TO 1-1-700 - Robins Air Force Base

More documents

Recommendations

Info

TO 1-1-700 c. Cadmium plated surfaces shall receive either a Type II supplementary chromate treatment or a Type III supplementary phosphate treatment per SAE-AMS-QQ-P-416 (QQ-P-416) using procedures in TO 42C2-1-7. Bleached or clear chromate treatment of is not permissible. MIL-PRF-85285, COATING POLYURETHANE, HIGH SOLIDS 50 NOTE For DEPOT LEVEL maintenance, touch-up of small areas of zinc and/or cadmium plating may be accomplished by brush plating per MIL-STD-8651 using procedures in TO 42C2-1-7 in lieu of complete stripping and replating. MIL-PRF-23377, TYPE I & II, PRIMER, EPOXY CHEMICAL AND SOLVENT RESISTANT 38 MIL-PRF-85582, PRIMER, EPOXY, WATERBORNE 69 MIL-DTL-53022, PRIMER, EPOXY, CORROSION INHIBITING, LEAD AND CHROMATE FREE 34 MIL-P-53030, PRIMER, EPOXY, WATER REDUCIBLE, LEAD, CHROME FREE 35 d. Prime the plated surfaces with one coat of MIL-PRF- 23377, Type I, Class C or MIL-PRF-85582, Type I, Class C2 epoxy primers to a DFT of 0.6 to 0.9 mils (0.0006 to 0.0009 inch) or MIL-DTL-53022 or MIL-P- 53030 epoxy primers to a DFT of 0.9 to 1.1 mils (0.0009 to 0.0011 inch); as applicable from the equipment system specific technical data. Application shall be per procedures in Chapters 4, 5, and 6 of TO 1-1-8. MIL-DTL-64159, COATING, POLYURETHANE, CHEMICAL RESISTANT, WATERBORNE 24 e. Apply two coats of either MIL-PRF-85285 standard polyurethane coating or MIL-DTL-64159 waterborne CARC polyurethane coating to a DFT of 1.8 to 3.2 mils (0.0018 to 0.0032 inch) over the primer per procedures in Chapters 4, 5, and 6 of TO 1-1-8. The color and gloss shall match the existing coating system as specified in equipment system specific technical data or as otherwise directed by the equipment SPM. 7.7.4.3 If surface is not exposed to view in its normal operating condition, except while under repair, use the same procedures specified in paragraph 7.7.4.2 step a, step b., and step c., the NOTE under step c. and step d. Application of a topcoat per paragraph 7.7.4.2 step e is not required. 7.7.4.4 Where only partial refinishing (touch-up) is required for a few small scratches, nicks, or spots where corrosion was removed on painted surfaces, the following procedure shall be used: a. Scuff sand and feather out painted edges and all corroded or scratched surfaces to be refinished per maintenance painting and touch-up procedures in Chapter 5 of TO 1-1-8. b. Clean the entire surface to be touched-up of all dust, dirt, oil, and grease by solvent wiping per procedures in Chapter 3 of TO 1-1-8 prior to priming. Apply one coat of the same primers specified in paragraph 7.7.4.2 step d to all surfaces to be touched-up (both those exposed and unexposed to direct view in normal operating conditions) using maintenance painting and touch-up procedures in Chapter 5 of TO 1-1-8. c. If surfaces are exposed to direct view in normal operating conditions, apply one coat of the same topcoats specified in paragraph 7.7.4.2 step e over the primer using maintenance painting and touch-up procedures in Chapter 5 of TO 1-1-8. 7-30 Change 4
TO 1-1-700 MIL-DTL-81706 (ALODINE), COATING, CHEMICAL CONVERSION 23 MIL-DTL-53022, PRIMER, EPOXY, CORROSION INHIBITING, LEAD AND CHROMATE FREE 34 NOTE The initial chromate surface treatment is required on these surfaces and may be applied by using MIL- DTL-81706, Class 1A, Form VI, Method D Touch-N- Prep (TNP) pens per procedures in Section II of Chapter 5 in TO 1-1-691. 7.7.5 Tin on Ferrous Base Metal. When complete refinishing is required due to extensive corrosion or loss of film adhesion, disassemble the equipment and/or structure as far as practical and remove the defective paint system per procedures in Chapter 2 of TO 1-1-8. 7.7.5.1 . If surface, when reassembled in its normal operating condition will be exposed to direct view, the following procedures will be used: a. For DEPOT LEVEL maintenance only, strip old plating from equipment or part to the base metal per procedures in TO 42C2-1-7. For FIELD LEVEL maintenance and when it is impractical to strip the plating due to size, shape, or connection to other parts, lightly sand areas where corrosion is noted to remove corrosion products of the plating as well as the base metal per procedures in Chapter 5 of TO 1-1-691. b. For DEPOT LEVEL maintenance, reapply tin plating by the hot dip method per ASTM B-339, Grade A to a minimum thickness of 0.5 mils (0.0005 inch) or by electroplating per ASTM B-545 to a minimum thickness of 0.3 mils (0.0003 inch) using procedures in TO 42C2-1- 7, and treat the plated surface with the metal conditioner described in paragraph 7.8 of this manual. MIL-PRF-23377, TYPE I & II, PRIMER, EPOXY CHEMICAL AND SOLVENT RESISTANT 38 MIL-PRF-85582, PRIMER, EPOXY, WATERBORNE 69 MIL-P-53030, PRIMER, EPOXY, WATER REDUCIBLE, LEAD, CHROME FREE 35 c. Prime the plated surfaces with one coat of MIL-PRF- 23377, Type I, Class C or MIL-PRF-85582, Type I, Class C2 epoxy primers to a DFT of 0.6 to 0.9 mils (0.0006 to 0.0009 inch) or MIL-DTL-53022 or MIL-P- 53030 epoxy primers to a DFT of 0.9 to 1.1 mils (0.0009 to 0.0011 inch), as applicable, from the equipment system specific technical data. Application shall be per procedures in Chapters 4, 5, and 6 of TO 1-1-8. MIL-PRF-85285, COATING POLYURETHANE, HIGH SOLIDS 50 MIL-DTL-64159, COATING, POLYURETHANE, CHEMICAL RESISTANT, WATERBORNE 24 d. Apply two coats of either MIL-PRF-85285 standard polyurethane coating or MIL-DTL-64159 waterborne CARC polyurethane coating to a DFT of 1.8 to 3.2 mils (0.0018 to 0.0032 inch) over the primer per procedures in Chapters 4, 5, and 6 of TO 1-1-8. The color and gloss shall match the existing coating system as specified in equipment system specific technical data or as otherwise directed by the equipment SPM. 7.7.5.2 . If the surface is not exposed to view in its normal operating condition, except while under repair, no further finish over plated surfaces will be required. However, plating thickness shall be a minimum of 0.5 mils (0.0005 inch) for hot dip and 0.3 mils (0.0003 inch) for electroplate. 7.7.5.3 . Where only partial refinishing (touch-up) is required for a few small scratches, nicks, or spots where corrosion was removed on painted surfaces, the following procedure shall be used: Change 4 7-31
Page 1 and 2:
TO 1-1-700 TECHNICAL MANUAL CORROSI
Page 3 and 4:
TO 1-1-700 TABLE OF CONTENTS Chapte
Page 5 and 6:
TO 1-1-700 TABLE OF CONTENTS - CONT
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
TO 1-1-700 LIST OF ILLUSTRATIONS -
Page 15 and 16:
TO 1-1-700 FOREWORD 1. PURPOSE. The
Page 17 and 18:
TO 1-1-700 List of Related Publicat
Page 19 and 20:
TO 1-1-700 SAFETY SUMMARY 1. GENERA
Page 21 and 22:
TO 1-1-700 AMS-G-6032, GREASE, PLUG
Page 23 and 24:
TO 1-1-700 MIL-DTL-64159, COATING,
Page 25 and 26:
TO 1-1-700 MIL-PRF-27617, GREASE, A
Page 27 and 28:
TO 1-1-700 O-L-164, DRESSING, LEATH
Page 29:
TO 1-1-700 MIL-T-81772, THINNER, PO
Page 32 and 33:
TO 1-1-700 tronics equipment and th
Page 34 and 35:
TO 1-1-700 cleaning situation, syst
Page 36 and 37:
TO 1-1-700 c. Riveted joints shall
Page 38 and 39:
TO 1-1-700 c. Remove and replace an
Page 40 and 41:
TO 1-1-700 MIL-L-87177, LUBRICANT,
Page 42 and 43:
TO 1-1-700 Figure 3-1. Simplified C
Page 44 and 45:
TO 1-1-700 resistant, and also at t
Page 46 and 47:
TO 1-1-700 is first noticeable as a
Page 48 and 49:
TO 1-1-700 3.7.8 Oxygen Concentrati
Page 50 and 51:
TO 1-1-700 Figure 3-14. Concentrati
Page 52 and 53:
TO 1-1-700 Figure 3-17. Galvanic Se
Page 54 and 55:
TO 1-1-700 Figure 3-20. Aluminum Su
Page 56 and 57:
TO 1-1-700 3.8.7 CRES/Stainless Ste
Page 58 and 59:
TO 1-1-700 3.9.10 Climate. Warm, mo
Page 60 and 61:
TO 1-1-700 3.11 PREVENTATIVE MAINTE
Page 63 and 64:
TO 1-1-700 CHAPTER 4 COMPOSITE AND
Page 65 and 66:
TO 1-1-700 4.4.4.4 Glass parts shal
Page 67 and 68: TO 1-1-700 CHAPTER 5 PACKAGING (STO
Page 69 and 70: TO 1-1-700 extent of damage dependi
Page 71 and 72: TO 1-1-700 5.15 PRECAUTIONS FOR VCI
Page 73 and 74: TO 1-1-700 c. Secure the desiccant
Page 75 and 76: TO 1-1-700 Figure 5-8. Shock Isolat
Page 77 and 78: TO 1-1-700 Figure 5-9. Examples of
Page 79 and 80: TO 1-1-700 5.24.10 Rigid or Flexibl
Page 81 and 82: TO 1-1-700 CHAPTER 6 MOISTURE AND F
Page 83 and 84: TO 1-1-700 c. 6.2.6 Felt. Examine f
Page 85 and 86: TO 1-1-700 a. After first directing
Page 87: TO 1-1-700 6.4.5.14 Terminals, scre
Page 90 and 91: TO 1-1-700 NOTE • Authorized clea
Page 92 and 93: TO 1-1-700 Table 7-1. Cleaning of S
Page 102 and 103: TO 1-1-700 7.3.1.2.3 Portable, 45 g
Page 104 and 105: TO 1-1-700 Table 7-2. Common Milita
Page 106 and 107: TO 1-1-700 inactivity, storage, or
Page 108 and 109: TO 1-1-700 7.5.6.5.1 Grade 1 - A th
Page 110 and 111: TO 1-1-700 Table 7-4. Corrosion Pre
Page 112 and 113: TO 1-1-700 Table 7-5. Preservation
Page 114 and 115: TO 1-1-700 either case, MIL-PRF-269
Page 116 and 117: TO 1-1-700 MIL-PRF-85285, COATING,
Page 120 and 121: TO 1-1-700 a. Scuff sand and feathe
Page 122 and 123: TO 1-1-700 7.7.7.2 If surface is no
Page 124 and 125: TO 1-1-700 7.7.9.2 Where only parti
Page 126 and 127: TO 1-1-700 7.8.1 Type I Application
Page 128 and 129: TO 1-1-700 Extend (Loctite) 32150 J
Page 130 and 131: TO 1-1-700 There are three ways to
Page 132 and 133: TO 1-1-700 vulnerable surfaces clea
Page 134 and 135: TO 1-1-700 Table 8-2. Materials, Th
Page 136 and 137: TO 1-1-700 Table 8-4. Electronic Cl
Page 150 and 151: TO 1-1-700 Table 8-5. Accessories o
Page 152 and 153: TO 1-1-700 Table 8-5. Accessories o
Page 154 and 155: TO 1-1-700 f. Devices with permanen
Page 156 and 157: TO 1-1-700 Table 8-7. Cleaning and
Page 158 and 159: TO 1-1-700 MIL-PRF-87937, CLEANING
Page 160 and 161: TO 1-1-700 of contamination). Maint
Page 162 and 163: TO 1-1-700 8.8.2 Protective Coating
Page 164 and 165: TO 1-1-700 • Tube clamps. • Min
Page 166 and 167: TO 1-1-700 a. For bonding/grounding
Page 168 and 169:
TO 1-1-700 vertently destroy the mo
Page 170 and 171:
TO 1-1-700 doors, and other corrosi
Page 173 and 174:
TO 1-1-700 CHAPTER 10 CORROSION PRO
Page 175 and 176:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 177 and 178:
TO 1-1-700 d. After corrosion is re
Page 179 and 180:
TO 1-1-700 (3) Stainless/CRES steel
Page 181 and 182:
TO 1-1-700 10.9 WATER ENTRAPMENT AR
Page 183 and 184:
TO 1-1-700 f. Shield equipment from
Page 185 and 186:
TO 1-1-700 b. Use e-inch rivnuts of
Page 187 and 188:
TO 1-1-700 10.17.3 If the plating s
Page 189:
TO 1-1-700 Figure 10-16. Dissipatio
Page 192 and 193:
TO 1-1-700 (2) If allowable damage
Page 194 and 195:
TO 1-1-700 Table 11-1. Recommended
Page 196 and 197:
TO 1-1-700 11.6 3M CO. SCOTCH-BRITE
Page 198 and 199:
TO 1-1-700 11.11.2 Control of Mecha
Page 200 and 201:
TO 1-1-700 11.12.2 Mechanical Damag
Page 202 and 203:
TO 1-1-700 MIL-DTL-81706 (ALODINE),
Page 204 and 205:
TO 1-1-700 11.13.2.3 Application of
Page 206 and 207:
TO 1-1-700 only when there is no da
Page 208 and 209:
TO 1-1-700 NOTE SEMCO PASA-JELL 101
Page 210 and 211:
TO 1-1-700 (CRES), lead, ceramic, g
Page 212 and 213:
TO 1-1-700 11.13.7.2 Treatment of C
Page 214 and 215:
TO 1-1-700 MIL-A-46106, ADHESIVE/SE
Page 216 and 217:
TO 1-1-700 Table 12-1. Sealing Comp
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
TO 1-1-700 used to apply sealants i
Page 226 and 227:
TO 1-1-700 Figure 12-2. Sealant App
Page 228 and 229:
TO 1-1-700 Figure 12-4. Rivet Appli
Page 230 and 231:
TO 1-1-700 Figure 12-6. Sealant Inj
Page 232 and 233:
TO 1-1-700 below and adhere very po
Page 234 and 235:
TO 1-1-700 Table 12-2. Time Require
Page 236 and 237:
TO 1-1-700 Table 12-2. Time Require
Page 238 and 239:
TO 1-1-700 of 20 to 25 seconds in a
Page 240 and 241:
TO 1-1-700 d. Remove all uncured se
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
TO 1-1-700 Figure 12-12. Typical Me
Page 248 and 249:
TO 1-1-700 may be used for low temp
Page 250 and 251:
TO 1-1-700 Figure 12-14. Sealing Pr
show all

TO 1-1-700 - Robins Air Force Base

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?