4 cylinders + 6 cylinders 4 cylinders + 6 cylinders - Steyr Motors

More documents

Recommendations

Info

ToC 01 ENGINE SERVICE MANUAL MARINE ENGINES 01.02 CRANKSHAFT, BEARING, VIBRATION DAMPER 01.02.01 Replace crankshaft Preparation: Disassemble flywheel housing and flywheel, 01.03.01 und 01.03.02, Disassemble timing belt and vibration damper, Dissamble engine housing, 01.06.01, Disassemble oil suction pipe, 01.06.03. Disassemble oil pump housing, 01.06.02, 1 Turn crankshaft in such a way that first cylinder is located at TDC, and secure with locking pin No. 2300551/2. 02.01 ill.1 ATTENTION: While disassembling the connecting rod bearing caps and the main bearing caps, the crankshaft may not be turned. 2 Loosen the two screws of each connecting rod with special tool 2300746/0, remove connecting rod bearing caps with bearing shell. Push down all pistons and connecting rods to TDC position. 02.01 ill.2 NOTE: Remain with crank shaft in position during work operation to avaid damange the bearings. Never turn crank shaft. 3 Remove rocking pin. 4 Loosen two screws of each main bearing cap with special tool No. 2300747/0, remove main bearing shells and caps. 02.01 ill.3 5 Lift out crankshaft. Remove thrust bearings from main bearing section. ATTENTION: When removing, take care that released connecting rods do not hit against cylinder liner! 02.01 ill.4 Page ENGINE - 38 Z001019/0_6_July 2008
ToC SERVICE MANUAL MARINE ENGINES 01 ENGINE 6 Remove main bearing blocks. 7 Pull out oil nozzles for piston cooling. 02.01 ill.5 02.01 ill.6 8 Remove main bearing shells from bearing blocks. NOTE: For assembly, lubricate all bearing with engine oil. All pistons with connecting rods are inserted in the cylinder bore. Mount injection oil nozzles with new O- rings. When inserting the crankshaft, take care that the first connecting rod journal pin is positioned at TDC. 9 Check, fot proper installation main bearing shells and connecting rod bearing shells. 02.01 ill.7 ATTENTION:Main bearing base and main bearing cap are marked with consequential numbers on one side of the bearing cast. Make sure this number between base and bearing cap match. 02.01 ill.8 Z001019/0_6_July 2008 Page ENGINE - 39
Page 1 and 2:
STEYR MARINE ENGINES 4 CYLINDERS +
Page 3 and 4:
PREFACE STEYR MOTORS GmbH has devel
Page 5 and 6:
TABLE OF CONTENTS (MAIN ASSEMBLY GR
Page 7 and 8:
05 Cooling system 05.01 Cooler, hea
Page 9 and 10:
ToC SERVICE MANUAL MARINE ENGINES G
Page 11 and 12:
Page 13 and 14:
ToC SERVICE MANUAL MARINE ENGINES A
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
ToC SERVICE MANUAL MARINE ENGINES O
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50: ToC SERVICE MANUAL MARINE ENGINES G
Page 63 and 64: ToC SERVICE MANUAL MARINE ENGINES 0
Page 99: ToC SERVICE MANUAL MARINE ENGINES 0
Page 151 and 152:
ToC SERVICE MANUAL MARINE ENGINES 0
Page 153 and 154:
Page 155 and 156:
ToC SERVICE MANUAL MARINE ENGINES R
Page 157 and 158:
SERVICE MANUAL MARINE ENGINES 03 FU
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
SERVICE MANUAL MARINE ENGINES 03.14
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
SERVICE MANUAL MARINE ENGINES 05 CO
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
L J 6 5 4 2 3 1 23 ToC SERVICE MANU
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
ToC SERVICE MANUAL MARINE ENGINES I
Page 287 and 288:
ToC SERVICE MANUAL MARINE ENGINES E
Page 289 and 290:
Page 291 and 292:
ToC SERVICE MANUAL MARINE ENGINES I
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
°C °F 250 80 40 100 120 0 L MAIN
Page 301 and 302:
°C °F 250 80 40 100 120 0 MAIN RP
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331:
show all

4 cylinders + 6 cylinders 4 cylinders + 6 cylinders - Steyr Motors

Create successful ePaper yourself

Delete template?

Save as template?