TO 1-1-700 - Robins Air Force Base

More documents

Recommendations

Info

TO 1-1-700 A-A-3007, THINNER, PHENOLFORMALDEDYDE AND MEDIUM OIL AND STYRENATED ALKYD PAINTS AND VARNISHES 1 A-A-3007, Thinner, is extremely flammable and a skin, eye and respiratory tract irritant. Use only in a well ventilated area. Impervious gloves, chemical goggles and impervious footwear are required. Do not take internally. Avoid contact with skin and eyes. Avoid breathing vapor and/or mist. Isolate from oxidizers, heat, sparks, electric equipment and open flame. Do not apply to hot surfaces without taking special precautions. A-A-59199, CLEANING COMPOUND, OPTICAL LENS 5 A-A-59199, Optical Lens Cleaning Compound, is flammable and a skin, eye and respiratory tract irritant. Ingestion can cause blindness and death. Use only in a well ventilated area. Neoprene, nitrile or rubber gloves, safety goggles and protective apron are required. Wash thoroughly after handling and before eating, drinking or smoking. Store in a clean, cool well ventilated area away from ignition sources. A-A-55827, CHROMIUM TRIOXIDE 2 A-A-55827, Chromium Trioxide, is highly toxic to the eyes, skin and respiratory tract. Chemical splash proof goggles and/ or face shield, chemical resistant rubber gloves and apron are required. Good general ventilation is usually adequate. Do not inhale dust. Reacts vigorously or violently with a range of organic materials. A-A-59260 (MIL-C-14460, TYPE I), CORROSION REMOVING COMPOUND 6 A-A-59260 (MIL-C-14460, Type I), Corrosion/Rust Removing Compound, is a sodium hydroxide solution and therefore, highly alkaline. It is toxic to skin, eyes and respiratory tract. Chemical splash proof goggles and/or face shields and chemical resistant rubber gloves and aprons are required. Heated dip tanks shall be properly ventilated, and ventilation shall be evaluated by the Bioenvironmental Engineer prior to their initial use. When preparing/mixing this highly alkaline solution, never pour water onto the sodium hydroxide granules or flakes; this will generate an excessive amount of heat. Always pour the sodium hydroxide granules/flakes into the water. A-A-55828 (O-S-809), SULFURIC ACID SOLUTIONS 3 A-A-55828 (O-S-809), Sulfuric Acid Solutions, are toxic to the skin, eyes, and respiratory tract. Use only in well ventilated areas. Chemical, splash proof goggles and/or face shields and chemical resistant rubber gloves and aprons are required. Highly reactive. Prevent accidental contact with water. Never add water to corrosive. Always add corrosives to water. Store in cool, dry, well ventilated location. A-A-59282, ACID, BORIC 7 A-A-59282, Boric Acid, is a skin, eye and respiratory tract irritant. Avoid contact with skin and eyes. Do not breathe dust or take internally. Dust mask, protective gloves, and splash proof or dust resistant goggles are required. Wash thoroughly after handling. Use only in a well ventilated area. Keep away from heat and open flames. A-A-59105 (O-N-350), NITRIC ACID 4 A-A-59105 (O-N-350), Nitric Acid, is highly toxic and a strong oxidizer. Do not get on skin, eyes, or clothing. Do not breathe vapors or mist. Use only in well ventilated areas. Wash hands thoroughly after handling. Never pour water into acid, as excessive heat will be generated. Always pour the acid into the water. Do not store near combustible materials. AMS-G-4343, GREASE, AIRCRAFT 8 AMS-G-4343, Aircraft Grease, is a skin and eye irritant. Do not take internally. Avoid skin and eye contact. Wash hands after each use. Use only in a well ventilated area. Rubber or plastic gloves and safety glasses are recommended. Store in a clean, cool well ventilated area away from ignition sources. xviii Change 1
TO 1-1-700 AMS-G-6032, GREASE, PLUG VALVE 9 AMS-G-6032, Plug Valve Grease, is an eye irritant. Wash hands after use. Avoid contact with eyes. Use safety glasses as a minimum. Do not heat to above 300 °F/149 °C to prevent formulation of toxic vapors. ASTM D 928, SODIUM BICARBONATE 13 ASTM D 928, Sodium Bicarbonate, is an eye irritant. Avoid contact with eyes. Safety glasses/goggles are required. Store in a clean, cool well ventilated area. from heat and open flames. AMS-S-83318, SEALING COMPOUND, LOW TEMPERA- TURE CURING 10 AMS-S-83318, Low Temperature Curing Sealing Compound, is a skin, eye and respiratory tract irritant. Avoid repeated or prolonged contact with the skin. Use in well ventilated areas only. Nitrile or rubber gloves and chemical resistant goggles are required. To prevent ingestion, always wash your hands before eating or smoking. Store in cool, dry, well ventilated area away from heat, ignition sources and direct sunlight. DIHYDROXYDICHLORODIPHENYL METHANE 14 Dihydroxydichlorodiphenyl methane is an eye, skin, and respiratory tract irritant. Not to be swallowed. Moderately toxic. Use only in a well ventilated area. Chemical gloves and splash proof safety goggles are required. Keep away from heat and open flames. Store in a clean, cool well ventilated area away from ignition sources. MIL-DTL-25681, LUBRICANT, MOLYBDENUM DISULFIDE SILICONE 15 ASTM D 329 (PART NO. O-A-51), ACETONE 11 ASTM D 329 (part No. O-A-51), Acetone, is a flammable low order oral toxin and is a skin, eye and respiratory tract irritant. Do not take internally. Use only in a well ventilated area. Rubber, vinyl or other imperious gloves and splash proof goggles are required. Keep away from heat and open flames. Store in a clean, cool well ventilated area. MIL-DTL-25681, Molybdenum Disulfide Silicone Lubricant, is an eye, skin, and respiratory tract irritant. Avoid breathing vapors, and skin and eye contact. Rubber gloves and safety goggles are required. Wash hands thoroughly after handling. Use only in well ventilated areas. DOD-P-15328, PRIMER, PRETREATMENT (WASH) FOR METALS 16 ASTM D 3955 (MIL-V-173), VANISH, ELECTRICAL INSULATING 12 ASTM D 3955 (MIL-V-173), Electrical Insulating Vanish, is a skin, eye and respiratory tract irritant. Do not take internally. Rubber gloves, safety goggles, coverall or long sleeves are required. Wash hands with soap and water after handling. Use only in a well ventilated area. Keep away from heat and open flames. Store in a clean, cool well ventilated area. DOD-P-15328, Pretreatment (Wash) Primer, is flammable and a skin, eye, and respiratory tract irritant. Avoid breathing vapors. Use only in well ventilated areas. Rubber gloves and safety glasses with side shields are required. Wear face shield when spraying. Avoid excessive heat and sources of ignition. Change 4 xix
Page 1 and 2: TO 1-1-700 TECHNICAL MANUAL CORROSI
Page 3 and 4: TO 1-1-700 TABLE OF CONTENTS Chapte
Page 5 and 6: TO 1-1-700 TABLE OF CONTENTS - CONT
Page 13 and 14: TO 1-1-700 LIST OF ILLUSTRATIONS -
Page 15 and 16: TO 1-1-700 FOREWORD 1. PURPOSE. The
Page 17 and 18: TO 1-1-700 List of Related Publicat
Page 19: TO 1-1-700 SAFETY SUMMARY 1. GENERA
Page 23 and 24: TO 1-1-700 MIL-DTL-64159, COATING,
Page 25 and 26: TO 1-1-700 MIL-PRF-27617, GREASE, A
Page 27 and 28: TO 1-1-700 O-L-164, DRESSING, LEATH
Page 29: TO 1-1-700 MIL-T-81772, THINNER, PO
Page 32 and 33: TO 1-1-700 tronics equipment and th
Page 34 and 35: TO 1-1-700 cleaning situation, syst
Page 36 and 37: TO 1-1-700 c. Riveted joints shall
Page 38 and 39: TO 1-1-700 c. Remove and replace an
Page 40 and 41: TO 1-1-700 MIL-L-87177, LUBRICANT,
Page 42 and 43: TO 1-1-700 Figure 3-1. Simplified C
Page 44 and 45: TO 1-1-700 resistant, and also at t
Page 46 and 47: TO 1-1-700 is first noticeable as a
Page 48 and 49: TO 1-1-700 3.7.8 Oxygen Concentrati
Page 50 and 51: TO 1-1-700 Figure 3-14. Concentrati
Page 52 and 53: TO 1-1-700 Figure 3-17. Galvanic Se
Page 54 and 55: TO 1-1-700 Figure 3-20. Aluminum Su
Page 56 and 57: TO 1-1-700 3.8.7 CRES/Stainless Ste
Page 58 and 59: TO 1-1-700 3.9.10 Climate. Warm, mo
Page 60 and 61: TO 1-1-700 3.11 PREVENTATIVE MAINTE
Page 63 and 64: TO 1-1-700 CHAPTER 4 COMPOSITE AND
Page 65 and 66: TO 1-1-700 4.4.4.4 Glass parts shal
Page 67 and 68: TO 1-1-700 CHAPTER 5 PACKAGING (STO
Page 69 and 70: TO 1-1-700 extent of damage dependi
Page 71 and 72:
TO 1-1-700 5.15 PRECAUTIONS FOR VCI
Page 73 and 74:
TO 1-1-700 c. Secure the desiccant
Page 75 and 76:
TO 1-1-700 Figure 5-8. Shock Isolat
Page 77 and 78:
TO 1-1-700 Figure 5-9. Examples of
Page 79 and 80:
TO 1-1-700 5.24.10 Rigid or Flexibl
Page 81 and 82:
TO 1-1-700 CHAPTER 6 MOISTURE AND F
Page 83 and 84:
TO 1-1-700 c. 6.2.6 Felt. Examine f
Page 85 and 86:
TO 1-1-700 a. After first directing
Page 87:
TO 1-1-700 6.4.5.14 Terminals, scre
Page 90 and 91:
TO 1-1-700 NOTE • Authorized clea
Page 92 and 93:
TO 1-1-700 Table 7-1. Cleaning of S
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
TO 1-1-700 7.3.1.2.3 Portable, 45 g
Page 104 and 105:
TO 1-1-700 Table 7-2. Common Milita
Page 106 and 107:
TO 1-1-700 inactivity, storage, or
Page 108 and 109:
TO 1-1-700 7.5.6.5.1 Grade 1 - A th
Page 110 and 111:
TO 1-1-700 Table 7-4. Corrosion Pre
Page 112 and 113:
TO 1-1-700 Table 7-5. Preservation
Page 114 and 115:
TO 1-1-700 either case, MIL-PRF-269
Page 116 and 117:
TO 1-1-700 MIL-PRF-85285, COATING,
Page 118 and 119:
TO 1-1-700 c. Cadmium plated surfac
Page 120 and 121:
TO 1-1-700 a. Scuff sand and feathe
Page 122 and 123:
TO 1-1-700 7.7.7.2 If surface is no
Page 124 and 125:
TO 1-1-700 7.7.9.2 Where only parti
Page 126 and 127:
TO 1-1-700 7.8.1 Type I Application
Page 128 and 129:
TO 1-1-700 Extend (Loctite) 32150 J
Page 130 and 131:
TO 1-1-700 There are three ways to
Page 132 and 133:
TO 1-1-700 vulnerable surfaces clea
Page 134 and 135:
TO 1-1-700 Table 8-2. Materials, Th
Page 136 and 137:
TO 1-1-700 Table 8-4. Electronic Cl
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
TO 1-1-700 Table 8-5. Accessories o
Page 152 and 153:
TO 1-1-700 Table 8-5. Accessories o
Page 154 and 155:
TO 1-1-700 f. Devices with permanen
Page 156 and 157:
TO 1-1-700 Table 8-7. Cleaning and
Page 158 and 159:
TO 1-1-700 MIL-PRF-87937, CLEANING
Page 160 and 161:
TO 1-1-700 of contamination). Maint
Page 162 and 163:
TO 1-1-700 8.8.2 Protective Coating
Page 164 and 165:
TO 1-1-700 • Tube clamps. • Min
Page 166 and 167:
TO 1-1-700 a. For bonding/grounding
Page 168 and 169:
TO 1-1-700 vertently destroy the mo
Page 170 and 171:
TO 1-1-700 doors, and other corrosi
Page 173 and 174:
TO 1-1-700 CHAPTER 10 CORROSION PRO
Page 175 and 176:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 177 and 178:
TO 1-1-700 d. After corrosion is re
Page 179 and 180:
TO 1-1-700 (3) Stainless/CRES steel
Page 181 and 182:
TO 1-1-700 10.9 WATER ENTRAPMENT AR
Page 183 and 184:
TO 1-1-700 f. Shield equipment from
Page 185 and 186:
TO 1-1-700 b. Use e-inch rivnuts of
Page 187 and 188:
TO 1-1-700 10.17.3 If the plating s
Page 189:
TO 1-1-700 Figure 10-16. Dissipatio
Page 192 and 193:
TO 1-1-700 (2) If allowable damage
Page 194 and 195:
TO 1-1-700 Table 11-1. Recommended
Page 196 and 197:
TO 1-1-700 11.6 3M CO. SCOTCH-BRITE
Page 198 and 199:
TO 1-1-700 11.11.2 Control of Mecha
Page 200 and 201:
TO 1-1-700 11.12.2 Mechanical Damag
Page 202 and 203:
TO 1-1-700 MIL-DTL-81706 (ALODINE),
Page 204 and 205:
TO 1-1-700 11.13.2.3 Application of
Page 206 and 207:
TO 1-1-700 only when there is no da
Page 208 and 209:
TO 1-1-700 NOTE SEMCO PASA-JELL 101
Page 210 and 211:
TO 1-1-700 (CRES), lead, ceramic, g
Page 212 and 213:
TO 1-1-700 11.13.7.2 Treatment of C
Page 214 and 215:
TO 1-1-700 MIL-A-46106, ADHESIVE/SE
Page 216 and 217:
TO 1-1-700 Table 12-1. Sealing Comp
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
TO 1-1-700 used to apply sealants i
Page 226 and 227:
TO 1-1-700 Figure 12-2. Sealant App
Page 228 and 229:
TO 1-1-700 Figure 12-4. Rivet Appli
Page 230 and 231:
TO 1-1-700 Figure 12-6. Sealant Inj
Page 232 and 233:
TO 1-1-700 below and adhere very po
Page 234 and 235:
TO 1-1-700 Table 12-2. Time Require
Page 236 and 237:
TO 1-1-700 Table 12-2. Time Require
Page 238 and 239:
TO 1-1-700 of 20 to 25 seconds in a
Page 240 and 241:
TO 1-1-700 d. Remove all uncured se
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
TO 1-1-700 Figure 12-12. Typical Me
Page 248 and 249:
TO 1-1-700 may be used for low temp
Page 250 and 251:
TO 1-1-700 Figure 12-14. Sealing Pr
show all

TO 1-1-700 - Robins Air Force Base

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?