en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro

More documents

Recommendations

Info

$\ATS\schemi\ATS con S3-S4-S5\Rm002101.dwg - VAE ProSys sro$

34360° high frequency grounding of the control cable shields is recommended at theirentries. The shields can be grounded by means of conductive shielding cushionspressed against the cable shield from both directions:Bare cable shieldShielding cushion(conductive)Cabinet bottom plateCable grommetCablePlanning the cabinet assembly
35Mechanical installationUnpacking the unitThe drive is delivered in a box that also contains:• plastic bag containing: screws (M3), clamps and cable lugs (2 mm 2 , M3) forgrounding the control cable screens• residual voltage warning stickers• hardware, firmware and other module manuals• delivery documents.Unpack the unit of frame sizes R2 to R5 as follows.TearMechanical installation
Page 3: ACS800-04 Drive Modules0.55 to 200
Page 7 and 8: 3Update Notice
Page 9 and 10: 5Connect the optional ASTO board as
Page 11 and 12: 7NEW (page 109): ASTO-11CNominal in
Page 13 and 14: 5Safety instructionsWhat this chapt
Page 15 and 16: 7GroundingThese instructions are in
Page 17 and 18: 9OperationThese warnings are intend
Page 19 and 20: 11Table of contentsACS800 Single Dr
Page 21 and 22: 13Motor cable shield . . . . . . .
Page 23 and 24: 15Altitude derating . . . . . . . .
Page 25 and 26: 17About this manualWhat this chapte
Page 27 and 28: 19Installation and commissioning fl
Page 29 and 30: 21Terms and abbreviationsTerm/Abbre
Page 31 and 32: 23ACS800-04/U4What this chapter con
Page 33 and 34: 25Main circuit and controlDiagramTh
Page 35 and 36: 27Planning the cabinet assemblyWhat
Page 37 and 38: 29Cooling and degrees of protection
Page 39 and 40: 31Inside the cabinetPrevent hot air
Page 41: 33Control panel mounting platform k
Page 45 and 46: 37Installation procedure1. Mark the
Page 47 and 48: 39R6 flange mounting12Lifting lugMo
Page 49 and 50: 41Planning the electrical installat
Page 51 and 52: 43Requirements tableThe following t
Page 53 and 54: 45Note 1: The abbreviations used in
Page 55 and 56: 47EEA / EuropeIf the drive is used
Page 57 and 58: 492) Circuit breakers which have be
Page 59 and 60: 51Selecting the power cablesGeneral
Page 61 and 62: 53Additional US requirementsType MC
Page 63 and 64: 55Before opening a contactor (DTC c
Page 65 and 66: 57Connection of a motor temperature
Page 67 and 68: 59Electrical installationWhat this
Page 69 and 70: 61Power cable connectionPower cable
Page 71 and 72: 63Frame sizes R2 to R4U1 V1 W1 UDC+
Page 73 and 74: 65Frame size R6: Cable terminal ins
Page 75 and 76: 67Connecting the control cablesConn
Page 77 and 78: 69360 degrees groundingInsulation12
Page 79 and 80: 71Installation of optional modules
Page 81 and 82: 7356 7RMIO boardRMIO board1 2 3 1 2
Page 83 and 84: 75Note: Location of the X41 termina
Page 85 and 86: 77Motor control and I/O board (RMIO
Page 87 and 88: 79External control connections (US)
Page 89 and 90: 81Relay outputsSwitching capacityMi
Page 91 and 92: 83Installation checklistChecklistCh
Page 93 and 94:
85MaintenanceWhat this chapter cont
Page 95 and 96:
87Fan replacement (R4)1. Loosen the
Page 97 and 98:
89Fan replacement (R6)To remove the
Page 99 and 100:
91Technical dataWhat this chapter c
Page 101 and 102:
93ACS800-04 sizeAA kWThree-phase su
Page 103 and 104:
95FusesgG and aR fuses for protecti
Page 105 and 106:
97Calculation exampleDrive:• ACS8
Page 107 and 108:
99ACS800-04 sizeUltrarapid (aR) fus
Page 109 and 110:
101The following parameters can eff
Page 111 and 112:
103NEMA dataRatingsThe NEMA ratings
Page 113 and 114:
105FusesUL class T fuses for branch
Page 115 and 116:
107Cable entriesBrake resistor, inp
Page 117 and 118:
109AGPS-11CNominal input voltage 11
Page 119 and 120:
111CE markingA CE mark is attached
Page 121 and 122:
113“C-tick” marking“C-tick”
Page 123 and 124:
115UL/CSA markingsULThe ACS800-04 a
Page 125 and 126:
117Dimensional drawingsWhat this ch
Page 127 and 128:
119Frame size R3 (with optional con
Page 129 and 130:
121Frame size R5 (with optional con
Page 131 and 132:
123Flange mounting kitsFlange mount
Page 133 and 134:
125Flange mounting kit for frame si
Page 135 and 136:
127Flange mounting kit for frame si
Page 137 and 138:
129AGPS boardDimensional drawings
Page 139 and 140:
131Resistor brakingWhat this chapte
Page 141 and 142:
133ACS800-04 typeACS800-U4 typeBrak
Page 143 and 144:
135Protection of frame sizes R2 to
Page 146:
3AFE68372984 Rev E ENEFFECTIVE: 31.
show all

en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro

Create successful ePaper yourself

Delete template?

Save as template?