en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro

93ACS800-04 sizeAA kWThree-phase supply voltage 525 V, 550 V, 575 V, 600 V, 660 V or 690 V-0011-7 13 14 11 11.5 7.5 8.5 5.5 R4 103 300-0016-7 17 19 15 15 11 11 7.5 R4 103 340-0020-7 22 28 18.5 20 15 15 11 R4 103 440-0025-7 25 38 22 23 18.5 19 15 R4 103 530-0030-7 33 44 30 30 22 22 18.5 R4 103 610-0040-7 36 54 30 34 30 27 22 R4 103 690-0050-7 51 68 45 46 37 34 30 R5 250 840-0060-7 57 84 55 52 45 42 37 R5 250 1010-0070-7 79 104 75 73 55 54 45 R6 405 1220-0100-7 93 124 90 86 75 62 55 R6 405 1650-0120-7 113 172 110 108 90 86 75 R6 405 1960-0145-7 134 190 132 125 110 95 90 R6 405 2660-0175-7 166 245 160 155 132 131 110 R6 405 3470-0205-7 190 245 160 180 160 147 132 R6 405 4180PDM code: 00096931-JSymbolsSizingNominalratingsI maxI cont.maxANo-overloaduseP cont.maxkWLight-overloaduseI 2N P NHeavy-duty useFramesizeAirflowHeatdissipationNominal ratingsI cont.max continuous rms output current. No overload capability at 40 °C.I max maximum output current. Available for 10 s at start, otherwise as long as allowed by drivetemperature.Typical ratings:No-overload useP cont.max typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,230 V, 400 V, 500 V or 690 V.Light-overload use (10% overload capability)I 2N continuous rms current. 10% overload is allowed for one minute every 5 minutes.P N typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,230 V, 400 V, 500 V or 690 V.Heavy-duty use (50% overload capability)I 2hd continuous rms current. 50% overload is allowed for one minute every 5 minutes.P hd typical motor power. The power ratings apply to most IEC 34 motors at the nominal voltage,230 V, 400 V, 500 V or 690 V.The current ratings are the same regardless of the supply voltage within one voltage range. To achievethe rated motor power given in the table, the rated current of the drive must be higher than or equal tothe rated motor current.Note 1: The maximum allowed motor shaft power is limited to 1.5 · P hd , 1.1 · P N or P cont.max (whichevervalue is greatest). If the limit is exceeded, motor torque and current are automatically restricted. Thefunction protects the input bridge of the drive against overload. If the condition exists for 5 minutes, thelimit is set to P cont.max .Note 2: The ratings apply in ambient temperature of 40°C (104°F). In lower temperatures the ratingsare higher (except I max ).Note 3: Use the DriveSize PC tool for a more accurate dimensioning if the ambient temperature isbelow 40°C (104°F) or the drive is loaded cyclically.I 2hdAP hdkW m 3 /h WTechnical data