HQ Pro-Stitcher User Manual - Handi Quilter

More documents

Recommendations

Info

6. The black cables attached to the HQ Pro-Stitcher carriage should be routed up between the rear handles and the quilting machine, toward the right-hand side of the machine (looking at the machine from the back). Place the black cable clips (Page 3, J) as shown in Figures 15a, b and c, and route the cable accordingly. Figure 15 b Figure 15 c Figure 15 a Page 10 HQ Pro-Stitcher User Manual
7. The small black cable with the black 3-connector clip should be routed underneath the P-Pod (Figure 16) and snapped into the quilting machine’s “Y” encoder (Figure 17). The two black cables that run from the carriage up to the computer should be clipped into the cable clip under the rear handlebar as shown in Figure 16 to help prevent these cables from getting caught on the edges of the carriage. 8. Verify that the Y-axis gear engages the blue rack for the Y-axis. a. To do this, look from the back of the machine, between the bottom of the quilting machine and the top of the carriage. If the white gear is not high enough to engage the blue rack above it (Page 3, H), adjust the lever on the side of the carriage closest to the back of the carriage (the Y-axis disengagement lever) into the lowest position (the teeth of the gear and the teeth of the rack should engage). b. If horizontal adjustment is needed to ensure that at least half the white gear and blue rack are interlocking, loosen the two screws that mount the Y-axis bracket to the base plates and push the bracket in the direction necessary while re-tightening the screws. 9. With the power cable unplugged and both engagement levers in the down position, ensure that as the quilting machine is moved in both the X and the Y directions, the corresponding gears are rotating as well. Figure 16 Figure 17 www.HandiQuilter.com/ProStitcher Page 11
Page 1: HQ Pro-Stitcher ® The future of Qu
Page 4 and 5: Tutorials, Upgrades and What’s Ne
Page 6 and 7: Installation HQ 24 Fusion HQ 18 Ava
Page 8 and 9: Y-Rack Installation 1. Carefully la
Page 10 and 11: Setting up the New Carriage 1. With
Page 14 and 15: Computer/Touch Screen Monitor Assem
Page 16 and 17: 6. Remove the computer from its pac
Page 18 and 19: HQ Pro-Stitcher Parts List for HQ S
Page 20 and 21: X-Rack Installation 1. Make sure th
Page 22 and 23: Y-Rack Installation 1. Carefully la
Page 24 and 25: The HQ Pro-Stitcher is an upgrade t
Page 26 and 27: Setting Up the New Carriage 1. Remo
Page 28 and 29: 7. Carefully lift the quilting mach
Page 30 and 31: Computer/Touch Screen Monitor Assem
Page 32 and 33: 7. Remove the computer from its pac
Page 34 and 35: Getting Started Setting up the HQ P
Page 36 and 37: HQ Pro-Stitcher Step-by-Step Instru
Page 38 and 39: Step 2: Viewing the Pattern and Mov
Page 40 and 41: Step 3: Setup Menu By pressing the
Page 42 and 43: Step 4: Manipulating the Pattern Qu
Page 44 and 45: 1. Enter the value of the desired p
Page 46 and 47: identify two points by which to cre
Page 48 and 49: What if the First Crop was Wrong?
Page 50 and 51: 3. If the patterns should be overla
Page 52 and 53: 1. • Determine Determine the area
Page 54 and 55: Step 5: Positioning the Pattern Aft
Page 56 and 57: Step 6: Quilting the Pattern Save t
Page 58 and 59: Start Quilting Press the “Start Q
Page 60 and 61: Auto Turned Off If the “Auto” b
Page 62 and 63:
Press the right arrow from within t
Page 64 and 65:
If the “Auto Find” option box i
Page 66 and 67:
Reset Current Resume Postion After
Page 68 and 69:
Clean System The “Clean System”
Page 70 and 71:
1. The line at the top center of th
Page 72 and 73:
Folder Options Folder Options (Pres
Page 74 and 75:
Manual/Channel This screen is inten
Page 76 and 77:
Pause Record When finished, or if t
Page 78 and 79:
HQ Pro-Stitcher Advanced Features A
Page 80 and 81:
HQ Pro-Stitcher Advanced Features (
Page 82 and 83:
0BHQ ProStitcher Troubleshootin
Page 84 and 85:
the Design Library ‣ The current
Page 86 and 87:
Procedure for Calibrating the Touch
Page 88 and 89:
Warranty Warranty issues should, wh
Page 90 and 91:
Warranty Claims Service under the a
Page 92 and 93:
This page was intentionally left bl
Page 94 and 95:
This page was intentionally left bl
Page 97:
Designed by a Quilter, for Quilters
show all

HQ Pro-Stitcher User Manual - Handi Quilter

Create successful ePaper yourself

Delete template?

Save as template?