (CRES), lead, ceramic, g
Page 212 and 213:
TO 1-1-700 11.13.7.2 Treatment of C
Page 214 and 215:
TO 1-1-700 MIL-A-46106, ADHESIVE/SE
Page 216 and 217:
TO 1-1-700 Table 12-1. Sealing Comp
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
TO 1-1-700 used to apply sealants i
Page 226 and 227:
TO 1-1-700 Figure 12-2. Sealant App
Page 228 and 229:
TO 1-1-700 Figure 12-4. Rivet Appli
Page 230 and 231:
TO 1-1-700 Figure 12-6. Sealant Inj
Page 232 and 233:
TO 1-1-700 below and adhere very po
Page 234 and 235:
TO 1-1-700 Table 12-2. Time Require
Page 236 and 237:
TO 1-1-700 Table 12-2. Time Require
Page 238 and 239:
TO 1-1-700 of 20 to 25 seconds in a
Page 240 and 241:
TO 1-1-700 d. Remove all uncured se
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
TO 1-1-700 Figure 12-12. Typical Me
Page 248 and 249:
TO 1-1-700 may be used for low temp
Page 250 and 251:
TO 1-1-700 Figure 12-14. Sealing Pr
show all

TO 1-1-700 - Robins Air Force Base

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?