TO 1-1-700 - Robins Air Force Base

More documents

Recommendations

Info

TO 1-1-700 with a thin film of MIL-DTL-85054, Type IA or IIA, Clear Water Displacing Corrosion Preventive Compound, and allow it to cure. MIL-PRF-32033, LUBRICATING OIL, GENERAL PUR- POSE, PRESERVATIVE (WATER-DISPLACING, LOW TEMPERATURE) 41 MIL-PRF-680 AND A-A-59601, SOLVENT, DEGREASING, TYPE II AND III 45 a. Clean affected areas with CCC-C-46, Class 7 cleaning cloth dampened with MIL-PRF-680, MIL-PRF-32295, Type II, or A-A-59601, Type II Degreasing/Dry Cleaning Solvent, or other cleaner as specified by systemspecific manuals or the equipment SPM. b. Remove corrosion with A-A-58054, Type I, Grade A or B Abrasive Mat, or 320 grit abrasive cloth, as appropriate. MIL-PRF-63460, LUBRICANT, CLEANER AND PRESER- VATIVE 44 TT-I-735, ALCOHOL, ISOPROPYL 65 c. Wipe residue with CCC-C-46, Class 7 cleaning cloth dampened with TT-I-735 Isopropyl Alcohol and allow to dry. Do not use MIL-PRF-63460 corrosion preventive compound, or MIL-PRF-32033 lubricating oil/general purpose preservative, around oxygen or oxygen fittings since fire/explosion may result. f. Either in conjunction with corrosion removal or as a standalone procedure, periodic lubrication of access and/or entry door, panel, and vent hinges and door latches will be accomplished as directed by maintenance inspection and at 6 month intervals by applying either MIL-PRF-32033 or MIL-PRF-63460 water displacing lubricant/preservative/corrosion preventive compound (CPC) to the hinge node joints, hinge pins, and all moving parts of latches. For hinges, this can be done with the hinges assembled, but it is better to remove the hinge pins during lubrication and reinstall them after wards. During extreme weather or in harsh environments, increase the lubrication interval. Apply a generous quantity of either MIL-L-63460 (preferably) or MIL-PRF-32033 water displacing, corrosion preventive compound (CPC), actuate hinges and latches several times to make sure that the CPCs and lubricants penetrate all crevices thoroughly, and then wipe off excess from exterior surfaces. d. After corrosion is removed from metal surfaces treat them as follows: MIL-DTL-81706 (ALODINE), COATING, CHEMICAL CONVERSION 23 Exercise care when using MIL-DTL-81706, Class 1A Chemical Conversion Coating Material, near electronic hardware. It can cause corrosion of delicate electronic devices if not suitably protected. (1) Treat aluminum surfaces with MIL-DTL-81706, Class 1A Chemical Conversion Coating Material, using procedures in Chapter 7 of this manual. 10.7.2 Equipment Hinges and Latches. If corrosion is found, treat as follows: MIL-C-10578, COMPOUND, CORROSION REMOVING AND METAL CONDITIONING 20 MIL-PRF-32295, TYPE II, CLEANER, NON-AQUEOUS, LOW-VOC, HAP-FREE (2) Treat carbon steel (other than stainless steel/CRES) surfaces with MIL-C-10578, Type VI Brush-On Phosphoric Acid Base Corrosion Removing and Metal Conditioning Compound per procedures in Chapter 7 of this manual. 10-6 Change 3
TO 1-1-700 (3) Stainless/CRES steel requires no further treatment. MIL-DTL-85054, COMPOUND, CORROSION PREVEN- TIVE 25 MIL-PRF-32033, LUBRICATING OIL, GENERAL PURPOSE, PRESERVATIVE (WATER-DISPLACING, LOW TEMPERATURE) 41 Do not apply MIL-DTL-85054 to functional areas of hinges and latches as this material dries to a hard film and will cause them to bind and/or seize up. e. Prepare bare metal non-moving parts requiring no lubrication for touch-up painting as specified in TOs 1-1-691 and 1-1-8. When environmental conditions or time do not permit, preserve surfaces requiring no lubrication with a thin film of MIL-DTL-85054, Type IA or IIA, Clear, Water Displacing, Corrosion Preventive Compound, and allow it to cure. MIL-PRF-81309, LUBRICANT, CORROSION PREVEN- TIVE COMPOUND 46 Do not use MIL-PRF-81309, MIL-DTL-85054, MIL- DTL-63460, and MIL-PRF-16173 corrosion preventive compounds, or MIL-PRF-32033 lubricating oil/ general purpose preservative, around oxygen or oxygen fittings since fire/explosion may result. f. Either in conjunction with corrosion removal or as a stand alone procedure, periodic lubrication of access door or case closure panel hinges and latches (see Figure 10-8) will be accomplished as directed by maintenance inspection and at 6 month intervals with either MIL-PRF-81309, Type II or III or MIL-L-87177, Class B Water-Displacing, CPC applied either by brush or spray. Apply a generous quantity of either MIL-PRF- 81309, Type II or III or MIL-L-87177, Class B water displacing CPC, actuate hinges and latches several times to make sure that the CPCs and lubricants penetrate all crevices thoroughly, and then wipe off excess from exterior surfaces. MIL-L-87177, LUBRICANT, CORROSION PREVENTIVE COMPOUND, WATER DISPLACING 32 MIL-DTL-85054, COMPOUND, CORROSION PREVENTIVE 25 MIL-PRF-63460, LUBRICANT, CLEANER AND PRESER- VATIVE 44 Figure 10-8. Electronic Shelter Door MIL-PRF-16173, COMPOUND, CORROSION PREVEN- TIVE 37 Change 2 10-7
Page 1 and 2:
TO 1-1-700 TECHNICAL MANUAL CORROSI
Page 3 and 4:
TO 1-1-700 TABLE OF CONTENTS Chapte
Page 5 and 6:
TO 1-1-700 TABLE OF CONTENTS - CONT
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
TO 1-1-700 LIST OF ILLUSTRATIONS -
Page 15 and 16:
TO 1-1-700 FOREWORD 1. PURPOSE. The
Page 17 and 18:
TO 1-1-700 List of Related Publicat
Page 19 and 20:
TO 1-1-700 SAFETY SUMMARY 1. GENERA
Page 21 and 22:
TO 1-1-700 AMS-G-6032, GREASE, PLUG
Page 23 and 24:
TO 1-1-700 MIL-DTL-64159, COATING,
Page 25 and 26:
TO 1-1-700 MIL-PRF-27617, GREASE, A
Page 27 and 28:
TO 1-1-700 O-L-164, DRESSING, LEATH
Page 29:
TO 1-1-700 MIL-T-81772, THINNER, PO
Page 32 and 33:
TO 1-1-700 tronics equipment and th
Page 34 and 35:
TO 1-1-700 cleaning situation, syst
Page 36 and 37:
TO 1-1-700 c. Riveted joints shall
Page 38 and 39:
TO 1-1-700 c. Remove and replace an
Page 40 and 41:
TO 1-1-700 MIL-L-87177, LUBRICANT,
Page 42 and 43:
TO 1-1-700 Figure 3-1. Simplified C
Page 44 and 45:
TO 1-1-700 resistant, and also at t
Page 46 and 47:
TO 1-1-700 is first noticeable as a
Page 48 and 49:
TO 1-1-700 3.7.8 Oxygen Concentrati
Page 50 and 51:
TO 1-1-700 Figure 3-14. Concentrati
Page 52 and 53:
TO 1-1-700 Figure 3-17. Galvanic Se
Page 54 and 55:
TO 1-1-700 Figure 3-20. Aluminum Su
Page 56 and 57:
TO 1-1-700 3.8.7 CRES/Stainless Ste
Page 58 and 59:
TO 1-1-700 3.9.10 Climate. Warm, mo
Page 60 and 61:
TO 1-1-700 3.11 PREVENTATIVE MAINTE
Page 63 and 64:
TO 1-1-700 CHAPTER 4 COMPOSITE AND
Page 65 and 66:
TO 1-1-700 4.4.4.4 Glass parts shal
Page 67 and 68:
TO 1-1-700 CHAPTER 5 PACKAGING (STO
Page 69 and 70:
TO 1-1-700 extent of damage dependi
Page 71 and 72:
TO 1-1-700 5.15 PRECAUTIONS FOR VCI
Page 73 and 74:
TO 1-1-700 c. Secure the desiccant
Page 75 and 76:
TO 1-1-700 Figure 5-8. Shock Isolat
Page 77 and 78:
TO 1-1-700 Figure 5-9. Examples of
Page 79 and 80:
TO 1-1-700 5.24.10 Rigid or Flexibl
Page 81 and 82:
TO 1-1-700 CHAPTER 6 MOISTURE AND F
Page 83 and 84:
TO 1-1-700 c. 6.2.6 Felt. Examine f
Page 85 and 86:
TO 1-1-700 a. After first directing
Page 87:
TO 1-1-700 6.4.5.14 Terminals, scre
Page 90 and 91:
TO 1-1-700 NOTE • Authorized clea
Page 92 and 93:
TO 1-1-700 Table 7-1. Cleaning of S
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
TO 1-1-700 7.3.1.2.3 Portable, 45 g
Page 104 and 105:
TO 1-1-700 Table 7-2. Common Milita
Page 106 and 107:
TO 1-1-700 inactivity, storage, or
Page 108 and 109:
TO 1-1-700 7.5.6.5.1 Grade 1 - A th
Page 110 and 111:
TO 1-1-700 Table 7-4. Corrosion Pre
Page 112 and 113:
TO 1-1-700 Table 7-5. Preservation
Page 114 and 115:
TO 1-1-700 either case, MIL-PRF-269
Page 116 and 117:
TO 1-1-700 MIL-PRF-85285, COATING,
Page 118 and 119:
TO 1-1-700 c. Cadmium plated surfac
Page 120 and 121:
TO 1-1-700 a. Scuff sand and feathe
Page 122 and 123:
TO 1-1-700 7.7.7.2 If surface is no
Page 124 and 125:
TO 1-1-700 7.7.9.2 Where only parti
Page 126 and 127:
TO 1-1-700 7.8.1 Type I Application
Page 128 and 129: TO 1-1-700 Extend (Loctite) 32150 J
Page 130 and 131: TO 1-1-700 There are three ways to
Page 132 and 133: TO 1-1-700 vulnerable surfaces clea
Page 134 and 135: TO 1-1-700 Table 8-2. Materials, Th
Page 136 and 137: TO 1-1-700 Table 8-4. Electronic Cl
Page 150 and 151: TO 1-1-700 Table 8-5. Accessories o
Page 152 and 153: TO 1-1-700 Table 8-5. Accessories o
Page 154 and 155: TO 1-1-700 f. Devices with permanen
Page 156 and 157: TO 1-1-700 Table 8-7. Cleaning and
Page 158 and 159: TO 1-1-700 MIL-PRF-87937, CLEANING
Page 160 and 161: TO 1-1-700 of contamination). Maint
Page 162 and 163: TO 1-1-700 8.8.2 Protective Coating
Page 164 and 165: TO 1-1-700 • Tube clamps. • Min
Page 166 and 167: TO 1-1-700 a. For bonding/grounding
Page 168 and 169: TO 1-1-700 vertently destroy the mo
Page 170 and 171: TO 1-1-700 doors, and other corrosi
Page 173 and 174: TO 1-1-700 CHAPTER 10 CORROSION PRO
Page 175 and 176: TO 1-1-700 MIL-PRF-81733, SEALING A
Page 177: TO 1-1-700 d. After corrosion is re
Page 181 and 182: TO 1-1-700 10.9 WATER ENTRAPMENT AR
Page 183 and 184: TO 1-1-700 f. Shield equipment from
Page 185 and 186: TO 1-1-700 b. Use e-inch rivnuts of
Page 187 and 188: TO 1-1-700 10.17.3 If the plating s
Page 189: TO 1-1-700 Figure 10-16. Dissipatio
Page 192 and 193: TO 1-1-700 (2) If allowable damage
Page 194 and 195: TO 1-1-700 Table 11-1. Recommended
Page 196 and 197: TO 1-1-700 11.6 3M CO. SCOTCH-BRITE
Page 198 and 199: TO 1-1-700 11.11.2 Control of Mecha
Page 200 and 201: TO 1-1-700 11.12.2 Mechanical Damag
Page 202 and 203: TO 1-1-700 MIL-DTL-81706 (ALODINE),
Page 204 and 205: TO 1-1-700 11.13.2.3 Application of
Page 206 and 207: TO 1-1-700 only when there is no da
Page 208 and 209: TO 1-1-700 NOTE SEMCO PASA-JELL 101
Page 210 and 211: TO 1-1-700 (CRES), lead, ceramic, g
Page 212 and 213: TO 1-1-700 11.13.7.2 Treatment of C
Page 214 and 215: TO 1-1-700 MIL-A-46106, ADHESIVE/SE
Page 216 and 217: TO 1-1-700 Table 12-1. Sealing Comp
Page 224 and 225: TO 1-1-700 used to apply sealants i
Page 226 and 227: TO 1-1-700 Figure 12-2. Sealant App
Page 228 and 229:
TO 1-1-700 Figure 12-4. Rivet Appli
Page 230 and 231:
TO 1-1-700 Figure 12-6. Sealant Inj
Page 232 and 233:
TO 1-1-700 below and adhere very po
Page 234 and 235:
TO 1-1-700 Table 12-2. Time Require
Page 236 and 237:
TO 1-1-700 Table 12-2. Time Require
Page 238 and 239:
TO 1-1-700 of 20 to 25 seconds in a
Page 240 and 241:
TO 1-1-700 d. Remove all uncured se
Page 242 and 243:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 244 and 245:
TO 1-1-700 MIL-PRF-81733, SEALING A
Page 246 and 247:
TO 1-1-700 Figure 12-12. Typical Me
Page 248 and 249:
TO 1-1-700 may be used for low temp
Page 250 and 251:
TO 1-1-700 Figure 12-14. Sealing Pr
show all

TO 1-1-700 - Robins Air Force Base

Create successful ePaper yourself

Delete template?

Save as template?