TO LORD
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
So<br />
you need some advice?<br />
Our plan<br />
will straighten<br />
you out!<br />
For you, we've got a plan. A comfort and visibility. Best of all, you<br />
seating plan. Done just for your get your plan without obligation. So,<br />
theatre. Single use, or multiple use. you've got an eight-sided hall with a<br />
New place going up, or old .m Uy/lm Cwinn rev °l vin K stage in the middle<br />
one getting new chairs. A ^^L m of a swimming pool? Tell us<br />
comprehensive plan designed I wOOpaity about it. We promise not to<br />
to give you maximum capac- I po. box 2429 laugh. For your free plan,<br />
.. j " , Grand Rapids, ...<br />
lty.andyourpatronsmaximum 1=f Michisan 49501 lust write.<br />
Projection and Sound—<br />
by the<br />
Continued from page h\<br />
manufacturer. For such adjusting, i<br />
is necessary to loosen the socket head scre\<br />
and lo adjust the belt tightener until propc<br />
tightness is obtained. The running of th<br />
toothed belt may be slightly impaired b<br />
the belt tightener.<br />
Note: Belt tension must by no means<br />
be tightened to a point where the rubber<br />
bearing of the motor is not shifted<br />
and that the toothed belt does not come<br />
off the synchroflex wheel of the motor.<br />
The tension of the toothed belt for th<br />
magnetic sound unit is also adjusted with<br />
belt tightener. Make sure this belt also is ac<br />
justed to<br />
the proper tension.<br />
V-Belt<br />
Adjustment<br />
The mounted V-belt should have a littl<br />
play. Adjustments have to be made by shif<br />
ing the tapered disc on the idling gear bea<br />
ing. First remove the V-belt and the tapere<br />
disc of the idling gear bearing. If the tei<br />
sion is too low, remove the washers betwee<br />
the two tapered discs so that the V-belt<br />
further tightened. On the other hand, if th<br />
tension is too high, put more washers b<<br />
tween the two tapered discs. Such adjus<br />
ments should always be made at all thn<br />
supporting points of the outer tapered dis<br />
When adjusting the position of the idlir<br />
gear bearing, make sure that the prop<<br />
tension is restored on the toothed belt<br />
Shift the idling gear bearing only in tl<br />
direction of the motor inasmuch as tl<br />
screwing will permit.<br />
If your screen tower is down<br />
Call us up.<br />
Selby is standing by 24 hours a day.<br />
(Area Code 216 659-6631)<br />
We're in business to get you back in business fast . . . without<br />
costly delays. We've got the men, the materials, the equipment and<br />
more than 30 years of experience. Over 700 Selby screen<br />
towers are in<br />
service today. They're standing because we take pride<br />
in the product we build. So if your screen tower has gone<br />
with the wind, get in touch soon. We know exactly what to do to<br />
screen towers that are down and out.<br />
Note: High belt tension of all belts or<br />
any single belt makes the mechanism<br />
run hard. This may cause the centrifugal<br />
switch on the motor to delay for<br />
more than three seconds.<br />
In order to be able to remove the Sy<br />
chroflex wheel on the supply shaft fro<br />
projectors fitted with a magnetic sound un,<br />
remove the three screws and shift the re'<br />
Synchroflex wheel toward the gearing. It I<br />
then possible to reach the slotted-he:<br />
screw with which the big Synchroflex wht<br />
is mounted onto the supply shaft. Nc<br />
loosen the slotted-head screw and remo:<br />
the Synchroflex wheel. The wheel is reistalled<br />
in the reverse order, of course.<br />
Focus Adjustment<br />
puni<br />
Industries. Inc<br />
3920 Congress Parkway<br />
Richfield, Ohio 44286<br />
216-659-6631 (on 24-hour call)<br />
RED KEY Advertising Deadline:<br />
July 5, 1977<br />
linn<br />
When changing the film format, the:<br />
must not be any play in the focusing ;-<br />
rangement after the lens turret has intichanged<br />
the lenses. To adjust the focus ;-<br />
rangement, loosen the counter set screw I-<br />
low the lens mount. It is possible, then, )<br />
adjust the set screw so that the engagi;<br />
latch catches barely but safely. Then secU<br />
this adjustment with the aid of the oppos;<br />
counter screw. This procedure is the sat:<br />
for all positions of the lens turret.<br />
The lens guide rod and lens guide rail aj<br />
factory-adjusted to be parallel and are p-<br />
fectly aligned to the aperture by way of ts<br />
11I<br />
Continued on page 1<br />
18<br />
The<br />
MODERN THEATRE SECTlN<br />
j